Frigidaire Heating Element

This replacement heater assembly restores proper heat output in your appliance. It delivers the thermal energy needed for normal operation so your unit can reach and maintain the correct temperature and complete cycles as designed.

• Generates heat for the appliance's heating/drying/defrost function (as applicable to your model)
• Helps the unit reach and maintain target temperature for proper performance
• Common failure signs: no heat or weak heat; cycles take too long or do not complete
• May trigger heating-related error/fault codes; visible breaks or hot spots on the element; tripped breaker from a short to ground

• Disconnect electrical power before servicing; allow hot components to cool
• Wear cut-resistant gloves; internal panels and chassis edges can be sharp
• Document wire routing and mounting positions before removal; route wiring exactly as original
• After installation, ensure secure connections and clearance from metal surfaces; run a brief test cycle to verify operation

The bake element is the lower oven heating element that produces heat during bake cycles. Replacing a failed element restores proper preheating and even baking performance when your range no longer heats correctly in bake mode.

• Provides bottom-up heat in bake mode to reach and maintain set temperatures
• Typical symptoms include no heat in bake, excessively long preheat, or uneven/undercooked results
• Visual clues of failure may include blisters, cracks, or burnt spots on the element
• A shorted element may trip a household breaker when energized

• Disconnect power at the breaker before servicing; verify no power to the range
• Remove oven racks; unfasten the element from the rear wall and gently pull it forward to access terminals
• Transfer the wires to the new element one at a time; do not let wires retract into the rear panel
• Reinstall and secure the element, ensure connections are fully seated and clear of metal, restore power, and test

Size: 8 inch. 2200 watt. Radiant.

This convection fan element mounts on the oven's rear wall around the blower. It supplies supplemental electric heat so the fan can circulate hot air evenly during convection modes for more consistent baking and roasting.

• Provides heat directly around the convection fan to help maintain even temperature during convection cycles
• Failure can cause poor browning, uneven results on multiple racks, or convection modes that run without proper heating
• May show visible breaks, blistering, or burnt spots; an open element will fail a continuity check
• If standard bake heats normally but convection bake does not, this element may be at fault

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks and the rear interior panel to access the element surrounding the fan
• Note wire positions; transfer any spacers or mounting hardware from the original element as needed
• Secure the element without bending it and confirm the fan spins freely with proper clearance

This oven heating element replaces a failed bake element to restore even, reliable oven heat for baking and roasting. It's a direct-replacement style part that heats the oven cavity when the bake function is used. What it does

• Heats the oven cavity during bake cycles so food cooks evenly
• Commonly used when the oven won't reach or hold baking temperatures
• Can fail visibly (broken or burned) or electrically (open circuit)
• Works with the oven's temperature control to maintain set temperature

• Disconnect power at the breaker before starting any repair to avoid shock.
• Handle the element carefully; connectors and terminals can be fragile.
• Confirm wire terminal fit and secure mounting; replace only with the correct OEM-style element.

This oven bake element is the heating element that warms the oven cavity for baking and roasting. Replacing a damaged element restores proper oven heating and helps return cooking performance to normal. What it does:

• Heats the oven interior for baking, roasting and browning.
• Replaces elements that are visibly burnt, cracked, broken, or no longer glow when the oven is on.
• Common symptoms it can fix: little or no heat from the oven, uneven cooking, or an element that sparks or shows burn spots.
• Works as the direct heater inside the oven cavity; connects to the oven terminal block.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Access typically requires removing the oven interior panels or rear access panel; support the element while disconnecting terminals.
• Handle terminals and sharp sheet metal carefully; use insulated tools and secure terminal connections.

This heater assembly restores heat production in electric dryers so clothes dry efficiently. It replaces a failed heating element and helps return the appliance to normal drying performance. What it does:

• Heats air passing through the dryer drum so laundry dries during operation
• Replaces a burned-out or open heating element that causes no heat or weak heat
• Addresses long dry times and extended cycles when the element isn't functioning
• Works with the dryer's blower and thermostatic controls to maintain proper air temperature

• Disconnect power at the breaker before starting any repair; this part carries live voltage during operation
• Handle the heating element carefully to avoid bending or damaging the coil
• Inspect fuses, thermostats, wiring, and connectors while replacing the heater to ensure full repair
• Follow the appliance manufacturer's service instructions for disassembly and reassembly

This replacement bake element heats the lower oven cavity so your range can bake and roast food at set temperatures. Restores normal baking performance when the oven isn't heating properly. What it does:

