Kenmore / Sears Dryer Fuse Or Sensor

You can do this! Although an Art Director by trade, I like working with my hands. I’m adept at working with tools and following instructions. In today’s disposable society, I prefer fixing things. That said, this has to be the easiest repair I’ve ever attempted with the largest cost-savings versus hiring a professional. My brand new dryer had been in use fewer than six months (average 6 loads per week) when suddenly the dryer would not heat. The drum would spin, there were no error codes, and... Read more

• Shuts off too soon
• Too hot
• Takes too long to dry
• Won't start

Recommendations have fun and a bucket to prevent losing parts. First watch the videos, practice disassemble and reassemble the dryer drum. Make certain you have a good screw driver and spatula from kitchen (could not find my putty knife). Secondly, clean and inspect everything, make sure the motor bearing and belt pulleys are in good condition with little or no play. Third after you have confidently disassembled, vacuum cleaned, inspected all the worn parts, grease the motor and pulley,... Read more

After reading the reviews of others, I ordered and replaced the heating element, thermostat, cut-off & the moisture sensor bars. It was a success! The element was definitely bad on one end, the wire was burnt in two pieces. Now it doesn't take 3 hours to dry a load! Well worth the money I spent. Easy to fix & do it yourself. I watched the video before buying the parts just to make sure that it was something I wanted to tackle. Very easy with the video. Great job Appliance Pro's! Read more

First ran the built-in diagnostic tests. Got error code indicating that the inlet thermistor was open. Removed lower access panel and did continuity checks on the inlet thermistor, thermal cutoff and heating element. Even doing these checks is very difficult on this model due to the location of these parts and the limited access through the so-called access panel. But was able to get an open reading on the heating element, so I knew that at least that part was faulty. Could not get a reliable... Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

I think I have a lemon of a dryer. I keep having to pay someone to replace my heating element about every year. So I already had the heating element, but I thought I would replace the thermostat and the limiter also. Yes, I am a 46 year old mom, and I replaced all three items. Thank goodness to youtube! Ha! I have ordered from you before and you always send promptly. Thanks! Read more

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

Purchased, Igniter Kit, Gas Valve Coil Kit, and as a precaution Thermal Fuse and Cutoff-Tml. Was pretty confident the problem was the gas valve coil, but figured that why not just replace the other items while I had the unit apart. Researching and utilizing this site certainly helped me out in figuring what the problem may be. Watched the instruction videos which were very detailed and helpful. The replacement and repair was not that difficult and the work was done rather quickly. Doing... Read more

• Too hot
• No heat or not enough heat
• Takes too long to dry

Replaced thermal stats Read more

After I cleaned out the typical 1.5 pounds of lint from the vent, ( I do it every 2 months), I went searching for a solution. I found 6 possible causes on this site and purchased everything except a new burner; I wasn't going to go that far. Let the fun begin. Since my vacuum was still nearby, I thought I was ready for anything. Wrong. After I watched all the videos again for reassurance, I went in with screwdriver in hand and laptop nearby. I removed the top and looked inside. Don't be fooled,... Read more

• Takes too long to dry
• Doesn't shut off

I researched the issue on You tube and found out it could be either the "belt broke switch" or the Moisture sensor. A friend who was an appliance mechanic advised "since you have to take it all apart anyways, its best to replace the belt, spring, and Idler wheel" I bought the 5 item for $52. I watched the video on the AppliancePartsPros for changing out the belt and I replace all items on the list. Took 1 1/2 hrs and was fixed on restart!! * Wear gloves, the sheet metal is very sharp edges!* Read more

• Too hot

I looked at online repair videos on how to fix a Maytag dryer. When I knew what parts I needed, I could not find any local supply stores for the part. It was late Friday afternoon when I ordered my parts on AppliancePartsPros.com It stated Standard delivery was two business days. So I expected my parts to arrive on Tuesday. To my great surprise, the parts arrived on SATURDAY. Totally shocked, but extremely pleased. Read more

Replaced control board. Did not need Control Thermistor in my case, but I'm keeping it as backup. Got the Drum Belt just in case it breaks on me since the dryer is aging. To replace control board: Disconnect power and pull dryer away from wall. Take 2 black screws on the back off to remove the top lid. Remove 2 screws on top that hold the control interface on. Remove 2 screws on the bottom backside of the control. Pull out control panel and pull off terminal connections and push to remove... Read more

• No heat or not enough heat

Changed out high limit thernasstat Read more

I tried to buy a new refigerator, but strangely none of the major stores had anything I wanted in stock. The earliest delivery date for a new unit was over a month away. At that I decided to try and keep this one running. I did online research into common refigerator problems. I found the cooling coils in the freezer were covered in a block of ice and frost. The refigerator was not going through a defrost cycle. With a hair dryer I thawed out the coils. The refigerator worked fine for... Read more

Installed new drive motor. We are an animal emergency hospital and need clean laundry 24/7. I received motor the next day and was fixed by 3 PM. Most of the time spent repairing is actually spent on cleaning out all the lint inside of machine. Read more