Whirlpool Dishwasher Spray Arm & Related

This replacement upper spray arm restores strong spray coverage to the upper wash level of your dishwasher. It channels water through its jets and spins under pressure to help deliver consistently clean dishes on the top rack.

• Directs pressurized wash water to the upper wash level for thorough cleaning
• Rotates under water pressure for even spray coverage
• Helps clear food soils and detergent residue from dishes and glasses
• Common symptoms: poor cleaning on the upper rack, spray arm not spinning, clogged or cracked arm

• Disconnect power and shut off the water supply before servicing
• Open the dishwasher; remove the upper rack if needed for access
• Release or unthread the retainer and pull the old arm straight off; clear debris from the hub/feed port
• Seat the new arm and secure the retainer hand-tight; ensure the arm spins freely and run a test cycle

This mount secures the dishwasher's upper spray arm to its water feed, keeping the arm aligned and free to rotate so the upper rack receives consistent spray coverage and dependable cleaning.

• Supports and centers the upper spray arm at the correct connection point
• Helps maintain a solid connection to the feed tube/manifold for proper water delivery
• Wear, cracks, or looseness may lead to poor cleaning on the upper rack, arm wobble, or noise
• Replacing a damaged mount can help restore smooth spray arm rotation and wash performance

• Disconnect power and turn off water supply before servicing
• Pull out the upper rack; remove the upper spray arm from its mount
• Release the old mount's locking tabs or fasteners and remove it from the feed tube/tub
• Install the new mount fully, reattach the spray arm, and verify it spins freely before testing

This hub mounts on the pump outlet to secure and center the dishwasher's lower spray arm, allowing smooth rotation and even water distribution for consistent cleaning on the bottom rack.

• Anchors the lower spray arm to the pump/sump assembly
• Provides the pivot point so the arm spins freely
• Helps channel wash water into the spray arm
• Typical symptoms: arm not spinning, poor cleaning on the lower rack, wobbling/falling arm, scraping or grinding at the hub

• Disconnect power and water supply before servicing
• Remove the lower rack; lift off the spray arm and any retainer/screw if present
• Remove the old support from the pump outlet; seat the new support fully; reinstall the spray arm and fastener
• Verify the arm spins freely and clears obstructions; run a short test cycle to check operation

Upper spray arm with heatseal that restores water distribution to the dishwasher's upper rack for improved cleaning and rinsing. Replace a worn, cracked, clogged, or leaking upper spray arm to recover normal spray coverage. What it does:

• Directs pressurized spray to the upper rack so dishes and glassware rinse and wash more effectively; use when cleaning is inconsistent.
• Replaces cracked, bent, or clogged spray arm that no longer spins or sprays evenly.
• Includes a heatseal to help maintain a proper seal at the mounting area and prevent dripping or loss of water pressure.
• Helps eliminate symptoms like poor cleaning, visible water pooling, or uneven rinse patterns.

• Always disconnect power to the dishwasher (unplug or switch off the circuit breaker) before servicing.
• Empty and remove the upper rack to access the spray arm; inspect the mounting area and rotor for debris before installing.
• Installation is typically straightforward; confirm the attachment method for your model and use only OEM-recommended orientation.
• After installation, run a short cycle to check for leaks.

Also considered middle sprayarm on some dishwashers having a rinse arm on the ceiling.

Also Order Spray Arm Seal

This is the upper spray arm that distributes wash water to the top rack. Replacing a cracked, warped, or clogged arm restores even spray coverage and helps the arm spin freely so glasses and bowls come out consistently clean.

• Directs high-pressure jets to the upper rack and rotates under water pressure for full coverage
• Maintains even water distribution to improve cleaning performance
• Common symptoms of a failed arm: top-rack items not getting clean, arm not spinning, uneven spray, cracks or clogged nozzles

• Disconnect power and water supply before servicing the dishwasher
• Remove or lower the upper rack if needed; release the retaining nut/clip and pull the old arm straight off
• Seat the new arm fully on the hub/manifold and secure the retainer; verify it spins freely
• Run a short test cycle to ensure proper spray and operation

This tower protector is a small plastic cover that fits over the dishwasher's spray tower. It helps keep dishes and utensils from obstructing the tower's spray outlets so water can circulate properly for consistent cleaning.

