Frigidaire Refrigerator Parts

This handle trim replaces a damaged or missing trim piece on the appliance's door handle. It restores a clean, finished look by covering mounting hardware and helps keep the handle properly aligned for everyday use.

• Finishes the end of the door handle and hides visible screws
• Helps stabilize the handle and maintain proper alignment
• Restores appearance when the original trim is cracked, loose, or missing
• Common signs: broken or missing cap, exposed screws, wobbly handle

• Disconnect power before servicing
• Open the door to access the handle; remove the old trim by releasing its clips or fasteners
• Align and snap the new trim into place; transfer any hardware if required
• Do not overtighten fasteners to avoid damaging plastic parts

The Cold Control is an OEM part for Frigidaire refrigerators. This component regulates the temperature inside the refrigerator by controlling the operation of the compressor and the flow of refrigerant. It ensures that the interior remains at the desired temperature to keep food fresh. This temperature control thermostat features a 16" capillary tube. 

Over time, the cold control can become faulty due to regular wear and tear, electrical issues, or exposure to moisture. A malfunctioning cold control can result in temperature fluctuations and ineffective cooling.

Symptoms of a bad cold control include:

• The refrigerator not maintaining the correct temperature
• The compressor running continuously or not at all
• Frost buildup in the freezer compartment
• The refrigerator being too warm or too cold

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This replacement guide aligns and supports a moving component so it travels on its intended path without binding. Replacing a worn or broken guide restores smooth operation and helps prevent scraping, jamming, or premature wear of connected parts.

• Keeps the associated rack, drawer, or panel centered and properly aligned during movement
• Provides a track/stop for the mating part to follow
• Reduces friction and noise for smoother sliding
• Typical failure signs: sticking, uneven travel, scraping noises, or visible cracks/broken tabs

• Disconnect power; also shut off water or gas
• Remove the associated assembly to access the guide and note its orientation
• Reuse original screws/clips and tighten securely without overtightening
• Test movement after installation; replace worn mating rails or rollers if needed

This door stop limits the opening angle of the refrigerator/freezer door to prevent overextension that can stress hinges or strike nearby cabinets. Replacing a worn or missing stop restores controlled door travel and helps prevent impact damage.

• Controls and limits the door's opening range
• Helps protect hinges, gaskets, and adjacent cabinets from overextension
• Restores smooth, consistent door operation
• Common signs: door swings past normal position, door hits wall/cabinet, visible broken or missing stop

• Unplug the appliance and lighten the door if needed for easier handling
• Support the door; remove hinge fasteners or pin as needed to access the stop
• Match the orientation of the original stop; retain any shims/spacers in the same order
• Reassemble and verify door alignment and gasket seal

The Door Stop is an OEM part for Frigidaire refrigerators. This small part helps protect the appliance's door from damage and prevents it from impacting walls or adjacent cabinetry, ensuring the longevity and integrity of your refrigerator's exterior. 

Causes of a bad Door Stop can range from physical damage due to forceful door opening, to normal wear and tear from repeated use. In some cases, the mounting area for the door stop may become worn or damaged, affecting its ability to hold the door stop securely.

Symptoms of a bad Door Stop include:

• The refrigerator door swings open wider than usual
• Noticeable wear, damage, or breakage on the door stop
• Difficulty in opening or closing the door smoothly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Kit includes ice and water actuator arms.

The Deli Drawer Cover Frame is an OEM part for Frigidaire refrigerators. It serves as the frame that holds and supports the deli drawer cover, ensuring a secure fit and smooth operation. The cover frame is designed to maintain the proper positioning of the deli drawer cover, allowing for easy access to stored items while preserving the overall organization and appearance of the refrigerator interior.

Symptoms of a bad Deli Drawer Cover Frame include:
• Difficulty opening or closing the deli drawer
• Loose or misaligned deli drawer cover
• Cracks, breaks, or visible damage to the cover frame
• Interference with other refrigerator components due to improper fitment

Causes of a damaged or malfunctioning cover frame can include accidental impact, excessive force applied during use, or general wear and tear over time. 

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This ice dispenser lever is the actuator you press with your glass to release ice from the freezer door. A worn or broken lever can keep the door dispenser from dispensing ice or make it hard to activate.

• Transfers your push at the dispenser pad to the ice dispenser switch
• Helps restore normal ice dispensing from the door chute
• Common symptoms: lever broken, loose, or stuck; no ice dispensed when pressed
• May cause intermittent dispensing if the actuator is worn or misaligned

• Unplug refrigerator before service; wear cut-resistant gloves
• Remove dispenser trim and control panel as needed to access the lever
• Note spring and pivot orientation; transfer any reusable hardware
• Test dispenser operation before reinstalling trim

This starter is the compressor start relay that briefly powers the start winding to get the compressor turning. Replacing a weak or failed starter can restore reliable compressor startup and consistent cooling performance.

