Electrolux Motor

This auger motor powers the ice dispenser, rotating the ice-bin auger to feed cubes or crushed ice to the door chute. A failed motor stops dispensing, leaving ice in the bucket when the paddle or lever is pressed.

• Drives the auger that moves ice from the bin to the dispenser chute
• Restores dispensing when the original motor is seized or burned out
• Common symptoms: no ice through the door, auger doesn't turn, motor only hums or clicks
• Note: Won't resolve issues from a jammed auger, frozen ice bucket, or broken drive parts

• Disconnect power before servicing; wear cut-resistant gloves
• Remove the ice bin to access the motor area as designed on your model
• Note wire orientation; transfer any reusable brackets or hardware from the original motor
• Align the drive interface and secure; test both cube and crush functions before reassembly

The Convection Fan Motor Kit is an OEM replacement part for Frigidaire ovens. This kit includes the motor responsible for driving the convection fan, which circulates hot air within the oven cavity to ensure even cooking and consistent temperatures during convection baking or roasting.

Over time, causes of a bad convection fan motor can include electrical wear, overheating due to heavy use, or damage from grease or debris buildup. Additionally, worn-out bearings in the motor can impair its performance.

Symptoms of a bad convection fan motor include:

• The fan not spinning or operating inconsistently  
• Uneven cooking results in convection mode  
• Strange noises such as rattling or grinding during operation  

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Note: Convection fan motor 5304467898 replaces earlier fan motors with a cooling blade. The fan motor doesn't include the cooling blade as it is no longer required.

This replacement motor restores reliable rotation to the component it drives—bringing back proper airflow or mechanical movement so your appliance runs as designed and noise is minimized.

• Converts electrical energy into steady shaft rotation to power the attached fan, blower, or mechanism
• Common failure signs: won't start, only hums, stalls, or intermittently runs
• Worn bearings or windings can lead to overheating and reduced performance

• Disconnect power before servicing; if the unit uses capacitors, discharge them per the service manual
• Note wire locations and transfer any brackets, grommets, or fan blades from the old motor
• Mount securely, align the shaft, and confirm correct rotation before finalizing
• Spin the shaft by hand to check for free movement, then test for smooth, quiet operation

This component is a drive motor that is made specifically for washing machines. The drive motor is what spins the tub and drives the agitator.If the washing machine fails to start or makes strange noises, it could be the drive motor that is causing the issue. Other signs that this part is faulty are if the washing machine fails to fill with water, agitate, spin, or drain. An error code reading “E57”, “E58”, “E59”, or “srv cll” may also appear on the digital display. Make sure to disconnect the appliance from its power source prior to attempting to replace this part. Whoever is performing the replacement may choose to wear gloves to protect their hands during this process.This drive motor is compatible with washing machines that are manufactured by Whirlpool, Kenmore Elite, Electrolux, Frigidaire, Crosley, and Kenmore. It is sold individually and sourced from the manufacturer itself.

This convection fan motor powers the fan that circulates heated air during convection cooking, helping your appliance maintain even temperatures and consistent results. Replacing a weak or noisy motor restores proper airflow and quieter operation.

• Drives the convection fan to move hot air throughout the cooking cavity
• Promotes even heat distribution for baking and roasting in Convection modes
• Activates when the control calls for convection airflow
• Common symptoms: fan not spinning, intermittent or slow operation, rattling or squealing noises, uneven cooking

• Disconnect power and allow the appliance to cool completely. Microwaves can retain dangerous high voltage even when unplugged.
• Access the motor behind the rear or interior fan cover per your model's design.
• Note wire positions; transfer the existing fan blade and any mounting hardware to the new motor if required.
• Ensure the fan spins freely before reassembly; restore power and test a Convection cycle.

