Whirlpool Washer Parts

Replaced internal drain hose. and while I was in there I changed some known wear items. water pump,direct drive coupling tub to pump hose and a spring Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

• Lid or door won't close
• Lid or door will not open

I removed the two screws and all the pieces that were broken. Went online to Appliance parts.com, searched for the part using the model number from the machine and ordered the part . part arrived in 2 days and with a Phillips screwdriver was installed in less than 5 minutes. Read more

Took off cover, installed new parts. Read more

• Spins slowly
• Will not agitate
• Pumps but will not spin

My parents have the older 80 series washer and dryer that gets used way more than a consumer washer and dryer was ever meant to be used. The washing machine finally said im tired. During the spin cycle it was making a really loud squealing noise and during the agitation cycle it would barely agitate the clothes. So i ordered the basket drive to get rid of the squealing during spin cycle and noticed the dogs on the cams were warn and werent grabbing so ordered the whole cam kit to be safe... Read more

In reality, this turned into a full-on rebuild project - with several parts orders, not just a simple repair. But I have to give credit: The parts listings with pictures on the AppliancePartsPros web site were really useful in figuring out what was going on inside the machine, and what parts I would need. Also: The repair videos were critical for me to be able to ensure I was reassembling everything correctly. Shout out to Simon, who was featured in several of the repair videos. His "gorgeous... Read more

• Burning smell
• Will not agitate
• Pumps but will not spin

I pulled the unit away from the wall and noticed black dust on the floor. Unplugged the unit, turned off the water. Removed back panel (about 10 screws with Torx heads) and noticed the belt was off, the drive pulley was loose and wobbling on the shaft, black dust all over the inside. Belt was worn along one side. Some grooves/damage in the outer drum casing around the pulley where it appeared the belt had rubbed. Removed the lower crossbar (2 more screws) to get better access to the drive... Read more

This repair was performed on a Whirlpool Cabrio clothes washer Model # WTW5640XW0 which has the digital electronic controls rather than the older style timer, electro/mechanical controls. This washer was made in 2010. Simply having the diagnostic programs on this machine is wonderful and they work remarkably well and led me to the shifter/rpm sensor component straight away. It was a simple replacement by tipping the washer onto its front and accessing through the bottom. The machine was put... Read more

• Leaking

First, DO NOT call Sears for parts, their call center knows nothing about the product. App-Pros are the best for help and the right parts. I figured to repair, replace all seals and any item that shows need to and all items that have to do with the spin that may be bad. Repair videos great help. I will start from the "bottom" up, the repairs were not done in this order, just a list of what I did and notes. Replaced-- motor drive coupling, (checked out transmission ok), thrust washer,... Read more

This repair was performed on a Whirlpool Cabrio clothes washer Model # WTW5640XW0 which has the digital electronic controls rather than the older style timer, electro/mechanical controls. This washer was made in 2010. Simply having the diagnostic programs on this machine is wonderful and they work remarkably well and led me to the shifter/rpm sensor component straight away. It was a simple replacement by tipping the washer onto its front and accessing through the bottom. The machine was put... Read more

I started with the suspension pad kit and the tub suspension pads. I do have to say if you have an older model washer (mine is approx 17 years old) be prepared to let the inner tub sit in penetrating oil for a few days before attempting to take the tub out. I was able to get to this point on my own and then it wouldn't budge. My husband ended up buying some direct drive tool (it was pretty cool) and was able to break the tub free after two days. Yay! From there he took the the inner tub and put... Read more

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

• Will not fill with water
• Will not stop filling with water

The F20 code was low/no water pressure code. I watched a YouTube video and purchased a Water Inlet Valve from Appliance Pros. After my son installed the new part my washer still didn't work. I looked on Google for trouble shooting and the 1st thing it said was turn on both hot/cold water as the washer needs the pressure of the hot/cold water. I had turned off the hot valve because it was leaking. I assumed I could still do cold water loads. Read more

OK this is one of those stories that can't help but encourage those of us who have absolutely no idea how appliances work and yet by simply refusing to pay such ridiculous repair prices can honestly get it done with a "FRACTION" of the cost. So here is my story & the scary unknown(s) BUT the incredible help offered to me to successfully win the ( I won't allow you to take advantage of me ) anymore conclusion. I had a 2 1/2-year-old Maytag coin wash machine that just quit working; after... Read more

Installed new pump Read more

Rebalanced the load but noticed the drum was sitting lower and the springs were wore out and it went out of balance easy, so i got the suspension rod kit and installed it and it works much better. It took me 2 hours because i didnt have adequate room to move around. Hour job if you have room. Read more