Dryer Cap Or Cover

Protective cover that secures over the lint filter housing. Replacement needed when cracked, broken, or missing to keep debris out and ensure proper fit.

White plastic cover that snaps over the lint screen opening. Replace if cracked, broken, or missing to protect laundry from falling into the compartment.

Trim piece that conceals the door hinge and mounting screws. Replace your cracked, broken, or missing hinge cover to restore a clean finished look.

The Cover is an OEM part for Bosch dryers. It provides an additional seal over the removable lint filter compartment inside the dryer cabinet.

Causes of a bad filter cover can be general wear and stress from repeated removal and replacement of the lint filter over extended use. Heat cycling during drying may also cause plastic material fatigue and impact integrity.

Symptoms of a bad dryer filter cover include:

• Cracks, warping or holes in the material compromising the seal
• Inability to properly protect the internal lint filter from accumulation
• Excessive airflow and circulation that impacts drying efficiency

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Reversible door plug fills unused mounting holes when switching refrigerator door swing direction. Replaces broken or missing plugs for a finished look.

This fuse terminal cover shields and insulates the fuse connection inside your appliance, helping prevent accidental contact and shorting. Replace a cracked or missing cover to maintain safe electrical protection and dependable circuit performance.

• Covers and insulates the fuse terminals to protect the connection
• Helps prevent accidental contact, arcing, and debris intrusion at the fuse
• Common signs you need this part: missing cover, cracks, heat discoloration, or a cover that won't stay secured
• Promotes a secure, consistent fuse connection once installed

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the fuse area per your service information; note wiring and cover orientation
• Remove the damaged cover; inspect terminals and wiring for heat damage or looseness
• Seat the new cover fully and verify it is secure and clear of wiring

Replacement filter cover that secures your dryer's lint filter inside its housing. Installs quickly to replace a cracked, broken, or missing cover.

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Protective cover shields internal wiring and electrical terminals in your dryer. Replace if cracked, broken, or missing to prevent accidental contact.

Protective cover that shields the rear power connection terminals on your dryer. Replace if cracked, broken, or missing to prevent lint buildup and accidental contact with electrical connections.

This replacement cover restores the appliance's finished appearance and protects internal components from dust and debris. It's a direct-fit exterior trim piece designed to replace a cracked, broken, or missing cover. What it does:

• Protects internal components and wiring from debris and accidental contact
• Restores the appliance's cosmetic appearance and helps maintain sealing
• Helps reduce dust buildup in the covered area
• Replaces damaged or missing trim that can expose sharp edges or hardware

• Disconnect power (unplug or switch off circuit breaker) before beginning work
• Basic hand tools may be required; follow for panel removal/replacement
• Handle carefully to avoid scratching the finish and watch for sharp edges
• Replace with manufacturer-recommended fasteners

This replacement door restores a secure close and proper sealing for your appliance. Replacing a damaged or misaligned door helps ensure safe operation and correct latch/switch engagement for reliable everyday use. What it does:

• Provides the closing barrier for the appliance cabinet to maintain proper containment (heat, air, steam, or moisture as designed)
• Aligns with hinges and latch/door switches for correct interlock and operation
• Helps prevent leaks and drafts and protects the interior from damage
• Can address issues such as difficulty closing, visible cracks/dents, poor sealing, or the unit not starting/stopping when the door is moved

• Includes 1 door

• Disconnect power before servicing; also shut off gas or water if applicable
• Support the door during removal/installation; a second person may be needed for larger/heavier doors
• Transfer any reusable hardware (hinge pins, screws, nameplate/trim) from the original as needed
• After installation, verify alignment, latch engagement, and seal/gasket contact; test operation

• Finish, handle style, and configuration are model-specific—ensure the correct match

This protective cover shields and guides the appliance's water line at the back, helping prevent kinks, abrasion, and vibration. Replacing a damaged or missing cover helps protect the tubing and supports consistent water flow. What it does:

• Protects and routes the water supply tubing to reduce rubbing and wear
• Helps prevent kinks or pinches that can restrict water flow
• Keeps the line secured to minimize vibration and rattling
• Common signs include a cracked/missing cover, exposed/kinked tubing, leaks, or reduced water flow

• 1 water hose cover

• Disconnect power and shut off the water supply before servicing
• Pull the appliance forward for access; remove any screws/clips securing the old cover
• Note the tube routing; install the new cover without pinching the line
• Restore water and power, then check for proper flow and any leaks

Replacement outer housing cover for dryers. Restores finished appearance and shields internal components. Needed when original is cracked or damaged.

Exterior housing cover that holds and protects your dryer's lint screen. Replace if cracked, broken, or missing to restore proper lint containment.

Seals unused factory or service holes on your dryer cabinet or liner. Restores a clean appearance and keeps dust out. Replace if cracked, broken, or missing.