General Electric Refrigerator Control Board

This authentic OEM part is a control board assembly for refrigerators. The control board assembly is the main circuit board that controls the refrigerator's essential functions, such as adjusting and maintaining temperature. If the refrigerator is no longer cooling and failing to maintain its desired temperature, the control board might need to be replaced. To replace the control board assembly, start by unplugging the refrigerator. After that, proceed to open the freezer door and unscrew the side panel to gain access to the old control board. Once accessed, remove the wire harness and any individual wires attached to the control board assembly. Unfasten the mounting screws holding the assembly in place, and pull the control board out. Set it to the side, and proceed to install the new board. Reattach the wires in their correct terminals, and reinstall the side panel. This genuine replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand refrigerators.

This refrigerator main control board manages the compressor, fans, and defrost system. Replacing a failed board can restore stable temperatures and reliable cooling performance when symptoms point to an electronic control failure. What it does:

• Regulates compressor and fan operation to maintain set temperatures
• Controls and times the automatic defrost cycle for the evaporator
• Interprets sensor inputs and distributes power to key components
• Failure symptoms include no cooling, warm temperatures, or erratic cycling
• Can present as heavy frost buildup, fans/compressor not engaging, or repeated relay clicking

• Includes: 1 main control board

• Disconnect power to the appliance before servicing
• Use ESD precautions; handle the board by its edges to avoid static damage
• Photograph/label connectors and move them over one at a time to the new board
• Ensure all plugs are fully seated and wiring is clear of sharp edges before restoring power

This electronic board powers and controls the light at the refrigerator's water/ice dispenser. Replacing it restores reliable illumination and proper on/off operation so you can clearly see the dispenser area during everyday use.

• Supplies regulated power to the dispenser light circuit for consistent brightness
• Responds to dispenser/control inputs to turn the light on and off
• A failing board can cause flickering or dim lighting
• Common symptoms include no dispenser light, intermittent light, or a light that stays on

• Disconnect power to the refrigerator before servicing
• Access the board behind the dispenser panel/escutcheon; remove trim carefully to avoid damage
• Handle the board by the edges and avoid static discharge; ensure connectors are fully seated

This power supply PCB provides the low-voltage power and control interface needed for the appliance's electronic systems, restoring proper power distribution and control signaling for displays and components. What it does:

• Converts incoming mains to the low-voltage supply used by control circuits and displays
• Delivers stable power to electronic modules so buttons, LEDs and sensors operate correctly
• Can resolve symptoms such as no display, blank/black control panel, or intermittent loss of power to controls
• Helps prevent erratic behavior caused by voltage irregularities or failed onboard regulation

• One power supply PCB

• Disconnect the appliance from power before beginning work to avoid shock or damage
• Handle the board by the edges and avoid contact with components to reduce ESD risk
• Verify the part number on the replacement board matches the original before installation
• Reinstall screws, connectors, or grounding per the appliance's service instructions

This refrigerator main control board is the central electronic module that coordinates cooling, fan operation, and defrost cycles. Replacing a failed board helps restore stable temperatures and reliable overall performance. What it does:

• Controls compressor operation and cooling cycles
• Drives evaporator and condenser fan motors
• Manages automatic defrost heater timing
• Interprets temperature sensor inputs to maintain setpoints
• Resolve: refrigerator/freezer not cooling, fans or compressor not running, frost buildup, or clicking/chattering from the control area

• Disconnect power before servicing; use proper ESD precautions and handle the board by its edges
• Photograph wiring and label connectors to ensure accurate transfer to the new board
• Transfer any jumpers or mounting hardware from the original board as required
• After installation, restore power and allow time for temperatures to stabilize

This encoder board assembly interprets user input from the range/oven control console and sends the correct signals to the appliance control system, restoring reliable button/knob response and control selection behavior. What it does:

• Converts knob/button movements into electronic signals the main control can read
• Helps ensure accurate selection of temperature, modes and timers
• Common symptom: controls are unresponsive or selections don't register
• Common symptom: erratic or intermittent control behavior when using the console

• Disconnect power at the breaker before starting any work
• Handle the board carefully and avoid static discharge; ground yourself or use an anti-static strap
• Keep track of screws and mounting hardware; label harnesses or take photos before disconnecting
• Reconnect harnesses fully and test function before reassembling the console

This electronic main control board coordinates your refrigerator's cooling system and user interface. Replacing a failed board can restore stable temperatures, proper defrosting, and responsive controls across the refrigerator and freezer compartments. What it does:

• Regulates compressor and fan operation using sensor feedback to maintain set temperatures
• Controls automatic defrost cycles to prevent frost buildup
• Interfaces with the human-machine interface (HMI) for button/display functions
• Common failure symptoms: fridge/freezer too warm, compressor or fans not running, unresponsive or erratic controls, or repeated relay clicking

• 1 main electronic control board assembly

• Disconnect power before servicing; use ESD protection when handling electronics
• Photograph wiring and move connectors to the new board one at a time; transfer any jumpers or mounting parts from the original
• Ensure all connectors are fully seated and covers reinstalled before restoring power
• After installation, set temperatures and allow up to 24 hours for cooling to stabilize

This is a control board for refrigerator units. This part controls all of the functions of the refrigerator. These functions include cooling, defrost times, alarms, lights, and more.If the buttons do not allow the user to change any of the controls or functions, it is likely that this part will need to be replaced. Some users report the refrigerator being stuck in a certain setting for an extended period of time. This is a high-quality replacement part. Be sure to disconnect the refrigerator from its power source prior to attempting to repair or replace this part. Wear gloves during the process for safety.This specific control board is compatible with refrigerators that are manufactured by the GE brand. It is sold individually and comes directly from the manufacturer.

