Kenmore / Sears Dispenser Parts

The washer would work fine except it wouldn't spin unless you opened the lid and waited a split second for it to stop. You would hear a bang, then when you closed the lid, it would spin. Since it made that bang noise, I thought the transmission was going bad, so I replaced that. Nope, still the same. So, after a little more research, I found out that the motor has to come to a complete stop for the transmission to go into spin mode. After pulling out the timer and inspecting it, I noticed... Read more

Purchased a fabric softener dispenser from appliance parts pros removed cap from agitator and replace with the new fabric softener dispenser and problem solved. Read more

I purchased part #85753076A, Whirlpool Fabric Softener Dispenser. Popped off the top from the agitator and popped on the fabric softener dispenser. It took me less than a minute and it works perfectly! No more missing the rinse cycle!!! Read more

Got online and searched for part by washer model number. Found AppliancePartsPro.com. They listed diagram of part. I ordered it online and received it next day with no extra charge for fast delivery. My husband attached cosmetic drawer cover to detergent drawer part we ordered in a few minutes. It fits and is working! Speedy service was appreciated. Read more

Took cover completely off and tried putting back, could not match up left screw with available screw hole. Tried many different configurations and sequences to make this happen. watched a video on changing the front panel, the door in it had four screws, mine 2, no help there. Searched on the hyperextending issue, found an article about dogs and kids [had both here] climbing on the door and to check the springs and linkages. Linkages intact both sides, R [opposite] side spring very stretched.... Read more

So I ordered the face plate and other parts that went with it and fixed it myself. The repair man wanted around $600 to do it. I believe kt cost around $160 to fix it myself. Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

Replaced the actuator pad on the Whirlpool Gold Series, releasing the electronic menu pad to get to the water activator pad was the biggest hurdle. The release tabs are underneath the menu pad and you may feel as if you may break them when releasing them. They did not break but I did hold by breath. Read more

We ordered the dispenser cover kit. the problem was with the spring. followed your "how to" video and it was a quick and easy fix! Read more

I watched the video on your site and it showed step by step how to replace the spring. Excellent shipping time. Good customer service on chat forum. Read more

This was a pretty easy fix. Removed the screws around the perimeter of the inside cover of the door and pressed the outer door cover upward to release it from slots retaining it. There are four wires to remove (2 for the detergent door release and 2 for the rinse agent release). Removed the 6 screws retaining the dispenser assembly and inserted the new one. Reassembly is simply in reverse order. Problem solved for less than the cost of a service technician's call! Read more

Ordered new part, very easy to replace only took about 5 minutes to install new part and get everything going again. Part was a perfect fit and was shipped and received in only a few days. Thanks Read more

Replaced soap dispenser unit Read more

My appliance is a Kenmore, and even though the video mentioned lots of other brands, it showed the exact same problem I was having. My dispenser motor just spun and spun, never stopping at the various positions it was apparently supposed to. Then it would trip the F30 code. The part description again mentioned these other brands but did say in fine print it fits some Kenmore products. I could tell visually from the video the part was the same as on my washer so I felt confident the part... Read more

Replaced ice chute door by watching video. Read more

Took top off and did a line at a time Read more