Dishwasher Support Parts

The Dishrack Track (Right) is an OEM part for Whirlpool dishwashers. It is responsible for supporting the third-level dishrack and allowing it to glide in and out smoothly during the loading and unloading process. This track is designed specifically for the right side of the third-level rack. 

Causes of a bad track include damage from heavy use over time, such as dulling or bending of the metal track surface from repeated loading/unloading of dishes. Debris or residue buildup along the track can also cause issues.

Symptoms of a bad track include:  

• Rack that will not fully extend or retract
• Binding or sticking during rack movement  
• Rack that will not stay positioned above

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This adapter plate is a molded interface in the wash system that secures and seals components so water pressure is routed correctly. Replacing a cracked or warped plate helps stop leaks and restore proper spray performance.

• Connects and supports wash-system components at the sump/water-feed interface
• Maintains a reliable seal to help prevent leaks
• Helps direct wash water to the spray arms for effective cleaning
• Replace if cracked, warped, or stripped; symptoms can include leaks, weak spray, or a loose spray arm

• Disconnect power and water supply before servicing
• Remove the lower rack and related wash components to access the plate; note the order of parts for reassembly
• Reuse existing seals and fasteners in their original positions; seat the plate evenly and tighten hardware snugly, not overtight
• Run a brief test cycle and inspect for leaks before full use

This dispenser water tube routes water from the inlet to the refrigerator's in-door dispenser manifold, helping ensure a steady, leak-free flow to the dispenser.

• Directs water from the supply line to the dispenser manifold
• A damaged or cracked tube can cause leaks, low/erratic dispenser flow, or air in the water line
• Replacing a leaking tube can help restore normal dispenser operation and prevent water damage

• Unplug refrigerator and shut off water supply before service
• Have a towel/container ready to catch residual water
• Note tube routing and connections; push-to-connect fittings may require firm seating for a watertight seal
• After installation, turn water on and check all joints for leaks

The Upper Spray Arm Support is an OEM replacement part for GE dishwashers. It is installed within the dishwasher tub below the upper spray arm, and is responsible for securely mounting and holding the upper spray arm in place during operation.

Symptoms of a bad upper spray arm support include:

• Vibration or noise from an unsecured spray arm
• Improper alignment of water spray pattern  
•  Restricted rotation of the spray arm during washing
• Leaks at the tub connection point

Causes of a bad spray arm support can be from cracks or breaks that compromise its structure, or wear over extended use without replacement. 

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This thermistor holder secures the temperature sensor in place inside the dishwasher, ensuring accurate water temperature readings for proper wash and dry performance.

• Holds the thermistor securely in the sump/tub area
• Helps the control accurately monitor wash water temperature
• A loose or missing holder can cause temperature-related wash issues
• Common symptoms include temperature errors or poor cleaning/drying when the sensor isn't properly positioned

• Disconnect power and turn off water supply before servicing
• Access the sensor location from the tub/sump area; note original orientation
• Transfer the thermistor into the new holder and snap the holder into place
• Inspect the sensor wiring and seals while reassembling

This left-hand (LH) support is the factory replacement bracket that secures and aligns the left side of its assembly, helping keep parts level and operating smoothly. Replacing a damaged support restores proper fit and reliable function.

• Provides structural support and alignment on the left-hand (LH) side
• Helps keep connected components level and properly spaced
• Common symptoms: cracked/broken support, wobbling or sagging parts, misalignment, rubbing or binding during use
• Typical causes: wear, stress/impact, overloading, or overtightened fasteners

• Disconnect power before servicing; shut off water supply if applicable. Wear cut-resistant gloves.
• Clear the area for access. Note the original orientation and retain any screws/clips for reuse.
• Install the new LH support in the same position and ensure it aligns with the opposite side.
• Check fit and operation before fully reassembling.

This hanger anchors the dishwasher's door-balance spring to the frame so the door opens and closes smoothly. Replacing a worn or broken hanger restores proper spring tension and helps prevent a door that drops, slams, or feels heavy.

• Secures the door balance spring to the dishwasher cabinet/frame
• Maintains correct spring tension for smooth, controlled door movement
• Helps fix a door that falls open quickly or won't stay in position
• Useful to replace when door balance hardware shows wear or damage

• Disconnect power and shut off water before servicing; remove the toe panel/kickplate
• Support the door and carefully relieve spring tension before removing parts
• Slide the dishwasher out if needed for side access; transfer the spring to the new hanger and reinstall
• Inspect the opposite-side spring/link and hinge for wear; verify door balance before reassembly

This mount secures the dishwasher's upper spray arm to its water feed, keeping the arm aligned and free to rotate so the upper rack receives consistent spray coverage and dependable cleaning.

