Whirlpool Washer Parts

Fix a leaking or broken dispenser drawer that won't release detergent or fabric softener properly. Direct replacement restores proper dispensing.

This lower wire harness routes power and signals between the control and the components beneath the tub on select 4.7/4.8-cu ft top-load washers. Replacing a damaged harness restores reliable connections and helps resolve intermittent motor or pump operation. What it does:

• Distributes power and control signals to lower-cabinet components
• Supports proper operation of the drive motor, drain pump, and related parts
• Typical symptoms: no spin or agitate, won't drain, intermittent operation, or visible heat damage/corroded connectors
• Match by part number for correct fit on 4.7/4.8-cu ft platform models

• 1 lower wire harness assembly

• Disconnect power and water supply before servicing
• Access the underside per your model (tilt the washer or remove panels as required)
• Transfer one connector at a time; route along the factory path and secure with existing clips/ties away from moving parts and sharp edges
• After installation, run a diagnostic or test cycle to normal operation

This is an electric drain pump that removes water from the wash tub during the drain and spin cycles of a washing machine. It is typically mounted at the bottom of the washer and connects to the drain hose. Replace this pump if the washer fails to drain, drains very slowly, or makes loud humming or grinding noises during the drain cycle.

Fix detergent not dispensing or leaking into the tub. This washer dispenser drawer replaces worn seals and clogged ports for reliable dosing.

Replacement power cord that connects your washer to the wall outlet. Includes strain relief for cable protection. Needed when original cord is damaged, pinched, shorted, or worn. Direct plug-in installation.

Cap seal creates a tight barrier between cap and mating surface to prevent leaks. Replace when worn or damaged to restore secure fit. Confirm compatibility.

Mounts inside the washer drum to lift and tumble laundry evenly. Replace if cracked, broken, loose, or missing to restore proper tumbling action.

Fix detergent not dispensing or drawer leaking issues with this washer dispenser drawer assembly. Holds detergent and fabric softener during wash cycles.

Right-hand door hinge for dryers. Replaces broken, bent, or sprung hinges that prevent the door from closing properly. Easy DIY installation.

Secures the motor to its mounting point in your laundry center. Replace if the retainer is worn, broken, or has lost tension to prevent motor misalignment.

Washer making loud grinding noise during spin? A damaged motor rotor with worn splines or cracked magnets causes this. Repair guide included.

The Shock Absorber is an OEM part compatible with Whirlpool washing machines. It is a crucial component that helps reduce vibrations and dampens movement during the spin cycle. The shock absorber absorbs mechanical stresses to prevent the washer tub, suspension springs, and other components from wearing out prematurely.  

Causes of a bad shock absorber include wear and tear over time, cracks or breaks from heavy loads, or damage due to impact.  

Symptoms of a bad shock absorber include:

• Excessive shaking, vibration or noise during the wash and spin cycles   
• The washer walking or moving during operation
• Premature failure of other suspension parts like springs or the washer frame
• Potential leaks if movement stresses plumbing connections

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

The Dryer Door Handle is an OEM replacement part for Whirlpool dryers. A dryer door handle can deteriorate due to prolonged use, repeated force when opening or closing the door, or accidental impact that causes cracks or breakage. These factors may compromise the handle's structural integrity and make it less reliable.

Color: White

Symptoms of a bad Dryer Door Handle include:

• Loose or wobbly handle
• Cracks or visible damage to the handle
• Difficulty opening or closing the dryer door

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This water level pressure switch senses tub water level and signals the control to stop filling and advance the cycle. Replacing a failed switch restores proper fill shut-off and allows the washer to move to wash, drain, and spin.

• Detects water level via air pressure in the attached hose from the tub air dome
• Signals the timer/control to close inlet valves at the selected fill level
• Enables agitation and spin only when the level is appropriate or the tub is empty
• Typical symptoms of a failed switch include overfilling or underfilling, continuous filling, cycle not advancing, or no spin

• Disconnect power and turn off water supply before servicing
• Access the switch in the control console or top panel; note wire locations for reassembly
• Transfer the pressure hose and wire connectors to the new switch one at a time; ensure the hose is clear, not kinked or cracked, and fits snugly
• After installation, run a quick fill test to ensure proper shut-off and cycle progression

Fix washer water leaking into tub or slow dripping when off. Water inlet valve assembly replacement stops fill valve leaks. Easy DIY repair with video.

Replace your washer's cracked or leaking outer tub. This housing holds the inner basket and prevents water from leaking into the machine's interior.