• Engages the compressor's start winding at power-up, then disengages as the motor reaches speed
• Helps prevent repeated clicking, stalling, and overheating at the compressor
• Common symptoms include no cooling while fans run, compressor hums or clicks but won't start, or short-cycles on the overload
• Physical signs may include heat damage or a burnt odor on the original start device

• Disconnect power and allow the compressor to cool before service
• Discharge any capacitors per manufacturer instructions
• Note wire positions and terminal orientation; transfer leads one at a time
• Push the relay fully onto the compressor pins; ensure a secure fit without bending terminals

The Dispenser Module is an OEM part for Frigidaire refrigerators. It is an electronic component that controls the dispensing functions within the appliance's door or panel. This includes releasing filtered water, ice, and crushed ice on demand.

Causes of a bad dispenser module can include component malfunctions, circuit failures, or software glitches interrupting the dispensing process. 

Symptoms of an issue include:

• The dispenser not releasing any water, ice or crushed ice when tapped  
• Dispensing inconsistent amounts or none at all between uses
• Error codes shown related to the dispenser functions
• Operational noises from the dispenser that shouldn't occur

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Dispenser Module Cover is an OEM part for Frigidaire Refrigerator. It is the decorative plastic shroud that fits externally over the ice and water dispenser components.

Causes can be normal wear from frequent use of the dispenser, impacts from children or pets pressing on the area, or damage from attempted cleaning with improper chemicals over time.

Symptoms of a bad dispenser module cover include:

• Cracked, faded or stained external appearance
• Exposed wires and components vulnerable to liquid intrusion
• Cover not properly sitting flush or securely clipping into place

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models. 

This is the vertical flipper mullion assembly that mounts to one fresh-food door and pivots closed to seal the center gap when both refrigerator doors are shut, helping maintain proper temperature and energy efficiency.

• Creates the center seal between French-door refrigerator doors
• Helps prevent warm air infiltration and moisture/condensation in the fresh-food section
• Common failure signs include a loose or broken hinge, mullion not staying aligned, condensation at the door center, or doors not sealing properly
• May also be noted if doors pop open or temperature fluctuates in the refrigerator compartment

• Unplug the refrigerator before servicing
• Remove door bins to access mounting screws/clips
• Transfer any original covers or hardware if not part of the new assembly
• Verify proper hinge engagement so the mullion flips and seals smoothly before restoring power

This slide set replaces the side guides that support a sliding rack or drawer inside your appliance. Fresh slides restore smooth in-out movement, keep alignment true, and help prevent binding or derailment.

• Supports and guides a rack or drawer for smooth travel
• Helps maintain alignment and reduces friction during use
• Replaces cracked, warped, or worn slides that cause sticking or grinding
• Can help resolve binding, uneven movement, or a rack/drawer that pops off the track

• Disconnect power; shut off water or gas if applicable
• Remove the rack/drawer and retain any end stops, clips, or screws
• Note right/left orientation; transfer reusable hardware to the new slides
• Test full travel and smooth operation before returning to service

This condensate drain pan sits at the base of the refrigerator to collect defrost water and allow it to evaporate over the warm compressor, helping prevent floor puddles, moisture damage, and musty odors around the unit.

• Collects and holds defrost condensate from the drain tube (also called a drain pan or drip tray)
• Stages water to evaporate safely using compressor/condenser heat
• Replace if the pan is cracked, warped, missing, or leaking
• Common symptoms: water under/behind the refrigerator, damp flooring, or persistent musty odors near the bottom rear

• Unplug the refrigerator and pull it away from the wall; shut off water supply if connected
• Remove the rear lower access panel to reach the pan near the compressor
• Lift out the old pan; clear any debris from the drain outlet; transfer original mounting hardware if needed
• Seat the new pan level under the drain tube; ensure it's secure and reinstall the access panel

This refrigerator door stop limits how far the door swings open. Replacing a worn or broken stop restores the correct opening range, protecting the hinge and nearby cabinets while keeping door movement smooth and controlled.

• Mounts at the hinge to limit door swing and prevent overextension
• Protects the door, hinge, and adjacent cabinetry from impact damage
• Helps maintain proper door alignment and smooth operation
• Typical symptoms: door opens too far, bangs into surroundings, or the stop is visibly cracked/missing

• Disconnect power and clear items from the door before starting
• Support the door; remove hinge cover/fasteners and the damaged stop
• Install the new stop in the same orientation; tighten screws securely
• Reassemble and test the door swing to ensure it stops smoothly

This freezer basket hanger is the side rail that supports and guides your freezer's sliding wire basket. Replace a cracked or worn hanger to restore smooth movement, prevent sagging, and keep your basket seated securely.

• Supports the side of the freezer basket and carries its load
• Provides a track so the basket slides in and out smoothly
• Helps keep the basket aligned and level to prevent tilting or popping loose
• Common symptoms of failure: basket hard to slide, sagging/tilting, broken or cracked hanger tabs

• Disconnect power and remove food and the basket before starting
• Release/remove the old hanger (tabs/screws), noting its orientation; transfer any reusable hardware
• Seat and secure the new hanger, then reinstall the basket and verify smooth operation