Husqvarna Parts

Secures the mower blade to the motor shaft. Replace if adapter is worn, stripped, cracked, or no longer holds the blade firmly in place during use.

Replace a riding mower clutch when blades won't engage or disengage properly. This clutch transfers engine power to the mower deck for cutting control.

Steering shaft connects the steering wheel to the gearbox on riding mowers and lawn tractors. Replace if bent, cracked, or worn for proper steering control.

Engine won't start when you pull the cord? Replace the starter assembly. Includes housing, spring, and pulley. Moderate difficulty, 30-45 minutes.

This part is a clutch that is used on lawn tractors and riding lawnmowers. A clutch transfers the power from the unit's engine to the drivetrain and is responsible for engaging the blade.A new clutch may be needed if the lawn tractor or riding lawn mower will start but then stalls. If the clutch is sticky or if it operates hard, it may be time to replace the clutch. If the engine is revving higher than usual or if there are strange noises coming from the clutch, it is likely that the clutch could be going bad. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment.This clutch is a genuine Husqvarna part. It is sold individually. This particular clutch is compatible with lawn tractors and riding lawnmowers that are manufactured by Husqvarna and Poulan.

Recoil spring for chainsaw starter mechanism. Applies tension to pulley for rope retraction. Replace if worn, rusted, broken, or damaged to restore operation.

This kit includes replacement diaphragms and gaskets for the carburetor on a gas-powered chainsaw or other small engine outdoor equipment. These components create proper seals within the carburetor to regulate fuel flow and air-fuel mixture. Replace this kit if the engine is hard to start, runs rough, stalls frequently, or leaks fuel from the carburetor area.

Protects wheel hub and lug nuts from dirt and grime on riding mowers and tractors. Simple snap-on installation takes minutes with basic tools.

This replacement deflector shield is a genuine OEM part intended for use on lawn mowers and tractors. It attaches to the side of the mower and directs grass clippings away from the blade as it mows. This serves to keep grass from bunching up in the blade, which could cause it to stall out. The direction of the deflector shield also blows grass clippings behind the mower to keep any potentially hazardous debris from flying up at the mower. Deflector shields can become dried out and brittle over time and can snap off if the mower drives too close to a wall, tree, or other hard object. Deflector shields usually only need replacing if they break. This would cause grass clippings and debris to fly in all directions, which could be dangerous for the user. Replacing the deflector shield is an easy repair and only requires a socket wrench set. This part is compatible with a wide variety of Husqvarna and Craftsman lawn mowers and tractors and is sourced from the original manufacturer. This product ships individually.

Ground drive v-belt transmits power from engine to wheels on riding mowers. Replace if slipping, worn, or cracked. Verify fit with your model number.

This is a genuine OEM replacement drive V-belt for a riding lawn mower. The drive V-belt attaches to the drive pulley and transfers rotational motion from the transmission to the mower blade. This causes the blade to then spin and cut grass. By using a belt to transfer motion, the engine does not have to work as hard to spin multiple parts, meaning that it runs more efficiently. Drive V-belts are made of a rubber composite material that will begin to fray and stretch over time. Due to continuous motion, these belts absorb a lot of wear and tear, and if left for too long, they can eventually snap and leave the mower blade non-functional. Therefore, it is wise to check the condition of a V-belt during regular maintenance. As soon as it appears to be wearing away, replace it with a new part using a nut driver and screwdriver. When detaching the lower deck, be sure not to lose the bolt clips, as they are required for reassembly. As a high-quality replacement part, this drive V-belt is directly sourced from its original manufacturer. It is compatible with riding lawn mowers made by Husqvarna, Poulan, Craftsman, and Jonsered. This part ships individually.

Mandrel spacer washer for riding mowers and lawn tractors. Installs between drive pulleys to maintain proper alignment and spacing. Replace if worn or missing.

Hardened washer for lawn tractors and riding mowers. Installs with bolts to redistribute pressure and prevent loosening. Replace if worn or missing.

Secures the mower blade to the spindle on riding mowers and tractors. Replace if bolt is stripped, washer is damaged, or hardware is missing.

Idler pulley for riding mowers and tractors. Maintains proper belt tension for drive system. Replace if pulley is cracked, worn, or spinning rough.