Electrolux Cap Or Cover

This upper hinge cover protects and finishes the refrigerator door hinge area on the right side, restoring appearance and helping keep hinge components free of dust and debris. Designed as a direct replacement for the OEM right-side hinge cover. What it does:

• Covers the upper door hinge area to improve cosmetic appearance and hide hardware
• Helps keep dust, crumbs, and moisture away from hinge components
• Prevents accidental contact with hinge edges while opening and closing the door
• Restores the original look after hinge repairs or replacements

• One upper hinge cover for the right (RH) side, gray

• Disconnect power to the appliance or unplug before servicing to prevent electrical hazards
• Handle carefully to avoid scratching the finish; align clip/fastener locations before snapping into place

This replacement access cover restores the appliance's exterior protection and helps keep internal components shielded from dust and moisture. It provides a clean finished appearance and maintains safe operation when installed correctly. What it does:

• Replaces a damaged or missing access cover to protect internal parts from debris and accidental contact
• Helps prevent moisture and dust from reaching electrical and mechanical components
• Restores the appliance's finished look and secures components behind the cover
• Can resolve issues where a broken cover prevents safe use or proper panel alignment

• One replacement access cover

• Disconnect power (unplug appliance or switch off circuit breaker) before beginning any work
• Follow OEM disassembly steps for the specific model; keep fasteners and trim for reuse unless damaged
• Use appropriate tools and avoid forcing clips or tabs to prevent cracking the new cover

This bypass is a small electrical connector used to complete or reroute a circuit inside the appliance, restoring continuity so the unit can be tested or operated while diagnosing a faulty component. What it does:

• Provides a safe path to complete an electrical circuit when a component or sensor is removed for testing
• Helps verify whether a control or subsystem is causing an interruption in power or signal
• Can be used temporarily to isolate faults and confirm repairs
• Resolve symptoms like intermittent operation or no-response from a circuit while troubleshooting

• Disconnect all power to the appliance before installing to avoid shock or damage
• Intended for diagnostic or temporary use; replace failed components with correct OEM parts for permanent repair
• Follow the appliance wiring diagram and manufacturer's instructions
• Ensure secure, insulated connections to prevent short circuits

This evaporator coil cover protects the refrigerator's evaporator assembly and helps direct airflow for more consistent cooling. It replaces a damaged or missing interior cover to keep the coil shielded and the compartment operating as intended. What it does:

• Shields the evaporator coil from contact and debris to prevent accidental damage
• Helps direct cold air across the evaporator for more even cooling performance
• Reduces unwanted airflow patterns that can cause frost buildup or uneven temperatures
• Covers sharp edges on the evaporator assembly for safer access during service

• One evaporator coil cover

• Disconnect power to the appliance before beginning any repair
• Remove interior panels and shelves as needed to access the evaporator area
• Handle the evaporator and cover carefully to avoid bending fins or damaging nearby components
• Fully defrost the evaporator before installing the new cover

This upper hinge cover protects and conceals the refrigerator's top door hinge for a finished look and safer edges. It restores proper appearance after damage or wear and helps keep the hinge area clean. What it does:

• Covers the upper door hinge to hide hardware and reduce dirt buildup
• Protects fingers and clothing from exposed hinge parts
• Restores cabinet appearance when the original cover is cracked or missing
• Works with the existing hinge assembly; does not affect door alignment when intact

• One upper hinge cover

• Designed to snap or slide into place over the upper hinge; may require removing the hinge trim or loosening the hinge for access
• Use basic hand tools; avoid over-tightening hinge fasteners after reassembly
• Disconnect power to the appliance if required for safe access to the hinge area
• Replace damaged components before installing the cover

This upper hinge cover is a small trim cap that restores the refrigerator's finished look and protects the hinge area from dirt and damage. It's a simple cosmetic and protective replacement for worn or missing hinge trim. What it does:

• Covers and protects the upper door hinge assembly from dust, spills, and everyday wear
• Restores a clean, finished appearance to the top hinge area
• Helps keep hinge fasteners concealed to reduce snagging and improve safety
• Commonly replaced when trim is cracked, faded, or missing

• One upper hinge cover/trim cap

• High-level replacement — typically snaps or screws into place; inspect fasteners before reinstalling trim
• Support the door while removing or installing hinge components to avoid shifting or dropping the door
• Unplug the appliance or turn off power to be safe when working near electrical components
• Wear gloves and eye protection to avoid cuts from sharp edges and to protect finish

This upper hinge cover hides and protects the refrigerator's upper hinge assembly for a clean, finished look and helps prevent clothing or items from snagging the exposed hardware. What it does:

• Covers and protects the upper hinge area from dirt and accidental contact
• Restores the refrigerator's finished appearance when the original cover is cracked or missing
• Helps reduce the chance of clothing or items catching on the hinge
• Simple cosmetic replacement that improves overall door area safety and cleanliness

• Support or secure the door before removing or installing hinge components to avoid injury or damage
• This cover typically snaps into place or is retained by the hinge fasteners; reuse existing screws or clips unless replacements are specified by the manufacturer
• Do not force the part into place; align with hinge mounting points and install gently

This upper hinge cover shields and conceals the refrigerator door hinge for a clean appearance and protected hinge area. It helps keep debris out of the hinge assembly and restores the cabinet's original look after repair or replacement. What it does:

• Covers the upper door hinge to protect the hinge pivot from dust and debris
• Restores finished appearance where the hinge is exposed
• Helps maintain smooth door movement by keeping the hinge area clear
• Is a direct-replacement exterior trim piece — useful when the original is cracked or missing

• One upper hinge cover

• Disconnect power or unplug the appliance before beginning work when applicable
• Remove food and items from the door to reduce weight before removing hinge fasteners
• Require basic hand tools (screwdriver or nut driver) to remove/install the cover or hinge fasteners
• Align cover over the hinge and secure; do not force or overtighten fasteners to avoid cracking the trim

This hinge cover protects and finishes the appliance's door hinge, restoring a clean appearance and helping keep the hinge area clear of dirt and debris. A simple cosmetic and protective replacement. What it does

• Covers and shields the door hinge to protect it from dust, grease and debris.
• Restores the appliance's finished appearance when the original cover is cracked, broken, or missing.
• Helps reduce the chance of exposed sharp edges from a damaged hinge area.
• A damaged or missing cover can contribute to visible hinge hardware and may make the door look misaligned.

• Support the door before removing any hinge hardware to prevent the door from shifting or falling.
• Handle edges carefully and wear gloves to avoid cuts from metal parts.
• Reinstall original mounting screws or clips; do not overtighten plastic components.