Crosley Washer Support Parts

Our Maytag top load washer developed a bad slam during the spin cycle. Bad enough to shake the whole washing machine and make it move across the floor, sounded like it was going to destroy itself you could hear this thing in the furthest room in the house mind you it is on the opposite end of the house in the basement. For a while, you could do certain things to stop the issue or improve it, as you would expect that stopped working. I made sure the washing machine was level which I had to... Read more

After looking up the model number of my washing machine on AppliancePartsPros.com I ordered the suspension rod kit, two sets of tub centering springs (one spring per corner), a Ring-Tub (mine was breaking apart due to banging around) and a spare suspension bearing kit in case I need it later. I spoke to a very helpful customer service rep on the phone just before placing my order. They have customer service representatives answering the phone late at night. I was surprised. All of my parts were... Read more

Replaced suspension springs/rods and all associated bushings in the kit. Read more

After looking up the model number of my washing machine on AppliancePartsPros.com I ordered the suspension rod kit, two sets of tub centering springs (one spring per corner), a Ring-Tub (mine was breaking apart due to banging around) and a spare suspension bearing kit in case I need it later. I spoke to a very helpful customer service rep on the phone just before placing my order. They have customer service representatives answering the phone late at night. I was surprised. All of my parts were... Read more

First went through the troubleshooting guide on the website and read the various stories and watched the repair videos for replacing the springs and suspension pads. Then before ordering any parts disassembled the machine only to the point of removing the cabinet to see if there were any obvious issues. The springs appeared OK but I couldn't tell of they were fatigued or not and all were in place but the tub suspension pads were definitely worn out. I then put the machine back together and went... Read more

Replace suspension rods. Read more

• Shakes and moves
• Noisy
• Pumps but will not spin

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

Replaced suspension rods. Read more

First went through the troubleshooting guide on the website and read the various stories and watched the repair videos for replacing the springs and suspension pads. Then before ordering any parts disassembled the machine only to the point of removing the cabinet to see if there were any obvious issues. The springs appeared OK but I couldn't tell of they were fatigued or not and all were in place but the tub suspension pads were definitely worn out. I then put the machine back together and went... Read more

• Shakes and moves
• Noisy

I watched the video posted by Jerrod Sessler on yellow van handyman.com. Then I had to unstack the dryer from the washer, remove all covers, disconnect all hose connections, shock mounts and springs and remove the tub assembly. Then I disassembled the tub assembly and remove seal and both bearings from the rear half. At this point I cleaned everything. I installed new bearings and seal, installed the basket and assembled both tub halves using a new gasket and silicone, and reinstalled the... Read more

Rebalanced the load but noticed the drum was sitting lower and the springs were wore out and it went out of balance easy, so i got the suspension rod kit and installed it and it works much better. It took me 2 hours because i didnt have adequate room to move around. Hour job if you have room. Read more

Replaced all 4 shocks. Read more

Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more

I tore it apart using. YouTube videos to guide me and found the shocks were loose and floppy. I found the shocks in stock here and had them in my hand 2 days later for only $10 shipping! It runs great now! Read more

I ordered a tub suspendion Kit for it. Read more