Frigidaire Heating Element

This heater assembly restores heat production in electric dryers so clothes dry efficiently. It replaces a failed heating element and helps return the appliance to normal drying performance. What it does:

• Heats air passing through the dryer drum so laundry dries during operation
• Replaces a burned-out or open heating element that causes no heat or weak heat
• Addresses long dry times and extended cycles when the element isn't functioning
• Works with the dryer's blower and thermostatic controls to maintain proper air temperature

• Disconnect power at the breaker before starting any repair; this part carries live voltage during operation
• Handle the heating element carefully to avoid bending or damaging the coil
• Inspect fuses, thermostats, wiring, and connectors while replacing the heater to ensure full repair
• Follow the appliance manufacturer's service instructions for disassembly and reassembly

The Element is an OEM component specifically designed for Frigidaire brand electric ranges. Located beneath the cooktop surface, these resistive elements generate heat for cooking.

Prolonged use causes elements to warp, crack, or lose continuity over time due to normal heating/cooling cycles. Element failure limits cooktop functionality.

Causes of a faulty element relate to typical wear expected of high-temperature filament windings. Accidental damage during cleaning can also impact integrity.

Symptoms of a bad element involve:

• One or more cooktop zones not heating properly or at all  
• Burned residue indicating heating dysfunction
• Visible cracks or separations in the resistive coils

Replacing with this OEM Frigidaire assembly restores reliable and consistent zoned heating. Compatibility extends to some Kenmore, Gibson, and Electrolux ranges.

This bake element heats the oven cavity so your range can reach and maintain baking temperatures for cooking and roasting. Replaces a worn or damaged oven element to restore consistent oven heating. What it does:

• Heats the oven interior during bake cycles to cook food evenly
• Restores expected oven temperature when a faulty element prevents heating
• Helps eliminate uneven baking or no-heat symptoms caused by a broken element
• Visible signs to watch for: blistering, breaks, or burn marks on the element

• One bake (oven) heating element

• Disconnect power to the appliance at the breaker or unplug before servicing
• Handle the element carefully to avoid bending or damaging terminals
• Verify correct part fit and terminal type for your model before installation

This is a replacement lower oven bake element that restores the heating surface used for baking and roasting. It installs in the oven cavity to produce the consistent radiant heat needed for proper cooking results. What it does:

• Heats the oven floor area to provide the primary baking and roasting heat.
• Helps maintain oven temperature so food cooks evenly.
• Commonly replaced when the oven does not heat or reaches lower-than-set temperatures.
• Replace if the element is visibly broken, burnt, or shows exposed wires.

• Disconnect power to the appliance at the breaker or unplug before starting.
• Handle the element carefully to avoid bending or damaging the terminals or insulation.
• Secure mounting screws as required.
• After installation, restore power and test oven heat; if oven still fails to heat, further electrical diagnosis may be needed.

This oven bake element replaces the bottom heating element that provides consistent heat for baking and roasting. It restores proper oven temperature so food cooks evenly and helps resolve heating issues. What it does

• Heats the oven cavity during bake cycles to maintain set temperatures
• Restores even baking and roasting when the oven underheats or cooks unevenly
• Can resolve symptoms such as no heat during bake, long preheat times, or inconsistent oven temperatures
• Connects to existing terminal studs and mounts at the rear of the oven cavity

• Disconnect power at the circuit breaker before starting any repair
• Allow the oven to fully cool and remove racks before accessing the element
• Replace using appropriate tools; ensure terminals are tight and insulated to prevent shorting

This heater assembly provides the heat source for the appliance, restoring normal drying and heating performance so clothes and items reach the expected temperature. Fits as a direct-replacement heating element assembly. What it does

• Generates heat needed for drying or baking cycles so loads dry thoroughly and on schedule
• Restores normal operating temperature when a failed heater prevents heating
• Helps eliminate long dry times or loads that tumble without warming
• Works with existing thermostats and safety switches to maintain correct temperature

• One heater (heating element assembly)

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Handle the element carefully to avoid bending the coil or damaging insulation
• Verify related safety components (thermal fuses, thermostats, high-limit fuses) if the new heater does not restore operation