Need Help?
Call
Restores a solid grip on your laundry center door. Replace this handle when the original is cracked, broken, or loose for smooth opening and closing.
Installed new one. About 10 minute job. Read more
Washer stops mid-spin or shows F6E1 error? The motor control board regulates drive motor speed and direction. Most DIYers replace it in 15-30 minutes.
On-line chat with AppliancePartsPros told me the error code was was for motor speed and they sent me a .pdf file on what to do to T/S it. Following the sheet I checked motor and Tack resistance and wiring - all OK, so I ordered a Motor Controller Ckt board assy. It arrived in 24 hours, during that time i watched the replacement videos and removed the old part. Upon receiving the new part I installed it (15 min), tested the washer (it worked), then put all the panels back on, pushed the washer... Read more
Left-side door hinge for dryers. Replaces broken, bent, or deformed hinges that prevent the door from closing properly. Simple installation.
I removed the old hinges and replaced them with the new hinges. It was probably the easiest repair I've ever had to do. Read more
This is a water inlet valve that controls the flow of water into the washing machine during fill cycles. It is an electrically operated valve that opens and closes to allow hot or cold water into the tub as directed by the control board. Replace this valve if your washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it should stop.
Ordered this part and just changed it out. Not hard once I figured out how to get in to it. Read more
This retainer ring is a genuine OEM replacement part sourced directly from the manufacturer for use on front load washing machines to hold the boot seal in place. The boot seal is the gasket that seals the washing machine when the door is closed to prevent water from leaking. The retainer ring is located flush against the boot seal and has either a spring clamp or screw clamp that secures it. Over time, this ring may become damaged due to the washing machine's normal use and age. If the ring is not tight, the washing machine could leak when in use. If water is coming from the door, it is a good idea to inspect and replace the retainer ring and possibly the boot as well.Unplug the washing machine to prevent electrocution. Remove the front panel, the detergent dispenser, and the kickplate to access the retainer ring. Locate the clamp on the ring and loosen it. Remove the retainer ring and set it to the side. Inspect the boot and then install the new retainer ring. Tighten the clamp and reassemble the washing machine. This retainer ring is sold as an individual unit. It is designed specifically for washing machines manufactured by Whirlpool.
Im not a repairman, so all my knowledge to fix my washer came from either youtube or online chats. I posted this to help the next dad trying to save a few bucks. Door sensor... Since door sensor worked correctly, verified that by starting washer with door open, and agitate cycle would not start until door was closed. Meaning door sensor worked correctly. Timer... In high spin cycle washer sounded correcltly spinning, but when opening door, drum was was not moving. So timer was triggering... Read more
Missing or cracked cap letting water into the agitator? This protective cover seals openings and fasteners, preventing leaks and debris buildup. Easy DIY fix.
Washer won't start or door won't unlock? This lock cam drives the door lock mechanism to secure and release the door for proper cycle operation.
Using a punch and a big hammer I forced the lock through the housing, replaced the old lock with the new one and was done!!!! Really easy!!! Read more
Replacement door hinge for laundry center appliances. Restores smooth opening and closing when original hinge is cracked, broken, or worn out.
The parts arrived in a timely fashion. I was able to replace the valve and pressure switch in a relatively short time - about an hour. A tenant called me to thank me and said that the machine is working well. The hinge arrived broken. I informed AppliancePartsPros and I received a replacement hinge the next day. I was very impressed! Putting the new one on was not difficult; about a half-hour in total. BTW, I am self-taught, with the help of online videos, in the repairs of our machines (a... Read more
Secure brackets and hardware for stacking a dryer on top of a front-load washer. Needed when vertically installing units to save floor space.
No one locally had any stack kits, nor could they tell me if it was even possible to stack appliances of differing models. Your technician took the time to help solve the problem. The stack kit fits perfectly. Read more
Attaches to the timer shaft to select wash cycles and start your washer. Replace this knob if it's cracked, stripped, broken, or missing to restore control.
I diagnosed the problem, identified faulty parts, and replaced those components. Read more
This is an electrically controlled water inlet valve that opens and closes to allow hot and cold water into the washing machine during the fill cycle. It is activated by the washer's control board or timer to regulate water flow at the correct times. Replace this valve if the washer is not filling with water, fills slowly, continues to fill when turned off, or leaks from the back of the machine near the hose connections.
I called AppliancePartsPros to find a replacement water inlet valve. They talked me through finding the clothes washer model number. Once the model number was located, the AppliancePartsPros person on the phone found the correct replacement valve. I received the valve 3-5 days after ordering. I downloaded the clothes washer repair manual and watched some YouTube videos regarding valve replacement. I followed the steps in the repair manual being careful to mark anything I had removed during... Read more
Fix a washer that won't fill with water or overfills with this water level pressure switch. Controls proper water amounts for each wash cycle.
Replaced the faulty switch with the new part. Found out tge problem by doing a simple Google search! Read more
Color: White. This washer lint filter is also known as the upper agitator.
Bought a new upper agitator/filter housing. Just slide it over the bottom agitator housing and put the cap from the old one on the new one. Takes maybe 3 minutes to do. The screen inside the lower part of the housing/filter holds it snug to the bottom housing and does not fly off during the spin cycle. Works great. Read more
Fix a washer that won't advance cycles or spin with a new timer. Controls wash, rinse, and spin phases. Common DIY repair with clear instructions.
I looked on your site and found troubleshooting diagnostic and then ordered timer. The timer was not hard to remove and install new one. Read more
This is an electrically operated water inlet valve assembly with a built-in vacuum break (backflow preventer) for a washing machine. It controls the flow of hot and cold water into the wash tub when the machine fills during a cycle. Replace this valve if the washer is not filling with water, fills slowly, continues to fill when it should stop, or if you notice water leaking from the valve area.
New valve. Read more
Dryer door won't stay closed? This door strike engages with the catch to secure the door. Simple DIY fix in minutes with basic tools and video guide.
Removed and replaced with new strike and catch. Per instruction video. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.