Dryer Parts

Replaced timer Read more

• Shuts off too soon

Replaced heating element about three months ago. Had to order thermistor because of error code "ts" on display and dryer would not run. Removed the two screws on the back that holds the top in place. After removing the top, remove the screws that hold the control panel on front. Make sure not to break the tabs that help hold it in place You do not have to unplug any connectors for the control panel. Lay control panel across top of dryer carefully so that it will be out of the way. Next... Read more

Easy fix, first I unplugged the dryer. Then removed the 6 Philips head screws on head unit back panel. Photographed wiring on timer. Removed the 1 torx screw holding the timer assy in place, the front panel knob was already off, would no longer stay on. Removed the wires from the timer assy, removed the timer, replaced it with new one, reinstalled torx screw. Reattached the wires to the positions removed from. Pressed the new knob on the shaft at front panel, tested it functioned and in the... Read more

• Element will not heat

I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help. Read more

Replaced back splash on dryer, repair took 5 minutes Read more

Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more

• No heat or not enough heat

Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in... Read more

Simple unplug, unscrew and replace. Read more

• Won't start

1) Ordered part. 2) Removed front panel by loosening the two screws at the bottom front. 3) Removed old Safety Switch/Lid Lock by disconnecting wires (plug and 2 female disconnects) 4) Reconnected all wires and reinstalled switch. 5) Replaced front panel. 6) Tested Unit. 7) FYI - I found that the locking mechanism stays locked until cycle completely finishes on its own. DO NOT force the cycle to end. Lid will NOT unlock. Read more

• tripping breaker

Starting circuit in motor bad. Replaced motor works fine. Read more

Chatted with 1 of your professionals and within a minute she had the part and it was on it's way. The job was VERY easy to fix and the part is working great! Read more

I went on line and purchased all of the possible parts that could be worn out. I spent less than the service guy wanted to show up...The online videos were spot on. Two hours and it works like new! One of the best values on the Internet! Read more

Unfortunately my first repair attempt (replacing the Gas Valve Coils) failed so I decided to replace the entire Burner assembly. From a cost/time point of view the Burner assembly is a better value than just buying the Gas Valve seeing as you don't have to disassemble/reassemble most of the existing Burner (to get to the Gas Valve) *and* you get a new Igniter!! The most annoying thing about the repair is accessing the screw that clamps the gas pipe to loosen it :-(... Read more

Replaced door Read more

I replaced the idler pulley assembly, the bearing plastic and the drive belt. While disassembled I cleaned the interior of the cabinet and lubricated the drum bearings with silicone after cleaning everything thoroughly. The dryer is now quiet and hopefully stays that way. Read more

After reviewing various posts on the internet, I tested the high heat temperature limiter and determined it was faulty due to lint buildup. Ordered the parts from AppliancePartsPros.com on Friday afternoon and parts were delivered on Saturday afternoon. Replaced the parts- dryer works as good as new. Read more