Whirlpool Dishwasher Pump

The Pump and Motor Assembly is an OEM part for Whirlpool dishwashers. This assembly is responsible for circulating water through the dishwasher during the wash cycle, ensuring that dishes are thoroughly cleaned.

Over time, the pump and motor assembly can fail due to wear and tear, debris buildup, or electrical issues. Regular use, along with exposure to hard water, can cause the components to degrade, leading to performance problems.

Symptoms of a bad pump and motor assembly include:

• Dishes not being cleaned properly
• Unusual noises during the wash cycle
• Water not draining from the dishwasher
• Error codes indicating pump or motor issues

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Pump and Motor Assembly is an OEM part for Whirlpool dishwashers. This part is responsible for circulating water during the wash cycle and draining water at the end of the cycle.  

Causes of a bad assembly can include blockages from debris, electrical failures, or wear and tear from regular use.  

Symptoms of a bad Pump and Motor Assembly include:

• Dishes remaining dirty after a wash cycle
• Water not draining properly from the dishwasher
• Unusual noises during operation
• Error codes related to water flow or pump performance

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Volute with Seal is an OEM part for Whirlpool dishwashers. This part directs water flow within the dishwasher's pump, ensuring efficient circulation and pressure during the wash cycle. The seal helps to prevent leaks by maintaining a tight closure between the volute and other pump components.

Common causes of a bad volute with seal include wear and tear from regular use, damage from debris or hard water deposits, and seal degradation due to age or chemical exposure.

Symptoms of a bad Volute with Seal include:

• Water leaking from the pump area
• Decreased washing performance
• Unusual noises from the pump during operation
• Visible cracks or damage to the volute or seal

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This is a durable pump and motor assembly for dishwashers. The purpose of the pump and motor is to pump water that goes through the spray arms when the dishwasher moves through a cycle. If the pump and motor assembly isn't working correctly, it could lead to dishes that are dirty after a cycle is complete. Other signs of a bad pump and motor include pooling water after a cycle and whining noises.If the pump and motor assembly need to be replaced, make sure the dishwasher is unplugged. Use a pair of work gloves to protect the hands throughout the process. Close the water supply valve and disconnect the drain line. Replacing the pump and motor assembly may require tilting the dishwasher on its side to disassemble the components that are in the way of the replacement. Once the pump and motor have been removed, install the new parts and reassemble the dishwasher before use.Created for use with dishwashers by KitchenAid, Kenmore, and Whirlpool, this pump and motor assembly is a genuine OEM replacement part. It is sold as a single part. This component is directly sourced from the manufacturer.

This replacement part is a dishwasher pump and motor assembly. The dishwasher pump and pump motor circulate water through the dishwasher's spray arm. When the spray arms aren't spraying properly, this could mean that it's time for a new pump and motor assembly. Luckily replacing this part is a relatively simple process.Start by making sure the dishwasher is unplugged. After that shut off the water supply going to the dishwasher. Then disconnect the drain line from the garbage disposal or sink drain. Open the dishwasher door and pull out the bottom dish rack. Remove the upper dishrack from its track. Release the spray arm on the bottom of the washer. Then proceed to release the feed tube clips. Using a nut driver remove the bottom access panel and tow panel. Pull them out to remove them. Remove the power cable from the junction box, and disconnect the supply line from the inlet valve. Proceed to pull the dishwasher out of the counter. Tilt the dishwasher on its side and pull the hose from the drain pump. Remove the wire harness from the pump. Disconnect wires from diverter motor and circulation motor. Once complete, proceed to tilt the dishwasher upright and remove the pump and motor assembly from the bottom of the dishwasher. Replace with the new assembly.This replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.

The Pump-Drain is an OEM part for Whirlpool dishwasher modules. It serves as the water pump that actively removes dirty water from the wash chamber, directing it to the garbage disposal or home drainage system. 

Causes for a faulty Pump-Drain can stem from mineral buildup clogging impeller fins over time. Wear and tear on seals or electrical failure of motor components are also possible from prolonged usage.  

Symptoms of a bad Pump-Drain include:

• Incomplete draining or water remaining after cycles
• Strange gurgling or grinding noises during drain phase   
• Leaks detected around the drain hose connection
• Soap scum or film left inside from inadequate rinsing

This OEM replacement part works with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore dishwasher models as well. 

The Dishwasher Drain Pump is an OEM part for Whirlpool dishwashers. It is responsible for removing water from the dishwasher at the end of each cycle, ensuring that dishes are properly cleaned and dried.

Causes of a bad drain pump can include wear and tear from regular use, blockages from debris, or electrical malfunctions.  

Symptoms of a bad drain pump include:

• Water not draining from the dishwasher
• Unusual noises during the drain cycle
• Error codes related to drainage issues
• Water pooling at the bottom of the dishwasher

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Seal not included