Need Help?
Call or text
Traps lint and debris during drying. Replace when mesh appears clogged, melted, or reduces airflow. Confirm fit with your model number before ordering.
Simple fix, just replaced the screen with the new one I ordered from you Read more
Replacement air duct assembly with mesh screen for dryers. Installs between drum and heater. Replace if screen is burnt, cracked, melted, or missing.
It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more
The Igniter Sensor is an OEM part for LG dryers. This sensor plays a critical role in the ignition process, ensuring that the gas ignites properly to produce the heat necessary for drying clothes efficiently. It helps monitor and regulate the ignition
Used video and took apart dru, this was extremely helpful. I bypassed the belt and door switch. Tested gas valves (gas disconnected) with multimeter. Found that the igniter worked the first gas valve, but the second gas valve would not open and the igniter would stay on. Found a flow chart online that shows the flame detect turns on causing the gas to turn on and shuts off the igniter. I replaced it and tested again. Igniter turns on, shuts off, then power to the second gas valve turns... Read more
The Water Inlet Valve is an OEM replacement part for Whirlpool dryers. Located where the water supply line connects, it controls the flow of water into the dryer drum for steam cycles. Precise control is needed to prevent temperature fluctuations or fl
Ordered new valve. Easy installation. Saved a service call charge (-; Read more
Dryer won't power on or has loose power cord connection? This terminal block screw kit secures electrical connections. Easy DIY fix in 15 minutes.
And after replacing the thermal fuse The dryer turned on. Read more
Freezer or fridge light not working? Door alarm going off? This door switch detects when doors open/close to control lights. Easy 15-minute fix.
Ordered the freezer door switch and the light. Replaced the freezer door switch and the light and everything is back to normal. Replaced both in less than 15 min with no problems. Read more
White outer door handle for dryers and washers. Snaps into place on the door panel. Replace if cracked, broken, or missing for easy door operation.
I looked at a video on YouTube and followed the instructions. Read more
This is an igniter and bracket assembly, and it is intended for use in dryers. This is a genuine replacement part made by Speed Queen. The igniter is connected to the dryer on the back of the appliance, and it is used to heat the drying tub. A new igniter
Had handyman fix machine Read more
The Door Hinge is an OEM part for LG dryers. This hinge supports the dryer door, allowing it to open and close smoothly and securely. It ensures that the door stays aligned and functions properly, providing reliable access to the dryer drum for loading
This part was the perfect fix for my broken door hinge on my LG front loading dryer. I watched a video on YouTube of a hinge replacement of a similar front loading Samsung dryer. I needed a little help from my son holding the door glass and plastic in place while re-attaching the door to the hinge, but it was an easy repair. Read more
Dryer door seal prevents air leaks and retains heat inside the drum. Replace when loose, torn, or causing heat loss. Includes adhesive. Verify fit.
Ordered new seal and the correct adhesive to use and followed directions for resealing of the door. Read more
Replace your dryer's control knob if it's broken, cracked, or missing. This knob installs on the control panel to select drying cycles and settings.
The knob broke off the plastic arm that came out of timer. Had to replace timer and knob. Very easy repair. Read more
Dryer won't start, stops mid-cycle, or runs backward? The drive motor powers drum rotation. Moderate difficulty repair requires disassembly. Video guide.
I could hear the dryer motor hum, but it would not run. There was nothing obstructing the motor from turning freely so I assumed I needed a new motor. I went ahead and ordered a new pulley switch to change out while I was in there just in case. The parts arrived faster than expected. I changed the switch first and then checked the old motor which surprisingly fired right up. Now I have to decide whether to return the new motor or keep it as a spare. Read more
Fix odd rattling noises or no airflow from vents with a new dryer blower wheel. Common issue: lint buildup or wheel separation. Moderate DIY repair.
It was a relatively easy fix - if you know how to take the dryer apart. If you don't, there are plenty of YouTube videos explaining how. Make sure you find your model. Since the wheel had separated from the nut, it wasn't quite as easy and holding the shaft and loosening the wheel. I had to remove (destroy) the wheel first. Then I was left with the nut on the shaft. The nut was seated on the shaft a lot tighter than I expected and took some force to get off. Once it was off, putting the new... Read more
Dryer not heating? A faulty heating element is often the cause. This part generates heat to dry clothes. DIY-friendly repair, takes 30-60 minutes.
Put in new part. It was done by maintenance personal and took just a few minutes. Read more
Dryer runs but won't heat or won't stop at cycle end? The timer controls heating element power and cycle completion. Moderate DIY repair, 30-45 minutes.
Used ohm meter on all thermostats and element.everything looked good.wasnt getting power to element unless you wiggled timer knob .ive used this website a bunch because it beats everyone else's prices Read more
Converting dryer from LP to natural gas? This gas orifice regulates gas flow to the burner for proper heating. DIY-friendly swap, takes 20 minutes.
Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more