This part is a genuine OEM replacement drive motor intended for use with dryer models. The drive motor works by rotating the drive belt, which in turn spins the dryer drum. A faulty motor could cause the drum to stop spinning altogether, or the user may notice a loud sound coming from the dryer when the drum tries to rotate. Work gloves should be worn, and the dryer should be unplugged from the power outlet before proceeding.This part was made by Frigidaire and has been sourced directly from the manufacturer. It is made out of high-quality, durable, non-corrosive materials to ensure the best possible durability. This drive motor is sold individually. It is intended for use with dryer models manufactured by Frigidaire, Electrolux, Gibson, Westinghouse, and other brands.

The Fan Motor is an OEM component for Frigidaire refrigerators. Located inside the refrigerator compartment, this specialized motor powers airflow and circulation through ducts within the cabinet.

Causes of a malfunctioning fan motor can include normal wear from constant operation, collecting debris that causes imbalance or binding, and motor winding failure over extended use.  

Symptoms requiring replacement are: 

• Reduced/insufficient air circulation within the refrigerator  
• Abnormally high temperatures or frost accumulation
• Loud buzzing or grinding noises emanating from the motor

This OEM part fits Electrolux, Gibson, Kelvinator and select Kenmore models as well for a direct fit. Replace promptly for dependable fan performance.

This replacement fan motor spins the appliance's fan to move air for cooling and circulation during operation. Replacing a worn motor restores proper airflow, helps protect internal components from heat, and can reduce noise from failing bearings.

• Drives the fan to move air through the appliance as designed
• Common fix for a fan that won't run or turns slowly
• Can help prevent overheating, hot control panel, or thermal shutdowns

• Disconnect power at the breaker or unplug the appliance; allow hot surfaces to cool
• Access point varies by model; remove panels to reach the fan motor
• Note wire positions; transfer the fan blade and any mounting hardware from the original motor if required
• Restore power and test

This motor drives the oven's convection fan to circulate hot air throughout the cavity for more even baking and roasting. Replacing a weak or noisy motor restores proper airflow and consistent cooking performance. What it does:

• Rotates the convection fan to move hot air uniformly across racks
• Helps maintain steady cavity temperatures during convection cycles
• Can resolve symptoms like a non-spinning fan, intermittent operation, or buzzing/grinding noises
• Improve uneven baking, poor browning, or extended cook times when convection is selected

• One motor

• Disconnect power at the breaker and allow the oven to cool completely
• Access the motor from the rear or through the oven cavity per your model's service procedure
• Note wire positions; transfer the fan blade and any mounting hardware from the old motor if required
• Ensure the fan spins freely by hand, secure wiring, then restore power and test convection operation

This motor powers the oven's fan to move air through the cavity or chassis, depending on the model. Replacing a weak or failed motor restores proper airflow, helping maintain stable temperatures and protect internal components during cooking and cool-down. What it does and common symptoms:

• Drives the oven's fan for cooling and/or convection airflow
• Fan does not run or starts intermittently
• Loud humming, squealing, or grinding from the fan area
• Control area feels unusually hot or oven struggles to maintain temperature
• Uneven baking performance when using convection (on applicable models)

• One motor

• Disconnect power at the breaker before servicing; allow the oven to cool
• Access is typically from the rear or top; remove panels to reach the motor
• Note wire locations and any rotation markings before removal; transfer any attached fan wheel/bracket as required
• After installation, rotate the fan by hand to check for clearance, then restore power and test operation

This fan motor drives your oven's convection fan, circulating hot air for even, reliable cooking performance. Replacing a weak or noisy motor restores proper airflow to reduce hot spots and improve convection baking and roasting results. What it does:

• Powers the rear convection fan to move air across the oven cavity
• Promotes more uniform temperatures on multiple racks during convection cycles
• Helps the oven maintain stable heat during use
• Common symptoms: fan won't spin, intermittent or slow rotation, loud humming/scraping from the rear, uneven results in convection mode

• 1 fan motor

• Disconnect power to the range or wall oven before servicing
• Access may require removing the rear panel or the oven's rear cover; note wire locations for reassembly
• Transfer the original fan blade and mounting hardware to the new motor; handle sharp edges and avoid bending the blade
• Spin the blade by hand to ensure free movement before restoring power

This replacement motor restores reliable rotation to the component it drives, helping your appliance circulate air or operate as designed. Replacing a worn motor can resolve no-start conditions, loud operation, and weak performance.

