Whirlpool Support Parts

Secures the upper spray arm assembly in the dishwasher tub. Replace if cracked, broken, or worn causing the spray arm to droop or become misaligned.

Dishrack track rail for dishwashers. Mounts inside tub to guide rack smoothly in and out. Replace if cracked, broken, or causing rack misalignment.

Secures the middle wash arm manifold tube in your dishwasher. Replace if cracked, broken, or split from age or heat damage. Installs on manifold tube.

The Shock Absorber is an OEM part compatible with Whirlpool washing machines. It is a crucial component that helps reduce vibrations and dampens movement during the spin cycle. The shock absorber absorbs mechanical stresses to prevent the washer tub, suspension springs, and other components from wearing out prematurely.  

Causes of a bad shock absorber include wear and tear over time, cracks or breaks from heavy loads, or damage due to impact.  

Symptoms of a bad shock absorber include:

• Excessive shaking, vibration or noise during the wash and spin cycles   
• The washer walking or moving during operation
• Premature failure of other suspension parts like springs or the washer frame
• Potential leaks if movement stresses plumbing connections

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This dispenser water tube routes water from the inlet to the refrigerator's in-door dispenser manifold, helping ensure a steady, leak-free flow to the dispenser.

• Directs water from the supply line to the dispenser manifold
• A damaged or cracked tube can cause leaks, low/erratic dispenser flow, or air in the water line
• Replacing a leaking tube can help restore normal dispenser operation and prevent water damage

• Unplug refrigerator and shut off water supply before service
• Have a towel/container ready to catch residual water
• Note tube routing and connections; push-to-connect fittings may require firm seating for a watertight seal
• After installation, turn water on and check all joints for leaks

Secures the upper spray arm to the water feed. Replace if cracked, broken, or loose to restore proper arm alignment and rotation for the top rack.

Replaces broken or worn washer shock absorber that controls tub movement during spin. Installs on washer suspension to reduce vibration and shaking.

Secures the dishwasher's water inlet tube in position, preventing movement and strain on fittings. Replace if cracked, broken, or missing to restore support.

There is a split at the 3 O'clock position. Color: white. It measures about 3 inches wide by 4 inches high.

Fixes food freezing in fridge and popping/tapping noises from damper. Restores proper airflow between freezer and fresh food sections. 5-15 minute repair.

This bracket mounts inside the dishwasher tub and supports the middle spray arm manifold tube, holding it securely in position. It ensures the spray arm tube stays aligned so water is properly distributed during the wash cycle. Replace this bracket if the middle spray arm wobbles, falls out of place, or if dishes on the upper rack are not getting clean due to poor water coverage.

Mounts on the pump outlet to secure and center the lower spray arm. Replace if cracked, broken, or worn to restore proper arm rotation and alignment.

This upper dishrack track mounts to the dishwasher tub wall and provides a smooth glide path for the rack rollers. Replacing a damaged track restores easy in-and-out movement and helps keep the upper rack aligned and secure.

• Guides and supports the upper dishrack as it slides in and out
• Maintains rack alignment to prevent binding or derailing
• Typical failure signs: rack jams or falls off, rough/squeaky travel, visible cracks or breaks in the track
• Can keep the rack from fully sliding in, making the door harder to close

• Disconnect power and turn off the water supply before servicing
• Remove the upper rack by releasing the end caps/stops
• Unfasten the old track from the tub (screws/clips), then position and secure the new track
• Reinstall the rack and end caps; verify smooth rack travel before restoring power and water

The lower wash arm support cap secures and stabilizes the lower spray arm while allowing it to rotate freely during wash cycles. Positioned at the center of the dishwasher floor beneath the lower dish rack, it requires replacement when the wash arm wobbles, doesn't rotate, or when dishes in the lower rack remain dirty.

Secures the fold-down tine row on your dishwasher rack. Replace this retainer if it's worn, broken, or missing to restore smooth pivoting and stability.

Includes suspension pads.