Whirlpool Gasket & Seal

This door gasket seals the broiler/bottom-oven door to help retain heat for more even broiling and reduce stray heat into the kitchen. It replaces worn or damaged seals that allow heat loss or uneven cooking. What it does:

• Creates a heat-tight seal around the broiler/bottom-oven door to improve cooking performance
• Helps prevent heat loss, uneven broiling, or extended cook times caused by gaps in the door seal
• Wear signs include visible cracks, flattened or torn material, and gaps around the door edge
• Replacing a damaged gasket can reduce smoke from burning food debris caught in a torn seal

• Disconnect power (and gas, if applicable) and allow the appliance to cool fully before starting
• Remove the broiler drawer or door per the owner's manual to access the gasket channel
• Clean the gasket channel of debris before seating the new gasket; press the gasket into the retainer evenly

This is a replacement Seal - stopp that restores a secure seal to the original component, helping prevent leaks and keep the appliance operating normally. Use it when the original seal is worn or damaged. What it does

• Forms a tight seal at the mating surface to help stop water or air leaks
• Restores proper fit where a worn seal causes seepage or dripping
• Helps reduce related symptoms like water pooling beneath the appliance or visible leakage
• Simple, single-piece part designed to match the OEM sealing point

• Disconnect power to the appliance before starting work; turn off water supply if applicable
• Inspect mating surfaces and clean away debris or old sealant before installing the new seal
• Fit the seal fully into its groove or mounting location; do not stretch or twist the part during installation

A replacement door gasket that restores a tight seal to your appliance, helping maintain proper temperature control and preventing leaks or air exchange. Use this part when the existing seal is torn, deformed, or no longer sealing fully. What it does:

• Seals the door to prevent water, air, or cold/heat loss from the cabinet
• Helps maintain consistent internal temperature and efficient operation
• Reduces leaks, moisture buildup, and frost where applicable
• Common symptoms: visible cracks, gaps, warping, or leaking from the door area

• Disconnect power (and water if applicable) before starting any work
• Remove the old gasket completely and clean the sealing surface before installing the new gasket
• Align and seat the new gasket into the retainer; some models use screws or clips—refer to model-specific instructions
• Check the seal all the way around after installation and run a short cycle or close the door to ensure a proper fit

A general-purpose appliance adhesive used to bond and seal interior and exterior components. Restores secure attachment of trim, insulation, and small panels so parts stay in place and function properly. What it does

• Bonds loose trim, gaskets, and small plastic or metal panels to prevent shifting and rattles
• Seals minor seams and gaps to improve fit and finish
• Helps reattach insulation or padding that has come unglued
• Reduces noise from vibrating parts by securing components

• Clean and dry surfaces thoroughly before applying for the best bond
• Use in a well-ventilated area and avoid skin or eye contact; follow product safety directions
• Apply sparingly and allow full cure time per manufacturer instructions before reassembling

This rear icebox gasket seals the freezer/icebox compartment to help maintain proper temperature and reduce frost buildup. It restores the door seal so the appliance runs more efficiently and prevents moisture intrusion. What it does:

• Seals the icebox/freezer compartment to keep cold air in and warm, humid air out
• Helps prevent frost and ice buildup inside the icebox
• Reduces temperature fluctuations that can cause food spoilage
• Can stop condensation or water pooling caused by a failing door seal

• Unplug the appliance before attempting replacement
• Remove the old gasket fully and clean the mounting channel before installing the new seal
• Press the new gasket into the channel evenly; allow time for the gasket to form to the door

This genuine refrigerator door gasket creates an airtight seal around the fridge door to help maintain proper temperature and energy efficiency. Replacing a worn gasket restores seal integrity and helps prevent moisture and frost buildup. What it does:

• Seals the refrigerator door to keep cold air in and warm, humid air out
• Reduces frost and moisture accumulation inside the compartment
• Helps the compressor run less often by maintaining proper cabinet temperature
• Commonly replaced when you notice air leaks, visible gaps, or a damaged/warped seal

• One door gasket (1 each)

• Inspect the cabinet flange and mounting channel for damage before installing
• Clean contact surfaces and allow gasket to warm/settle for an even fit; follow OEM seating procedure
• Replace with the door closed and check for even contact around the entire perimeter

This door gasket seals the refrigerator/freezer door to keep cold air in and maintain consistent temperatures. A correct replacement restores the door seal to help prevent leaks, frost buildup, and inefficient cooling. What it does:

• Replaces a damaged or worn door seal to restore a tight closure between door and cabinet.
• Helps stop cold air from escaping, reducing frost buildup and uneven temperatures.
• Minimizes energy loss caused by gaps or cracks in the existing gasket.
• Addresses symptoms such as visible cracks, gaps when door is closed, or increased running time.

