Whirlpool Gasket & Seal

Replacing the Door Gasket is very easy and will take about 2-3 mins per door. Simply remove the Gasket Retainer (1 screw), and pull off the old Gasket. Install the new gasket by simply pushing the gasket clips into the holes where the old clips came out from. Be sure to start gasket at the first hole either side of the Gasket Retainer and work your way around. Reinstall Gasket retainer. The Door Insulation is a very involved repair, and best to follow specific repair manual instructions. Door... Read more

Removed washer lid, then upper front panel with controls. Popped off the front retaining ring, then pushed the boot into the washer area after detaching the detergent hose and LED light from the boot. Detached the door lock mechanism. Removed the front panel with the door. Then removed main retaining ring after loosening with Phillips head screwdriver. Removed the old boot. I found a bunch of nasty stuff in the cavity between the main drum and rotating drum which was blocking the boot from... Read more

Replaced it with a new seal Read more

• Freezer section too warm

New gaskets. from appliance parts pros Read more

• Door sweating

Removed old door seal and replaced with the new one I purchased. Read more

Bought this door gasket and watched the video, very easy if you just take your time and start in one corner and go to the opposite corner. this way it stretches the seal completely into each corner. do as the video says and it will go great. Read more

I look on the internet i came a cross appliance parts pros i didnt no what i was looking for so i call the phone number talk to someone gave him the info he ask for they has what i was looking for in stock the guy was very nice he say i will get the part in two days and i got it in two days if i need a part for anything else i will ckeck out appliance parts pros when the door gasket came my grandson put it on in a flash Read more

I took the new seal out of it's packaging and used a blowdryer on low heat to soften up the seal so that the crease from shipping (it was folded to ship) disappeared. Next I took the refrigerator door off, removed the old seal, & cleaned the area where the new seal would be applied. Following the video on the Appliance Pro Parts website, I re-installed the new seal and put the door back on. Last step was to snap on the new hinge cap I ordered. The video online was easy to follow and this... Read more

Ordered replacement door seals, assistance picking the seals and speed of shipping was excellent. The installation was about as easy a job as can be, remove old seals, clean the doors and press in the new seals. With that said, I don't believe these are the same quality as factory original seals, the doors do not close as positive as the original and I have an air leak in the freezer door seal allowing condensation and ice to form. Read more

Removed front panel from refrigerator door and replaced the ice chute door seal and also replaced the seal inside the door that seals against the ice maker. Read more

Took the whole dryer apart to access the wheels (4) of them, belt and fan wheel, also had to clean all the lint out that somehow builds up inside the dryer. Plus cleaned out dryer duct vent, added to the time involved. If you are planning on fixing the dryer because of a noise which was in my case, I highly recommend buy all the parts for complete maintenance mentioned above. What helped save me time? I watch a dryer fan wheel replacement training video first, highly recommend this!... Read more

The new gasket arrived in a box half the size of the gasket so the gasket was folded to fit into the box. I hung the new gasket up for a couple of hours and then just prior to installation used a hair dryer as per included instructions to soften the gasket and minimize minor wrinkles in the gasket. The old gasket came out easily and the new went in easily. A 5 minute job in total. Read more

Replaced Case Water Filter assembly DA81-05883A. Please read my post entirely before starting. I completed all the tasks that I could without having to disconnect the refrigerator since it was full of food. First I removed the panel on top of the refrigerator that covers the water line that feeds the dispenser. Do not disconnect any electrical connections or the water line at this time. Remove the panel from the back bottom of the refrigerator that covers the compressor and water valve,... Read more

I ordered the gasket with the model number off the frig. AppliancePartPros.com made it easy to find my part. There was also a "how to" video on the same page. I ordered the part and it got to OH the next day. Following the video guideline it took me 15 minutes to remove the door, strip out the old seal and put in the new one. I will be ordering all my appliance parts from AppliamcePartsPros.com Read more

Ordered the correct gasket, watched video and completed the repair myself. Wasn’t hard at all. Read more

The gasket on my freezer door was not holding the door closes. When the main door closed, the pressure which shifts to the freezer was popping the door open and it was not closing because the magnet had lost its' mojo. I watched the video for the replacement of the gasket on the freezer door and my experience was exactly the same. One area that you should be mindful of: the depth of the fin on the replacement gasket is short, so do not make the slot of this fin too deep. When you are... Read more