Whirlpool Support Parts

Replacement support bracket that secures internal panels and assemblies inside your refrigerator. Restores proper alignment if the original is cracked or broken.

Molded wire clip that secures wiring and harnesses to the microwave cabinet. Replace if broken, cracked, or missing to prevent wire rubbing and chafing.

This Support (mounting bracket) secures internal components and stabilizes the appliance's assembly to help prevent sagging, misalignment and excess vibration. It's a small replacement that restores proper fit and reduces rattling. What it does:

• Provides a stable mounting point for panels or internal assemblies
• Keeps components aligned to prevent binding or wear
• Reduces noise caused by loose or sagging parts
• Helps stop intermittent contact or rubbing that can cause rattles

• Disconnect power (and water, if applicable) before servicing
• Access may require removing outer panels or trim; keep track of fasteners
• Support the assembly while replacing the bracket to avoid strain

This 22-inch strap snubber cushions and guides the dryer belt at the front of the drum to help reduce noise and prevent premature belt wear. It restores proper belt routing for smoother, quieter tumbling in compatible Whirlpool dryers. What it does:

• Cushions the belt where it contacts the front drum area to reduce rubbing and chafing.
• Helps maintain correct belt routing and tension to prevent slipping and uneven drum rotation.
• Can reduce squeaks, squeals, and jerky drum movement caused by a worn or broken snubber.
• Protects the belt from premature wear that may lead to fraying or failure.

• Disconnect power (and gas supply for gas dryers) before beginning any repair.
• Access typically requires removing the dryer front panel or drum—follow the OEM service manual for safe disassembly.
• Inspect the drive belt, idler pulley, and drum rollers when replacing the snubber; replace any worn parts.
• Wear gloves and eye protection.

Restores the outer housing on your refrigerator. Replaces a cracked, broken, or missing cover panel. Shields internal components from dust and debris.

Replace your refrigerator's support plate if it's cracked, broken, or missing. This mounting plate provides structural support for internal components.

The Strap is an OEM part for Whirlpool washing machines. It is a component located inside the washer tub that holds onto and spins the outer tub during the wash cycle. The strap washer plays an important role in securing the outer tub in place while continuously channeling rotational force to drive the washing action and clean clothes effectively. 

Causes of a bad strap can include wear and tear from years of use, damage due to impact or mishandling, or degradation from chemical exposure. 

Symptoms of a bad strap include:

• Excessive vibration or shaking during spin cycles
• Noise or grinding sounds coming from the washer tub area 
• The outer tub wobbling or moving more than usual
• Uneven agitation that fails to thoroughly clean all clothes

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Center wash arm assembly for dishwashers. Installs in the lower dish rack center position. Replace if cracked, broken, or not rotating properly.

Dishrack track rail for dishwashers. Mounts inside tub to guide rack smoothly in and out. Replace if cracked, broken, or causing rack misalignment.

Left-hand bracket that secures your dishwasher tub to the cabinet or countertop. Replace if cracked, broken, or missing to restore stability and alignment.

Replacement mounting plate for microwaves and over-the-range units. Restores proper fit and alignment. Replace when cracked, warped, or damaged.

Mounting clip that securely attaches your dishwasher under the kitchen counter. Replace if the original clip is broken, cracked, or missing.

Structural support bracket that mounts internal refrigerator shelves and bins. Replace if cracked, fractured, or broken from long-term use and vibration.

Replacement bracket that secures and supports internal dishwasher components. Install this support plate if your original is cracked, broken, or missing to restore alignment.

The dishwasher third level rack mount assembly is the bracket and hardware system that supports an upper utility rack for small items like lids, utensils, and small cups. It attaches to the dishwasher tub walls and holds the third rack at the correct height for proper water coverage. Replace this assembly if the third rack is sagging, won't stay in position, or the mounting points are cracked or broken.

Mounting bracket that secures internal microwave components. Replace if your original bracket is cracked, broken, or missing to restore proper alignment.