Dryer Cap Or Cover

This small plug seals and finishes an unused factory or service hole on the appliance cabinet or liner. It restores a clean, finished appearance and helps keep dust and splashes out of the opening. What it does

• Closes an open hole on the cabinet/liner or panel
• Helps reduce entry of debris and incidental moisture into the opening
• Maintains a neat, finished look
• Replace if the original plug is missing, cracked, or won't stay seated

• 1 plug

• Disconnect power before servicing; shut off water supply if working near water lines
• Identify the correct opening per your model's parts diagram
• Remove any remnants of the old plug; clean the area
• Align and press the plug fully into the hole until it sits flush—do not force or deform the panel

The Filter Housing is an OEM part for Whirlpool dryers. As part of the dryer ventilation system, the filter housing holds the lint filter in place, trapping lint and debris before it exits through the vent. It helps prevent blockages in the exhaust vent and surrounding area.

Causes of a bad filter housing can include cracks, breaks or defects in the plastic material over time due to normal use and heat exposure inside the dryer. Increased wear and tear from extended use can also cause damage.

Symptoms of a bad filter housing include:

• Excessive lint building up inside the dryer
• Reduced air flow and inefficient drying times
• Strange sounds like vibrations or rattling coming from the vent area
• Lint escaping from gaps in the filter housing

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

A replacement outer access cover that protects internal components and keeps the appliance appearance finished. Restores a secure barrier over openings to prevent debris and accidental contact with internal parts. What it does:

• Shields interior components from dirt, dust and spills
• Prevents accidental contact with wiring or moving parts
• Stops drafts or light from entering the cabinet opening
• Eliminates rattles or vibration caused by a cracked or loose cover

• One replacement outer access cover

• Disconnect power (unplug or shut off breaker) before starting any repair
• Remove adjacent panels or fasteners as needed to access the cover; basic hand tools usually required
• Handle edges carefully to avoid scratching the finish; align tabs and secure all fasteners

Replacement heat pump access door that covers and protects the heat pump compartment while restoring the appliance's finished appearance. Fits the original opening and provides safe removable access for service and maintenance. What it does:

• Covers and protects heat pump components from dust, debris, and accidental contact.
• Restores a sealed, finished look to the appliance exterior.
• Allows authorized service access when removed for diagnostics or repairs.
• Use when the original door is cracked, warped, missing, or no longer secures properly.

• Disconnect power to the appliance before attempting removal or installation.
• Designed to install with the appliance's original clips or screws; follow your model's service manual for exact procedure.
• Handle retaining tabs and edges carefully to avoid breaking mounting clips.
• If mounting hardware is missing or damaged, retain original fasteners or order appropriate replacement hardware.

This snap-in hole cap covers and seals an unused opening on the appliance cabinet or control panel to restore a finished look and help keep out moisture and debris. Simple cosmetic repair that prevents dirt buildup and accidental contact with interior components. What it does:

• Covers an exposed hole or access opening for a neat, finished appearance
• Helps keep out dust, crumbs and light moisture from entering the cabinet
• Reduces risk of accidental contact with interior parts through an open hole
• Restores factory look after removing a screw, plug, or accessory

• One snap-in hole cap

• Snap into the hole from the exterior until fully seated; minimal force required
• Use a plastic trim tool or small flat blade carefully if needed to pry out old cap
• Disconnect power or follow appliance-specific safety precautions before accessing internal areas
• Replace if cracked or deformed

The Lint Filter Cover is an OEM part for GE electric dryers. It securely houses the crucial lint screening component located inside the dryer drum.  

Symptoms of a bad lint filter cover include:

• Cracks, breaks or holes compromising the seal around the lint filter
• Loose, missing, or improperly closing attachment points
• Excess lint buildup bypassing the filter into the surrounding cabinet

Causes involve dried-out or fatigued clips, hinges, and seals from repeated use over cycles. Cover failure risks fire hazards from obstructed airflow.

This GE OEM replacement lint filter cover ensures safe, snug-fitting protection of the integral screen. Compatible with some Hotpoint and Kenmore dryers as well, it maintains ventilation and fire prevention. 

The Cover is an OEM part for Bosch dryers. It provides an additional seal over the removable lint filter compartment inside the dryer cabinet.

Causes of a bad filter cover can be general wear and stress from repeated removal and replacement of the lint filter over extended use. Heat cycling during drying may also cause plastic material fatigue and impact integrity.

Symptoms of a bad dryer filter cover include:

• Cracks, warping or holes in the material compromising the seal
• Inability to properly protect the internal lint filter from accumulation
• Excessive airflow and circulation that impacts drying efficiency

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.