• Shields the spray tower to prevent items from blocking water flow
• Helps maintain proper spray pressure and coverage to upper areas
• Replaces cracked, melted, or missing protectors that can lead to poor cleaning
• Common signs it's needed: protector is broken/loose, deformed, or repeatedly falls off; dishes aren't getting clean due to blocked spray

• Disconnect power and water before service
• Allow the dishwasher interior to cool
• Open the door, remove the lower rack, and snap the protector into place per the tower/rack design
• Verify it seats securely and does not interfere with the spray tower movement

This is the dishwasher upper spray arm that delivers water across the top rack for effective cleaning. It replaces a worn or damaged spray arm to restore proper water distribution and rinse performance. What it does:

• Spins and sprays water across the top rack to help remove food and detergent residue
• Restores proper spray pattern when the original arm is cracked, clogged, or not turning
• Helps prevent poor cleaning, spots, or missed areas on top-rack dishes
• Works with the dishwasher's water delivery system to maintain rinse and wash coverage

• One upper spray arm

• Turn off power and water to the dishwasher before beginning any service
• Inspect and clear any debris from the spray arm and the mounting area before installation
• Hand-tighten or snap the arm into place per your model's instructions; avoid overtightening

This manifold is the OEM gas valve assembly that routes propane or natural gas from the regulator to the oven and burner valves so the appliance can ignite and heat properly. Designed as a direct-replacement service part. What it does

• Channels gas from the regulator to individual burner/oven valves so each burner can ignite.
• Replaces a worn or damaged manifold that can cause weak or no ignition.
• Addresses symptoms such as burners that won't light, oven failing to heat, or inconsistent flame across burners.
• Works with the appliance's existing regulator and control valves when installed correctly.

• Turn off gas supply and electrical power before attempting removal or service.
• Inspect fittings and gaskets; replace any damaged seals to prevent leaks.
• After installation, perform a gas-leak test and verify proper ignition and flame patterns.

Includes both left and right arms.

The Upper Spray Arm is an OEM part for Whirlpool dishwashers. It is located below the upper rack and functions to spray water onto dishes during the wash cycle for thorough cleaning.

Causes of a bad upper spray arm include clogs or mineral buildup that reduce or block water pressure, or physical damage rendering the arm unable to spin properly.

Symptoms of a bad upper spray arm include:

• Dirty or inadequately cleaned upper rack dishes
• Spinning noises or clunking from the wash arm area
• Uneven cleaning results

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Center Wash Arm Assembly is an OEM part compatible with Whirlpool dishwashers. It is a multi-spraying component located in the center of the lower dish rack that helps deliver water for superior washing performance. The arm rotates during the cycle to wash all accessible surfaces of dishes.

Symptoms of a bad Center Wash Arm Assembly include:

• Incomplete or inadequate cleaning of dishes, especially those in the lower rack  
• Mineral or hard water deposits building up on dishes
• Reduced water pressure or spray pattern from the wash arm nozzle(s)

Causes of a bad center wash arm can be mineral deposits clogging the nozzle openings over time, or physical damage such as bending or breaking of the arm assembly or its mounting bracket.

This OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers.

This dishwasher spray arm directs rotating jets of water to clean dishes. Replacing a cracked, clogged, or broken spray arm restores proper water coverage for improved cleaning and more consistent wash results. What it does:

• Directs pressurized water through built-in nozzles to create rotating jets for effective dish cleaning.
• Helps maintain even water coverage across the racks; damaged or blocked arms can cause poor or uneven cleaning.
• Connects to the spray arm hub and turns during cycles; broken mounts or excessive wobble can cause noise or binding.
• Easy to inspect—look for visible cracks, clogged holes, or wobble that indicate replacement is needed.

• Disconnect power and turn off the water supply before servicing the appliance.
• Remove racks as needed to access the arm; clear debris from nozzles and the hub before installing the new arm.
• Install in the correct orientation and secure per OEM fitting—do not force or overtighten; ensure the arm spins freely.
• Run a short rinse cycle after installation to check for leaks.

Notes: Only one screw hole is used now.