Need Help?
Call or text
Illuminates the dryer drum for better visibility when loading and unloading. Replace when bulb burns out or fails to light. Confirm fit with your model.
Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more
Rubber washer that seals beneath the agitator bolt to secure the agitator to the drive shaft. Replace if agitator loosens or leaks occur. Verify fit.
I replaced the washer plate and new screw/washer part. Easy fix and back up and running in ubder 10 minutes. Read more
Washer won't spin or stops mid-cycle? A faulty lid lock strike prevents the lid from securing properly. Moderate DIY repair with included video guide.
The part is so new no video so I went onto a similar part and watched video that got me about 80%. Then, called and customer service sent me a service Manual but this still was not specific so I broke the old to get it out and in the process figured out how to do it correctly. So I installed the last bit of it which was the bezel through the machine top by myself correctly. So you take the old one out by pushing out to the right from the bottom side using a screw driver for leverage. It will... Read more
Replace your cracked, broken, or warped washer lid assembly. Covers the wash tub and hinges open for loading. Hinges sold separately. DIY installation.
Replaced lid. Read more
Fix F03 E01 or F08 E01 error codes with a new water level pressure switch. Controls fill and drain cycles. Easy 5-minute DIY replacement for washers.
I contacted AppliancePartsPros and gave them my symptoms and failure codes and they were able to diagnose the problem and send the correct parts to resolve the issue. This is the 3rd or 4th time I've used their service since 2012 and they have been correct on each and every repair issue I've had. Many thanks for the professional advice and help! Read more
Washer won't start or stops mid-cycle when door opens? The door switch detects door position for safe operation. DIY repair in 10-20 minutes with video.
The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more
Replace your washer door bellow seal if you notice water leaking from the front door or visible tears in the rubber. Confirms fit by model number.
I followed the very well made repair video for this particular part. The total time it took for the repair was under 20 minutes. But I have a suggestion for the repair video and that is to emphasize that when reinstalling boot. Have the tachnician point out that there are drain holes in the boot that need to be situated and reattached toward the bottom of the washer chassis. Unfortunately I had to redue and double the repair time because the wash water would not drain properly during wash... Read more
Set of 4 suspension rods and springs that support the washer drum. Replace when rods are worn, cracked, or bushings are broken to restore balance.
Replace suspension rods. Read more
Loud grinding noise during spin cycle? Failed gearcase bearings cause noise and oil leaks. Moderately difficult repair requires disassembly and cleanup.
Disassembled washer and replaced gearcase and reassembled. Read more
Washer won't spin or agitate? A faulty direct drive motor often causes spinning failure and burning smells. Moderate DIY repair in under 2 hours.
All's well that ends well, but the getting there was a bit of a pain. The web site suggests 3 possible causes for my problem (incl. the burning smell). I began with the first two since they were inexpensive compared to the motor, which was the third cause (and also the least often cause). There is no way to visibly tell if the motor is bad or not. After replacing the clutch assembly, which did have some plastic pins broken off) and the motor coupling (which actually looked fine, but the... Read more
This washer drain pump moves water out of the washer during drain and spin. Replacing a worn or failed pump restores proper draining so cycles finish on time and the basket can reach full spin speed.
What it does
What’s included One drain pump assembly.
Install notes
This OEM drain pump is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Ordered the correct part/ Pump from this Awesome website and replaced the drain pump. Good to go!! Read more
Secures the washplate to the drive shaft in your washer. Replace if stripped, damaged, or missing during washplate repairs or agitator service.
Fix a washer that won't agitate or clean clothes properly. This agitator replacement restores wash action. Moderate DIY repair, requires removing bolt.
I had to cut the old agitator out with an oscillating saw in order to access the agitator drive. This is the second Maytag (MVWC 565) I have had to do this to. I first tried removing it by sliding straps under the agitator then then using a jack to pull it loose which did not work either time. One suggestion I have would be to remove debris from tub as you cut in order to prevent it from dropping from the inner tub into the outer tub. Read more
Flexible seal between washer door and drum that prevents leaks during operation. Replace if torn, cracked, bulging, moldy, or leaking. Confirm fit with your model number.
Replaced the bellow. Read more
Washer won't agitate or makes clunking noise? This thrust washer reduces friction in the transmission system. Easy DIY repair with video guide.
Pulled the washer apart (using your videos as a refresher) and found that the plastic coupling between the motor and the transmission had failed. Searched for parts vendors and found your site. Ordered the coupling on-line and went back down to clean up the machine. In the cleaning process I found a damaged thrust washer for the upper agitator and broken drive dogs for that same agitator. I went to the website to see if I could augment my initial order. I did not want to pay shipping costs... Read more
Replacement door handle for front load washers. Installs on the outer door panel. Replace if cracked, broken, or loose from wear or excessive pulling.
I purchased the parts from appliance parts pros and followed their repair video, to complete the repair myself. It took about 10 minutes, with complaining kids in the background. It was simple, and saved me a ton of money. Read more