• Heats the oven's lower cavity to reach and maintain baking temperatures
• Replaces a burned-out, warped, or visibly damaged element
• Helps correct symptoms like no heat or uneven baking results
• Works with the oven control to provide consistent interior temperatures

• Disconnect power to the appliance before any service to avoid shock
• Handle element carefully; sharp edges and fragile terminals can be damaged
• Verify proper terminal connection and secure mounting during installation

This oven bake element heats the oven cavity so food cooks and bakes properly. Replacing a worn or broken element restores consistent heat for even baking and broiling. What it does:

• Converts electrical power into heat to warm the oven interior during bake and broil cycles
• Replaces a damaged or open element that can cause the oven to not reach temperature or cook unevenly
• Works with the oven's control system to provide steady, distributed heating
• Common symptom: oven won't heat, heats very slowly, or produces uneven cooking results

• Disconnect power at the breaker before starting any repair
• Allow the oven to fully cool and wear gloves to protect against sharp edges
• Remove the oven bottom or access panel as required, disconnect element wiring, and secure the replacement element in the original mounting
• Reconnect power and perform a short test bake to ensure proper operation

This bake element is the oven's primary heating element for baking and roasting, restoring proper oven heat so food cooks evenly. It replaces a damaged or worn element to bring back reliable bake performance. What it does

• Heats the oven cavity during bake cycles to provide consistent cooking temperatures.
• Commonly linked to symptoms like an oven that won't heat, takes too long to preheat, or produces unevenly cooked food.
• Visible damage (breaks, blisters, or heavy corrosion) or open electrical continuity are signs this element needs replacement.
• Works with the oven's control and safety systems to cycle heat as required.

• One bake element

• Disconnect power at the breaker or unplug the appliance before starting any work.
• Allow the oven to cool completely and handle the element carefully to avoid sharp edges.
• Inspect wiring and terminal connections; replace any damaged connectors before reassembly.
• After installation, restore power and run a short bake cycle to ensure proper operation.

This genuine surface coil element replaces a damaged or non-working burner on an electric cooktop to restore even heating for everyday cooking. It fits standard countertop ranges and reconnects to the existing socket for simple swap-outs. What it does:

• Heats cookware by converting electrical power into a cooking surface heat source
• Replaces a cracked, broken, or non-heating burner element
• Fixes symptoms like no heat from a burner, intermittent heating, or uneven cooking
• Works with the existing element receptacle and trim/reflector assembly when compatible

• Disconnect power at the breaker before attempting any service
• Allow the cooktop to cool completely and use gloves to avoid cuts
• Remove and retain any trim or mounting hardware; install using original screws/connectors

This oven bake element is the lower heating element that provides consistent radiant heat for baking and roasting. It restores the oven's ability to reach and hold baking temperatures for even cooking results. What it does:

• Heats the oven cavity from the bottom for baking and roasting
• Replaces a broken or visibly damaged element that won't heat or glow
• Helps correct uneven baking or failure to reach set temperatures
• Works with the oven's thermostat and controls to maintain cooking heat

• One lower/bake oven element

• Disconnect power to the range or oven at the breaker before servicing
• Access may require removing the oven floor or rear access panel; handle terminals carefully
• Inspect terminal connections and mounting hardware; tighten or replace as needed

Restore reliable heat with this replacement heating element. A worn or damaged element can cause long heat-up times, uneven temperatures, or no heat at all. Swapping it out helps return consistent, dependable heating performance.

• Converts electrical energy to heat when energized
• Common symptoms: no heat, slow to heat, or uneven/inconsistent temperatures
• Visual clues: cracks, breaks, burn spots, or terminals damaged/corroded
• Helps resolve heat-related error codes after proper diagnosis

• Disconnect power at the breaker before servicing; verify no voltage present
• Note wire positions and terminal orientation before removal
• Handle carefully; avoid stressing terminals and element sheath
• Inspect wiring and connectors; replace any heat-damaged spade terminals before reassembly

This genuine oven bake element heats the oven cavity for baking and roasting, restoring proper cooking temperatures and consistent results. Replaces a damaged or non-heating bake element to bring your oven back to service. What it does:

• Heats the oven cavity so food reaches and holds set temperatures
• Restores even baking and roasting when the oven fails to heat
• Replaces elements that show visible damage, burn-through, or no glow
• Works with electric ovens that use a separate bake heating element

• Disconnect power to the appliance at the breaker before starting work
• Handle the element carefully to avoid bending or damaging terminals
• Remove oven racks and access the element from inside the oven
• Verify proper fit and secure mounting; tighten terminal fasteners firmly and restore power to test