Whirlpool Washer Parts

Fix a leaking or broken dispenser drawer that won't release detergent or fabric softener properly. Direct replacement restores proper dispensing.

Fix slow filling or loud screaming noises during wash cycles. This water inlet valve controls flow into your washer tub. Moderate DIY repair.

Directs defrost water from the evaporator to the drain pan. Replaces cracked, broken, or deformed drain tubes causing leaks or ice buildup issues.

The Coin Slide Interface is an OEM part for Whirlpool commercial washers. It is a component that allows users to insert coins or tokens to activate the machine and initiate the laundry cycle.

Causes of a faulty coin slide interface can include regular wear and tear, damage due to misuse or vandalism, or electrical component failure. These factors can result in issues such as coin rejection, incorrect coin counting, or the inability to start the machine using coins.

Symptoms of a Bad Part:

• Will not start
• Not washing properly
• Timer will not set

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This is a chrome-finished timer knob that attaches to the timer shaft on the dryer's control panel, allowing you to select and start drying cycles. It is made of plastic with a metallic chrome appearance. Replace this knob if it is cracked, broken, or no longer grips the timer shaft properly, making it difficult to turn or set the dryer cycle.

This is a decorative trim bezel that surrounds the lid lock mechanism on a top-load washing machine, finished in chrome shadow. It snaps into place around the lid lock area to provide a clean, finished appearance. Replace this bezel if it is cracked, discolored, or broken, which can also affect proper lid lock alignment.

Replacement timer knob for washers. Installs on the control panel to operate the timer dial. Order if your original knob is cracked, broken, or missing.

This water level pressure switch senses tub water level and signals the control to stop filling and advance the cycle. Replacing a failed switch restores proper fill shut-off and allows the washer to move to wash, drain, and spin.

• Detects water level via air pressure in the attached hose from the tub air dome
• Signals the timer/control to close inlet valves at the selected fill level
• Enables agitation and spin only when the level is appropriate or the tub is empty
• Typical symptoms of a failed switch include overfilling or underfilling, continuous filling, cycle not advancing, or no spin

• Disconnect power and turn off water supply before servicing
• Access the switch in the control console or top panel; note wire locations for reassembly
• Transfer the pressure hose and wire connectors to the new switch one at a time; ensure the hose is clear, not kinked or cracked, and fits snugly
• After installation, run a quick fill test to ensure proper shut-off and cycle progression

This water inlet valve controls the flow of hot and cold water into the washing machine tub during fill cycles. It contains solenoid-operated ports that open and close in response to signals from the control board. Replace this valve if your washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it shouldn't.

Replacement power cord that connects your washer to the wall outlet. Includes strain relief for cable protection. Needed when original cord is damaged, pinched, shorted, or worn. Direct plug-in installation.

The Shock Absorber is an OEM part compatible with Whirlpool washing machines. It is a crucial component that helps reduce vibrations and dampens movement during the spin cycle. The shock absorber absorbs mechanical stresses to prevent the washer tub, suspension springs, and other components from wearing out prematurely.  

Causes of a bad shock absorber include wear and tear over time, cracks or breaks from heavy loads, or damage due to impact.  

Symptoms of a bad shock absorber include:

• Excessive shaking, vibration or noise during the wash and spin cycles   
• The washer walking or moving during operation
• Premature failure of other suspension parts like springs or the washer frame
• Potential leaks if movement stresses plumbing connections

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

Fix a washer that won't agitate or clean clothes properly. This washplate restores wash action when splines are worn or stripped. Easy 5-10 minute DIY repair.

This is a rubber drive belt that connects the motor to the wash basket in a top-load or front-load washing machine. It transfers rotational force from the motor to spin and agitate the drum during wash and spin cycles. Replace this belt if the washer drum does not spin or agitate, makes a burning rubber smell, or if the belt appears cracked, frayed, or stretched.

The Dryer Door Handle is an OEM replacement part for Whirlpool dryers. A dryer door handle can deteriorate due to prolonged use, repeated force when opening or closing the door, or accidental impact that causes cracks or breakage. These factors may compromise the handle's structural integrity and make it less reliable.

Color: White

Symptoms of a bad Dryer Door Handle include:

• Loose or wobbly handle
• Cracks or visible damage to the handle
• Difficulty opening or closing the dryer door

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Fix detergent not dispensing or leaking into the tub. This washer dispenser drawer replaces worn seals and clogged ports for reliable dosing.

Fix water leaking from your detergent drawer. This dispenser holds and releases detergent, softener, and bleach at the right time. Easy DIY repair.