Need Help?
Call
The Dispenser Cover Overlay is an OEM part for Frigidaire refrigerators. This part fits over the front of the dispenser, providing a protective and decorative cover for the control panel and dispenser mechanisms.
Causes of a bad dispenser cover overlay can include physical damage from impacts, wear and tear from frequent use, or fading and discoloration from prolonged exposure to sunlight and cleaning chemicals.
Symptoms of a bad dispenser cover overlay include:
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
So I ordered the face plate and other parts that went with it and fixed it myself. The repair man wanted around $600 to do it. I believe kt cost around $160 to fix it myself. Read more
Replacement cap for dishwasher detergent dispenser. Covers and seals the dispenser compartment. Replace if cracked, broken, melted, or missing.
Took cover completely off and tried putting back, could not match up left screw with available screw hole. Tried many different configurations and sequences to make this happen. watched a video on changing the front panel, the door in it had four screws, mine 2, no help there. Searched on the hyperextending issue, found an article about dogs and kids [had both here] climbing on the door and to check the springs and linkages. Linkages intact both sides, R [opposite] side spring very stretched.... Read more
Soap dispenser door won't open or latch is broken? This detergent dispenser assembly fixes dispensing failures. DIY repair takes 10-15 minutes.
This was a pretty easy fix. Removed the screws around the perimeter of the inside cover of the door and pressed the outer door cover upward to release it from slots retaining it. There are four wires to remove (2 for the detergent door release and 2 for the rinse agent release). Removed the 6 screws retaining the dispenser assembly and inserted the new one. Reassembly is simply in reverse order. Problem solved for less than the cost of a service technician's call! Read more
Controls ice and water dispensing from your refrigerator door. Replace if the module housing is cracked, broken, or if mechanical parts are worn or missing.
Replaced the broken dispenser with a new one. Read more
Fix a soap door that won't open or stay closed. This detergent dispenser releases soap at the right time during wash cycles. DIY-friendly repair.
Started with a YouTube video, then this site. Between the two, fixed in about a half an hour. Read more
Replacement actuator lever for refrigerator water dispensers. Installs on the exterior door panel. Needed when the paddle is cracked, broken, or missing.
I watched a video on YouTube that walked me step by step through the repair. Read more
Dispenser module housing for refrigerator doors. Holds valve assemblies, switches, and tubing for ice and water delivery. Replace if cracked or broken.
I ordered the new replacement housing and switched it out. Read more
Replace a cracked or broken dispenser cover to restore your refrigerator's appearance. Simple DIY repair, typically completed in 15 minutes or less.
Replaced with ordered cover and new screws. Cover was a perfect replacement for original. Replacement took less than 15 minutes to complete. Read more
The refrigerator dispenser cover module is an OEM part for Frigidaire refrigerators. This grey module serves as an aesthetic cover that helps protect the dispenser mechanism. It is designed to blend in with the exterior of the refrigerator sheltering its internal components.
Causes of a bad dispenser cover can include wear and tear over time, exposure to impacts or damage, or cracks that compromise its protective functionality.
Symptoms of a bad dispenser cover include:
This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
I found the exact same part on AppliancePartsPros.com. It arrived in just a few days and it fit perfectly. The replacement was easy and now the fridge looks great! Read more
Electronic dispenser module assembly for refrigerator doors. Controls water and ice dispensing functions. Replace if switches are unresponsive or broken.
REPLACED WITH YOUR MODULE. ARRIVED AS PROMISED & SAME AS OLD ONE. THANKS Read more
Plastic drip tray installs under the refrigerator water/ice dispenser to catch spills and drips. Replace if cracked, warped, discolored, or missing.
I removed the old one and put the new one in. It took about 1 minute. That is because I am counting the time it took from opening the package, removing the old dip tray and replace it with the new one Read more
Replaces the paddle lever you press to dispense ice or water. Install when the original actuator is cracked, broken, or worn for smooth operation.
Flipped the circuit breaker to turn the power to the fridge off. Had to remove the faceplate to the ice/water dispenser. Had to remove approx 16 screws and unplug the circuit board. Removed water tube (That was the hardest part) ! Had to disconnect and remove the broken part and reattach the new part. Then put everything back together again. Read more
Replace cracked or peeling dispenser cover label. Easy DIY fix—peels off like a sticker, alcohol wipe surface, press new label on. 10-minute repair.
Removed old label, took the glue residue off, wiped it down with rubbing alcohol then attached the new label on to the fridge. Read more
Covers and protects the dishwasher pump assembly. Replace if cracked, broken, or if plastic guides are stripped causing spray arm support issues.
The cover was easy to remove with 3 star head screws. I entered my model number on AppliancePartsPros.com dreading the cost I was about the encounter. However, the parts were very cheap, in stock, and shipped within an hour of my order. I had a question about the tracking number and received an email back in less than an hour. The cost for both parts and standard shipping was under $30. Once I received the parts, the new cover was installed, the rest of the assembly was put back back... Read more
Fix a broken or missing detergent dispenser cover that's cracked or won't guide proper detergent placement. Simple 5-minute replacement repair.
After examining it, 2 of the 4 retainer clips had broken off. My wife grabbed her tablet, found Appliance Parts Pros website, saw 2 videos featuring our exact model of washer and ordered the 3 parts to replace broken and soon to fail parts ! Shipping was extremely fast ! Took out old assembly, replaced with new assembly in about 15-30 second, wife was happy, therefore I was happy ! Thx for being there ! Read more
The refrigerator dispenser funnel guide assembly directs water and ice from the internal dispensing mechanism to the external outlet in the door. Located within the refrigerator door behind the dispenser area, it ensures proper flow and prevents spillage. Replace if water or ice dispensing becomes erratic, leaks occur around the dispenser, or the guide is cracked or clogged.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.