Jenn-Air Range Heating Element

1st. replaced thermostat probe inside wall oven - no change. Then removed range heating element and measured it with ohm meter for continuity and found it to be OPEN. Ordered replacement range heating element; measured it before install and found it to be a few ohms - installed in less than 5 minutes and tested. ALL WORKS GREAT. Both items purchased with shipping were just over $100. (I chose to keep the thermostat probe instead of returning it being the oven is just over 10 years old). Read more

I replaced the bake element in the bottom of the unit. Read more

It only takes a screwdriver for this repair. Remove the two screws holding the old element, pull it out of the housing, making sure the wires attached to the element do not fall back into the housing when you unclip them. Once you reattach the wires, simply replace the two screws and the job is done. I could not reuse the old screws though since the old ones did not hold the tight (unit is 20 years old and they were simply stripped). I simply increased the thickness of the screws and the new... Read more

Installed the new pans and replaced the coils. My Jennaire looks like new. Only took minutes and made such a difference. Read more

Ordered part and installed it. Broiler works as advertised. Read more

Your on line video pointed out the problem, how to test, and how to replace the element. I ordered the part it came the next day. Wife is very happy. Read more

Ordered new one from you, unscrewed and unplugged the old one, plugged in the new one Read more

• Little to no heat when baking
• Oven not heating evenly

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

Range has no model ID plate anywhere. Flip off electric at circuit breaker box. Opened top of range and noted details of the faulty burner, including confirm that outer coil was fried. The maker info on back of element was useless in finding replacement: more useful was general shape, and the numbers around edge on back. Close up range, since low heat element still working. Turns out all Maytag double oven Gemini ranges use the same hi-low element, but double check appearance just in... Read more

• Element will not heat

I ordered 2 bake elements and bulbs and was able to easily fix 1 of the ovens. The serviceman who repaired the left oven did not repair it correctly so, one of the wires was not accessible so, I could only fix one oven. After shutting off the power, I EASILY fixed the right oven - with a LOT of care and a little elbow grease - in disconnecting the broken element, by doing exactly as it said to in the video, making certain not to allow the wires to slip back into the hole that it was pulled... Read more

• Element will not heat

I diagnosed the problem, found Appliance Parts Pros and watched their video. It was as easy as the video they made said it would be. Overall an amazing experience. I was quoted $250 to have the repairman come do the same thing. My cost was $40. Read more

• Element will not heat

I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help. Read more

• Element will not heat
• Little to no heat when baking
• Oven not heating evenly

Removed 2 sheet metal screw pulled element out about 2 inches. Removed two Spade connections. Removed the element from the oven. Inserted the new element into the over, connected the two spade connector. Reinstalled the two sheet metal screws. Set the oven to bake for testing and tested until the element turned red. Total time less than 5 minutes. Read more

• Little to no heat when broiling
• Element will not heat

Turned off breaker to oven, took pictures of existing broil, supporting bracket and shield attached to oven, removed screws holding element, support piece and shield, removed bracket and shield, pulled out the element, took another close-up picture of the wires connected to element, removed wires, connected new element, turned breaker on to see if connection is correct, turned it off, installed element, shield and support bracket (in this order). Turned breaker on. Hardest part was loosening... Read more

Watched videos online and with that knowledge it was a very simple process. Read more