This temperature control board assembly manages refrigerator temperature settings and signals to the cooling system for reliable, consistent operation. Replaces a failed control board to restore temperature regulation and user interface response. What it does:

• Regulates temperature setpoints and sends signals to the compressor, fans and defrost system
• Restores responsive front-panel controls and temperature display behavior
• Works as the central electronic controller coordinating cooling cycles

• Disconnect power before starting; risk of electric shock if not de-energized
• Handle the board by the edges and avoid static discharge (use ESD protection if available)
• Verify connector fit and orientation before fastening; do not force connectors

The Main Control Board is an OEM part for GE refrigerators. It serves as the central hub for managing and coordinating the various functions of the refrigerator, including temperature regulation, defrost cycles, and the operation of fans and compressors.

Over time, the main control board can fail due to electrical surges, wear and tear, or manufacturing defects. A malfunctioning control board can disrupt the refrigerator’s ability to maintain proper temperature and operate efficiently.

Symptoms of a bad main control board include:

• The refrigerator not cooling properly
• Erratic temperature fluctuations
• The refrigerator not running or turning off unexpectedly
• Unresponsive controls or display panel
• Unusual noises or clicks from the control board area

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This main control board assembly manages a refrigerator's electronic controls and user interface, restoring normal temperature regulation and cycle sequencing when the original control board fails. What it does

• Controls compressor, fans and timed defrost cycles to help maintain proper cooling
• Interprets user inputs and runs the control panel/display functions
• Responds to sensors and sends signals that regulate temperature and modes
• Common symptom: display or controls are unresponsive, fridge cycles erratically, or unit won't maintain set temperature

• Disconnect power at the breaker before removing panels or wiring to avoid shock
• Take a photo of wiring before disconnecting; replace only with the exact part number
• Handle board by edges and avoid static discharge; use proper ESD precautions

This transformer supplies low-voltage power used by freezer control components so the freezer's controls and related systems operate correctly. Replacing a faulty transformer can restore power to control circuits and return normal function. What it does

• Converts incoming line power to the low-voltage supply used by freezer control circuits.
• Restores power to control boards and related components when the transformer has failed.
• Can resolve symptoms such as unresponsive controls, dead lights or accessories in the freezer, and intermittent operation of freezer features.
• Works as a direct-replacement component when the original transformer is damaged or nonfunctional.

• One replacement transformer.

• Disconnect power to the appliance before removing panels or wiring; lock out power at the breaker.
• Access typically requires removing interior panels or the control housing—keep track of screws and fasteners.
• Match wiring connectors and terminal positions exactly; do not alter wiring or splice.

This electronic temperature control board regulates refrigerator cooling by reading sensors and commanding fans, compressor and defrost cycles to maintain set temperatures. Replaces a failed control board to restore proper temperature management. What it does:

• Receives temperature sensor signals and sends control commands to refrigeration components
• Helps stop irregular cooling, continuous run, or erratic temperature changes when the board has failed
• Works with defrost and fan systems to coordinate normal cooling and defrost cycles
• Restores electronic control when original board is unresponsive or damaged

• Disconnect power to the appliance before starting any repair
• Handle the board by its edges and avoid static discharge; use proper ESD precautions if available

This temperature control board assembly manages and regulates refrigerator temperature settings so your appliance maintains consistent cooling. It replaces a faulty control board to restore temperature control and proper cooling operation. What it does:

• Reads temperature sensors and sends control signals to compressor, fans, and defrost systems
• Regulates cooling cycles to help maintain set temperatures
• Can stop or erratically change cooling when failing or damaged
• Common symptoms: inconsistent temperatures, refrigerator running too long or not cooling, or control-related error codes

• Disconnect power to the appliance before starting any work
• Handle the board carefully; avoid electrostatic discharge and damaged connectors
• Verify connector locations and mounting match the original before final installation

This main control PBA is the refrigerator's electronic control board that manages user inputs, sensors and compressor/cycle functions to restore normal operation and control. It replaces a failed or unresponsive main circuit board. What it does:

• Interprets front-panel commands and runs the fridge's control logic
• Sends signals to compressors, fans and defrost components to regulate cooling
• Can resolve symptoms like unresponsive controls, no display updates, or erratic cycling
• Fix faults where the appliance won't start or shows control/communication errors

• Disconnect power before servicing to avoid shock or damage
• Handle the board by edges and avoid static discharge; use an ESD strap if available
• Photograph wiring and connectors before removal for correct reassembly
• Reinstall all mounting hardware and proper operation after power-up