Need Help?
Call or text
Replacement rail for dishwasher upper dishrack. Installs inside tub to guide rack sliding. Replace if cracked, bent, or causing rack to fall off track.
Replaced four rollers & slide. Read more
Roller bearing cage installs in the dishwasher rack track to support smooth gliding. Replace if cracked, broken, or causing the rack to stick or slide out.
I did not see the old ones fall out, so I was not sure the exact product placement within the rail, which was frustrating, to say the least. For the next person's benefit....these slide into the MIDDLE of the rail that is attached to both sides of the dishwasher. Not the front, not the back, but the middle! Steps to fix: 1) Order 2 of these Roller Bearing Cage. 2) Order 4 of WD12X10304 (AP4484666) end caps!! Unless you have brand new ones already, you will need them for sure and they are... Read more
The Track Assembly is an OEM replacement part for Whirlpool dishwashers. As the guide rail that the lower rack rolls along, this track plays an essential role in properly positioning dishes within the unit. Causes of a faulty track can include normal wear from extended use, damage from heavy loads or impacts, or failures of the mounting brackets. Symptoms of a bad track include:
This Whirlpool OEM part is compatible with additional appliance brands including Maytag, KitchenAid, and Jenn-Air.
Easy project. 6-year-old appliance. If one is failing replace all 4. The plastic race that holds the bearings becomes brittle and breaks dropping the bearings into the dishwasher tub. Total project time from assembling tools, protecting the hardwood floor, removal, and installation was less than 2 hours. 1) Turn off power to the appliance. 2) Remove 2 mounting Phillips screws holding dishwasher in the cabinet. 2) use a 1/4” nut driver to remove the 2 screws holding the bottom plate from... Read more
Left-hand track assembly for dishwasher lower rack. Guides rack smoothly in and out. Replace if broken, cracked, or worn plastic race causes instability.
The lower basket L& R track bearing brackets on my KitchenAid dishwasher (KDTE704DSSO) finally gave out (ball bearings everywhere) after (6) years of daily, family use. The service techs provided me with all the information I needed to successfully and quickly complete my project. My parts were mailed to me very quickly and my dishwasher was up and running in short order. The parts were clean and in perfect working condition. (After pulling your dishwasher out, there are two sets of screws on... Read more
Right-hand dishrack support bracket mounts to the interior side wall of your dishwasher tub to stabilize the upper rack. Replace if cracked or broken.
Removed the bottom rack from the dishwasher. Removed the 2 front plates at bottom of the dishwasher. Removed the two screws from the top of the dishwasher holding the dishwasher to the counter-top. Pulled the dishwasher out. Removed the 8 mm screws from the outside of the dishwasher-- 4 per side (Underneath the sound proofing). Pulled the old tracks and placed the new tracks into place and tightened the screws back up. Pushed the dishwasher back into place. Reinstalled the screws securing... Read more
The Manifold is an OEM part for Whirlpool dishwashers. Located in the dishwasher base, it directs water flow to the primary wash and rinse arms during cycles.
Causes of a bad manifold include mineral deposits clogging internal valves over time, worn seals no longer containing water as intended during rinse and wash, or broken diverter components.
Symptoms of a failed manifold are:
It is also compatible with KitchenAid, Jenn-Air, and some Maytag dishwashers.
No tools required. One item was defected but Appliance parts replaced it immediately. Read more
Holds and stabilizes the spray arm assembly so it sits level and secure. Replace if cracked, broken, or worn to restore proper alignment in your dishwasher.
Replaced dishwasher spray arm, spray arm support plate, dishwasher drain trap filter assembly. Read more
Left-hand dishrack support mounts to the rack assembly to hold it level and guide smooth travel. Replace if cracked, broken, or worn to restore alignment.
Secures the spray arm to the dishwasher rack, allowing proper rotation during wash cycles. Replace if cracked, broken, or missing to restore spray arm.
We bought replacement parts from you and my daughter fixed it. It is working now. It would have been nice if all the parts came in a set. Read more
Provides structural stability for the upper wash arm in your dishwasher. Replace if cracked, broken, or worn to restore proper rotation and support.
I contemplated replacing it but was able to find all the parts right here and fix it within an hour. Now it works great with no leaks. I have been using AppliancePartsPros.com to maintain all my appliances as it has saved me thousands of dollars over the years. Read more
Replaces sliding rails that support and guide the upper dishrack along tub sidewalls. Needed when rails are cracked, worn, or broken causing binding.
I only needed a flat head screwdriver to remove the clips holding the parts in. It took all of 10 minutes and the dish washer is running great now. Read more
Secures the upper spray arm assembly in the dishwasher tub. Replace if cracked, broken, or worn causing the spray arm to droop or become misaligned.
Replaced wash arm mount Read more
Covers and protects the dishwasher pump assembly. Replace if cracked, broken, or if plastic guides are stripped causing spray arm support issues.
The cover was easy to remove with 3 star head screws. I entered my model number on AppliancePartsPros.com dreading the cost I was about the encounter. However, the parts were very cheap, in stock, and shipped within an hour of my order. I had a question about the tracking number and received an email back in less than an hour. The cost for both parts and standard shipping was under $30. Once I received the parts, the new cover was installed, the rest of the assembly was put back back... Read more
Mounts the mid-level spray arm to its supply tube. Replace if cracked, worn, or broken to keep the spray arm centered and spinning freely on the rack.
The middle sprayer sheared off our GE Power 3 dishwasher, ruining the hub in the process. We removed the rack from the dishwasher to make it easier to access the sprayer hub, otherwise it's awkward. The biggest challenge was finding the right tool in our garage (we used a 1/4" wrench as we did not have the right socket size). Once the screw was removed, it was quite easy to remove the hub and attach the new one. The rest was simply attaching the new sprayer to the hub using the included... Read more
Secures the middle wash arm manifold tube in your dishwasher. Replace if cracked, broken, or split from age or heat damage. Installs on manifold tube.
Part was exact item. Easy repair. Read more
The Dishrack Track (Right) is an OEM part for Whirlpool dishwashers. It is responsible for supporting the third-level dishrack and allowing it to glide in and out smoothly during the loading and unloading process. This track is designed specifically for the right side of the third-level rack.
Causes of a bad track include damage from heavy use over time, such as dulling or bending of the metal track surface from repeated loading/unloading of dishes. Debris or residue buildup along the track can also cause issues.
Symptoms of a bad track include:
This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.