Craftsman Parts

The shave plate is a common snowblower part that attaches to the back of the blower housing and directs snow into the auger and blade assembly so it can be cleared. The particular layer of ice and snow this blade is removing is the hardest and heaviest part of the snowfall. The shave plate is also called the scraper bar or scraper blade. Periodically, because it is in direct contact with the concrete surface below the snow, the shave plate wears out and must be replaced. A shave plate may be worn, gouged, or sliced so it does not smoothly remove the snow from the sidewalk. Replacing the shave plate is a simple task that can be accomplished in 30 minutes or less. The shave plate is connected to the blower housing by four adjustable fasteners that are removed. This genuine OEM replacement part is manufactured by Genuine MTD. It is compatible with a great variety of snowblowers, including Husky, Troy-Bilt, Yard Machines, MTD, Cub Cadet, and Yard-Man. This OEM part is sold individually.

Hinge pin fastener for lawn mowers. Secures moving components and panels. Replace if bent, missing, or damaged to restore proper attachment and function.

These O rings are replacement parts intended for use in a number of gasoline-powered lawn trimmers. The O rings serve as gaskets and are placed at the entry and exit points in the carburetors where gasoline and air are mixed and the expansion powers the trimmer. Though constructed of durable material, periodically the flow of the air/fuel mix or the rush of expanding air will cause damage to occur to the O rings so they become less resilient and the carburetor functions less efficiently. In these cases, users often decide to replace not just the element of the carburetor but the O rings as well. Users may notice problems with the carburetor when they cannot get an adequate adjustment, allowing the trimmer to function smoothly. They may also have trouble getting the trimmers to start at all or run without smoking. To replace the O rings, remove the air filter cover and carburetor. Once the carburetor has been cleaned, and the gasket and filter replaced, add a fresh mix of 40:1 fuel. The trimmer should start immediately. These OEM certified O rings are compatible with Bolens, Troy-Bilt, Yard Machines, and Craftsmen trimmers.

Engine won't start or runs rough? This spark plug creates the ignition spark for your tiller. Simple DIY fix when the electrode wears down over time.

This front bulkhead assembly forms the dryer's front drum support and air seal. Replacing a worn or damaged bulkhead restores smooth drum rotation, reduces noise, and helps maintain proper airflow for consistent drying performance.

• Supports and aligns the drum at the front to prevent rubbing and scraping
• Helps seal the lint/air path so heat stays in the drum and exhaust flows correctly
• Air leaks at the front bulkhead can contribute to long dry times or lint in the cabinet

• Disconnect power and gas supply and allow the dryer to cool before servicing
• Remove the front panel/door assembly; support the drum before detaching the old bulkhead
• Transfer any model-specific components from the original bulkhead and ensure seals/glides are correctly positioned
• After installation, rotate the drum by hand to verify clearances, then reassemble and test

Mower won't start even with brake engaged? A faulty interlock switch blocks current to the starter. This safety switch replacement restores starting function.

Replace your lawn mower's side discharge chute if it's cracked, broken, or missing. Attaches to the side of the mower to direct grass clippings away.

Metal blade adjuster rod for edgers. Sets blade position for bevel cutting. Replace if bent, damaged, or missing to restore blade angle adjustment.

Deck belt cover for riding mowers with 42-inch decks. Shields the belt assembly from debris and damage. Replace if cracked, broken, or missing.

Scraper blade installs at the base of your snow blower housing to clear snow down to pavement. Replace if worn, cracked, or missing bolts are exposed.

Water line kit for connecting ice makers to household water supply. Includes copper tubing, valve, and fittings for installation under kitchen sink.

Seals between carburetor and engine block to prevent air and fuel leaks. Replace if engine runs rough, leaks gas, or loses power. Verify fit by model.

Air cleaner housing protects the air filter from debris and damage. Replace if cracked, warped, or damaged to maintain proper filtration. Verify fit.

Hex head self-tapping screw for outdoor power equipment. Securely fastens components throughout your machine. Replace if missing, stripped, or worn.

Connects the cutting blade to the drive shaft on push mowers. Replace if adapter is chipped, cracked, worn, or loosened to restore secure blade mounting.

Replacement skid shoe for snow blowers. Mounts to the side of the auger housing to protect surfaces and control clearing height. Replace when worn.