• Supports and centers the upper spray arm at the correct connection point
• Helps maintain a solid connection to the feed tube/manifold for proper water delivery
• Wear, cracks, or looseness may lead to poor cleaning on the upper rack, arm wobble, or noise
• Replacing a damaged mount can help restore smooth spray arm rotation and wash performance

• Disconnect power and turn off water supply before servicing
• Pull out the upper rack; remove the upper spray arm from its mount
• Release the old mount's locking tabs or fasteners and remove it from the feed tube/tub
• Install the new mount fully, reattach the spray arm, and verify it spins freely before testing

The Rack Support (RH) is an OEM part for Whirlpool dishwashers. It is the plastic right-hand side bracket that secures the upper rack assembly inside the washer cavity. 

Causes of a damaged rack support include cracks or breaks from normal wear over extended use. Repeated impact from dishes loading/unloading can cause small stress fractures.

Symptoms of a faulty support include:  

• Loose or rattling upper dish rack during operation
• Difficulty sliding racks in/out smoothly
• Visible cracks or missing pieces on the support

This Whirlpool OEM part is also compatible with Maytag, Jenn-Air, KitchenAid, and some Kenmore models.

There is a split at the 3 O'clock position. Color: white. It measures about 3 inches wide by 4 inches high.

This water inlet hanger secures the appliance's fill tube or line in the correct position, supporting a proper fill path and reducing strain on fittings. Replace a cracked or missing hanger to prevent movement, vibration, and potential leaks.

• Supports and positions the water inlet tube/line or inlet assembly
• Helps maintain alignment and sealing at the connection point
• Reduces vibration and prevents rubbing/chafing against surrounding parts
• Common symptoms include a loose or sagging inlet, rattling noises, chafed tubing, or drips from a misaligned inlet

• Disconnect power and shut off the water supply before servicing
• Access the inlet area and note the original hanger orientation and routing
• Remove the damaged hanger and mount the new hanger using the existing mounting points/fasteners
• Ensure the tube/line is secure and not kinked; restore service and run a brief test to check for leaks

Dishwasher lower wash arm and spray tower support.

This upper dishrack track mounts to the dishwasher tub wall and provides a smooth glide path for the rack rollers. Replacing a damaged track restores easy in-and-out movement and helps keep the upper rack aligned and secure.

• Guides and supports the upper dishrack as it slides in and out
• Maintains rack alignment to prevent binding or derailing
• Typical failure signs: rack jams or falls off, rough/squeaky travel, visible cracks or breaks in the track
• Can keep the rack from fully sliding in, making the door harder to close

• Disconnect power and turn off the water supply before servicing
• Remove the upper rack by releasing the end caps/stops
• Unfasten the old track from the tub (screws/clips), then position and secure the new track
• Reinstall the rack and end caps; verify smooth rack travel before restoring power and water

This conduit assembly carries wash water from the pump to the dishwasher's tiered spray system for consistent rack coverage. Replace a damaged or clogged conduit to restore spray performance and minimize leaks or spray loss inside the tub.

• Channels water to the upper/tiered spray jets for proper coverage
• Helps maintain correct flow and spray pressure to the upper wash system
• Common symptoms: poor cleaning on the upper rack, weak/no spray from upper jets, or leaks/spray from the rear conduit area
• Visible cracks, warping, or broken tabs can prevent a tight, leak-free seal

• Disconnect power and shut off the water supply before servicing
• Remove racks as needed; release interior screws/tabs to detach the conduit and note original orientation
• Seat all connections and seals fully to prevent leaks; secure mounting points
• Run a short test cycle and check for leaks and proper spray action

This hub mounts on the pump outlet to secure and center the dishwasher's lower spray arm, allowing smooth rotation and even water distribution for consistent cleaning on the bottom rack.

• Anchors the lower spray arm to the pump/sump assembly
• Provides the pivot point so the arm spins freely
• Helps channel wash water into the spray arm
• Typical symptoms: arm not spinning, poor cleaning on the lower rack, wobbling/falling arm, scraping or grinding at the hub

• Disconnect power and water supply before servicing
• Remove the lower rack; lift off the spray arm and any retainer/screw if present
• Remove the old support from the pump outlet; seat the new support fully; reinstall the spray arm and fastener
• Verify the arm spins freely and clears obstructions; run a short test cycle to check operation

Also Order Spray Arm Seal