• One white door gasket (as pictured).

• Unplug the appliance or shut off power before starting any repair.
• Inspect and clean the gasket channel and mating surfaces before installing the new seal.
• Start by seating the gasket into the corners, then press the gasket evenly into the channel around the door.
• Avoid using sharp tools that could tear the gasket; refer to the appliance manual for any model-specific steps.

This switch seal is a replacement gasket that helps keep moisture and debris away from the appliance's door/control switch, protecting the switch assembly and helping restore reliable door detection and operation. What it does:

• Seals the area around the door/control switch to block water, lint, and grime.
• Helps prevent intermittent trips or failures caused by moisture or foreign material contacting the switch.
• Promotes consistent switch actuation and can extend the service life of the switch assembly.
• Useful when the existing seal is cracked, torn, flattened, or missing.

• Disconnect power before servicing to avoid electrical shock.
• Access typically requires removing the door trim or control panel—follow your model's service instructions.
• Inspect the switch and surrounding area for damage or corrosion and clean before installing the new seal.

This switch seal is a small rubber gasket that protects a control or door switch from moisture and debris, helping maintain reliable operation and prevent damage to the switch assembly. What it does:

• Creates a moisture- and dust-resistant barrier around a switch to reduce shorting and corrosion
• Helps keep switches operating smoothly by blocking contaminants that cause sticking or intermittent contacts
• Supports safe electrical performance by keeping water away from switch terminals and housings
• Common symptom linkage: switch malfunction, intermittent control, or moisture-related failures near switch area

• Disconnect power to the appliance before inspecting or replacing the seal
• Remove surrounding trim or components carefully to avoid damaging the switch or housing
• Confirm correct orientation and full seating of the seal during reassembly for an effective barrier
• If the switch shows damage or corrosion, replace the switch assembly as well

This switch bracket mounting seal replaces a worn or damaged seal that cushions and protects the door or control switch mounting area. It helps keep the switch assembly seated and reduces debris and moisture intrusion for reliable operation. What it does:

• Seals the switch bracket mounting area to protect the switch from lint, dust and moisture
• Helps keep the switch properly positioned for accurate door or control sensing
• Can prevent intermittent or failed switch contacts caused by contamination or misalignment
• Useful when replacing a brittle, torn or missing mounting seal during switch or door repairs

• Disconnect power to the appliance before starting any repair
• Remove the door or panel per service instructions to access the switch bracket area
• Fit the seal into the bracket groove or around the switch housing, ensuring full seating without stretching
• Inspect adjacent clips or screws and reuse or replace as needed; test the switch function after reassembly

This replacement knob grommet cushions and centers a control knob on the console, helping reduce wobble and protect the panel from wear for smoother, more secure knob operation. What it does

• Centers and cushions the control knob for proper alignment and tactile feel.
• Helps reduce knob wobble, rubbing, and wear on the control panel.
• Can address symptoms like loose, uneven-feeling, or noisy knobs when turning.
• Fits the knob mounting on compatible Whirlpool control panels for a restored fit.

• Disconnect power to the appliance before servicing.
• Remove the control knob, press the grommet into the panel opening, then reinstall the knob; generally requires no special tools.
• Inspect the knob and shaft—replace if damaged, as a damaged shaft can prevent a secure fit.
• Reconnect power and confirm proper knob alignment and operation after installation.

This pan gasket seals the refrigerator's drain/drip pan to help channel condensate and prevent water from leaking under the appliance. Replacing a worn gasket restores proper drainage and reduces puddling. What it does

• Seals the evaporator/drip pan to keep condensate contained and routed to the drain.
• Helps prevent water from collecting beneath or around the refrigerator.
• Commonly replaced when you see water on the floor, persistent puddles, or poor drainage.
• Works with the existing drain pan and support components to maintain correct drainage.

• One pan gasket

• Always unplug the appliance or disconnect power before starting work.
• Remove necessary access panels and the drip pan to access the gasket; handle panels and clips gently.
• Clean the pan and sealing surfaces before installing the new gasket to ensure a tight fit.
• If the pan is cracked or damaged, replace it too—gasket replacement alone won't stop leaks from a broken pan.