Dryer Parts

After reviewing various posts on the internet, I tested the high heat temperature limiter and determined it was faulty due to lint buildup. Ordered the parts from AppliancePartsPros.com on Friday afternoon and parts were delivered on Saturday afternoon. Replaced the parts- dryer works as good as new. Read more

The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more

I went on line and purchased all of the possible parts that could be worn out. I spent less than the service guy wanted to show up...The online videos were spot on. Two hours and it works like new! One of the best values on the Internet! Read more

I replaced the thermal cut-off sensors and the cutoff-Tml Read more

I have a Bosch nexxt 500 series dryer that stopped heating. It was still running fine, just no heat. I did some research and found the Limiter as the possible problem. I pushed the red reset button. The dryer started heating up, but with in 1 cycle kicked off again. I called A.P.P. and spoke to Cecilia. She was very helpful. After a brief description of my situation she recommended just to replace the Limiter. I did so and that fixed the problem. Very simple replacement. It look longer to take... Read more

I have order three parts, guide filter, cover guide, and sensor assembly. My previous cover guide was from two parts, when sensor assembly was one of them. New part ( guide cover ) was all in one piece so I just transfer old metal part of sensor to new cover guide and I don't need that sensor assembly anymore. I have ordered all three parts overnight by Fedex, ordered 15 min before 5pm, so next day it was here. Dryer is fixed, I'm happy. Read more

I fixed the problem by replacing the main control board Read more

Selected and ordered parts from online drawings. Watched videos showing how to make repair. Replaced worn parts with new ones. Suggested improvement: Videos didn't show my model (I know there are many models, showing all is probably not possible). In case of Felt the video showed a Maytag dryer when my model was GE. In my case Felt had torn and dislodge from slot so I didn't know exactly how it should be installed. A simple picture of the installed Item would help. Also the parts list should... Read more

I checked the continuity on the thermal fuse (which was blown) and knew that it needed to be replaced. This made me question why it blew (i.e. what caused it to fail). I checked continuity on the thermostat (high limit) as well as the thermostat for the element. Both passed a continuity test, so I removed the high limit thermostat to inspect it and could hear it rattling inside. This leads me to believe the spring inside had failed, so I replaced this thermostat as well. Put it back... Read more

Remove bottom panel, remove top panel, remove drum. Had to cut old squirrel cage off. Remove motor to remove old wheel shank. Remove belt switch, and replaced. Videos from AppliancePartPros helped a lot.. Read more

Troubleshot the oven by checking the broiler which worked good (same fuel valve). After reading the some tips about troubleshooting the Glow Ignitor I could see the broiler ignitor got white hot and the oven ignitor only got bright orange (orange to red causes intermittent ignition or mini explosions). Watched the how to video and it was good information. You should be observant about which openings in the back of the oven as to where the two wires are coming out of. My oven is over 12 years... Read more

• Will not tumble

Replaced front drum roller wheels and rear drum bearing.Pull plug. Remove 2 screws holding top panel,slide rearward and lift panel off. Remove all screws from back panel,wiring cover and cord clamp. Remove back panel and feed cord through hole.No need to remove cord. Remove 2 screws from heater box and let it drop rearward.Remove belt from motor pulley and let tensioner rest against motor pulley.This step will trigger the switch that disables motor if belt breaks.The switch does not reset... Read more

Replaced upper and lower felts. Painted rubbing surface on inside of drum with refrigerator enamel. Took out drum and lubed rear bearing. Replaced 2 of the 3 thermostats, and the belt just on principle. Spent a lot of time with shop-vac removing lint from drier and exhaust ducts. Runs great and is no longer cooking or staining clothes. Read more