• Provides the rotational drive for the attached component, enabling proper airflow or movement
• Common failure symptoms include humming without turning, intermittent operation, seized shaft, or grinding/squealing noises
• Visual signs like burned windings, cracked housing, or excessive shaft play also indicate replacement is needed

• Disconnect power to the appliance before servicing; allow any moving parts to stop completely
• Photograph or label wire positions and transfer them to the new motor one-for-one
• Reuse existing mounting hardware and verify the motor and attached wheel/blade spin freely without rubbing
• After installation, restore power and test operation before final reassembly

This replacement motor restores the rotation your appliance relies on to move air or drive a mechanism, bringing normal operation and performance back when the original motor has failed or become noisy. What it does:

• Converts electrical power into controlled shaft rotation to drive the associated component
• A failing motor may cause no movement, intermittent operation, or unusual humming/grinding noises
• Can contribute to reduced performance if the driven part doesn't run as intended
• May present with overheating smell or visible signs of wear on the old unit

• One motor

• Disconnect the appliance from power before servicing
• Note wire locations and connector orientation; transfer any brackets, grommets, or hardware from the old motor
• Handle sheet-metal edges carefully; wear cut-resistant gloves
• After installation, confirm the shaft spins freely by hand before restoring power and testing

Evaporator fan motor that circulates cold air over the evaporator coil to help maintain even refrigerator temperatures. Replacing a failing motor restores airflow, reduces warm spots and frost buildup, and cuts down on excessive fan noise. What it does:

• Spins the evaporator fan blade to move cold air through the evaporator and into the cabinet.
• Promotes even cooling to prevent warm zones and food spoilage.
• Stops or reduces abnormal noises caused by a worn or seized motor.
• Helps prevent frost accumulation linked to poor airflow.

• Disconnect power to the appliance before beginning any repair.
• Handle the motor and fan blade carefully; ensure the fan blade is seated properly on the shaft.
• Remove evaporator/fan housing panels and retain screws and clips for reassembly; verify wiring connectors match before reconnecting.

A replacement evaporator fan motor that circulates cold air across the evaporator and through the fresh food and freezer compartments to help maintain even temperatures and consistent cooling performance. What it does:

• Powers the evaporator fan to move cold air through the refrigerator and freezer.
• Restores airflow when a failed fan motor causes uneven cooling or warm spots.
• Stops continuous frost build-up on the evaporator caused by poor or no airflow.
• Eliminates loud grinding, buzzing, or rattling noises coming from the freezer area.

• Disconnect power to the appliance before attempting any repair to avoid electrical shock.
• Access typically requires removing interior panels or the evaporator cover; keep track of screws and clips.
• Handle the fan blade carefully and test operation after restoring power.

This evaporator fan motor circulates cold air through the refrigerator and freezer compartments to maintain even temperatures and efficient cooling. A direct-fit replacement restores airflow and helps prevent warm spots. What it does:

• Spins the evaporator fan to push cold air across the evaporator coil and into the cabinet
• Helps maintain consistent temperatures in fridge and freezer compartments
• Commonly replaced when the fan is noisy, not spinning, or when sections of the refrigerator are warming
• Supports proper defrost performance by ensuring airflow over the evaporator

• One evaporator fan motor

• Disconnect power to the appliance before starting any work
• Access typically requires removing interior panels and the evaporator cover; follow your model's service instructions
• Handle the evaporator coil and fan blades carefully to avoid damage
• Test operation after installation and reassemble panels securely