Whirlpool Switch

This infinite switch controls the variable heat settings for a cooktop surface burner, restoring adjustable heating for smooth cooking. It replaces a failed control to help the burner reach and hold selected temperature levels. What it does

• Regulates power to a surface element so heat changes smoothly from low to high.
• Common symptom: burner won't heat or only works on one setting.
• Common symptom: heat level won't change or is stuck at a single setting.
• Can cause clicking or intermittent burner operation when failing.

• Disconnect power to the appliance at the breaker before servicing.
• Confirm terminal locations and wiring match your original switch; label wires before disconnecting.
• Access typically requires removing the cooktop or control panel.

This burner ignitor switch controls spark delivery to a cooktop burner so the burner lights when the knob is turned. It replaces a worn or failed switch to restore ignition responsiveness and consistent sparking. What it does:

• Routes spark current to the surface burner ignitor when the control knob is turned
• Stops spark delivery when the control knob is released or turned off
• Commonly used when a burner fails to spark or sparks intermittently
• Works with the cooktop's ignition system to enable safe, reliable lighting

• One burner ignitor switch

• Disconnect power (and gas if applicable) before servicing to avoid shock or injury
• Access may require removing the cooktop or control panel
• Verify wiring and switch operation with a multimeter before replacement

Color: Black

This temperature switch is a thermostat-style switch that senses and controls temperature to help the appliance maintain safe operating temps and proper heating performance. Replace a failed switch to restore normal temperature regulation. What it does:

• Senses temperature and opens or closes the circuit based on set thresholds
• Signals the control system to stop or allow heating to prevent overheating
• Commonly associated with no-heat, intermittent heating, or overheating symptoms
• Acts as a safety/limit device in heating circuits

• One temperature switch

• Disconnect power to the appliance before starting any repair
• Handle terminals carefully; ensure secure electrical connections without bending terminals

This pushbutton switch restores a single button on the appliance control panel so you can reliably send selection or command inputs to the control board. It replaces a worn, stuck or non-responsive panel button. What it does

• Acts as the user-facing pushbutton that completes the control input circuit when pressed
• Sends selection/command signals to the appliance control board or timer
• Common symptom fixer: button that won't register presses or responds intermittently
• Also used when a button is physically stuck, loose, or missing

• Disconnect power to the appliance before beginning service to avoid shock
• Access typically requires removing the control panel or overlay—retain screws and trim
• Verify connector orientation and seating; do not force connectors or terminals

This water level switch detects the washer's water height and signals the control to start and stop filling, helping maintain proper wash cycles and prevent overfilling. What it does:

• Senses water level via a pressure hose and tells the control when to stop filling.
• Can cause continuous filling, overfilling, or failure to advance cycles when faulty.
• Works with the washer's control board and pressure hose to regulate fill actions.
• Intermittent or no fill/no water level detection are common symptoms of failure.

• Disconnect power and water supply before beginning any repair.
• Carefully detach the pressure hose from the switch; replace with correct routing to avoid kinks.
• Inspect and replace a cracked or clogged pressure hose when present; verify hose connection is airtight.
• Test switch continuity with a multimeter per service instructions; refer to the service manual for wiring and diagnostic steps.

This genuine replacement wire harness connects and routes power and signal lines between appliance components, restoring reliable electrical communication for normal operation and control response. What it does:

• Replaces damaged or frayed wiring that can interrupt power or signals
• Restores reliable connections between controls, motors, and sensors
• Helps resolve intermittent operation, loss of certain functions, or failure to start when caused by wiring faults
• Provides factory-style connectors and routing for secure, vibration-resistant connections

• Disconnect power to the appliance before starting any repairs
• Handle connectors carefully; match connector shapes and colors to the original
• Route the harness as the OEM diagram specifies and secure with clips or ties to prevent chafing

Replacement burner switch that controls the heat level for an electric range surface element, restoring proper temperature selection and burner responsiveness. Use this switch when a burner is unresponsive, stuck at one setting, or heats erratically. What it does:

• Regulates power to a surface element so you can select low-to-high heat settings.
• Replaces a failed surface control switch that prevents burners from changing temperature.
• Common symptoms it can fix: burner won't heat, stuck on one setting, no click/response, or inconsistent heat.
• Works as the control interface between the knob and the element on compatible electric ranges.

• Disconnect power at the breaker or unplug the range before starting any repair.
• Photograph or label wires before removal and match terminals exactly when installing the replacement.
• Use insulated tools and avoid contact with live terminals; restore power only after reassembly.

Color: White

This control switch is the user-facing rotary selector that lets the appliance select cycles and settings. It restores clear, tactile control so the unit responds correctly when you turn the knob. What it does:

• Selects operating cycles and settings when the knob is turned
• Routes electrical signals from the control panel to the selected function
• Commonly replaced when settings do not change or the control feels loose/slips
• Resolves intermittent or unresponsive cycle selection and erratic behavior

• Disconnect power before attempting any repair to avoid electrical shock
• Accessible from the control panel; remove trim or console as needed per your model's service instructions
• Test function after reassembly; do not force the selector or use excessive torque

This safety switch actuator engages the door/interlock switch so the appliance senses a closed, secure door and will run as intended. Replacing a worn actuator restores reliable door engagement and control-system signaling. What it does:

• Moves the door latch into position to trip the appliance's safety/interlock switch
• Ensures the control board senses a closed door so cycles can start or continue
• Common symptom: appliance won't start or stops when the door is shut or nudged
• Common symptom: door won't fully latch or feels loose when closing

• One safety switch actuator

• Disconnect power (and water if applicable) before starting any repair
• Remove exterior panels or door assembly as needed to access the actuator; keep fasteners organized
• Verify switch alignment with the actuator and test operation before reassembly
• Wear gloves and eye protection