Kenmore / Sears Gasket & Seal

Loosened the top half screws, pulled the old seal out, put new seal in, snugged top screws, repeated process for the bottom. Went well, no problems. Read more

Let the gaskets straighten out a bit overnight. Pulled out the old gasket, Cleaned and dried the area well though almost all the mold was in the old gasket. Pressed in the new gasket. Use a hairdryer to warm up and press the slightly deformed areas of the gasket into place. Quick and EASY. Read more

After troubleshooting the problem I checked online for similar issues and how they were resolved. I discovered the video on YouTube for replacing the wash tub boot. Although the video was for a Whirlpool washer it turned out to be spot on for my Kenmore Elite. The breakdown and removal of the torn boot was bolt for bolt perfect. I ordered the part direct from Appliancepartspros.com on a Sunday night and it arrived by Tuesday afternoon. I watched the same video over, replaced the boot then... Read more

Ordered the parts online and fixed it myself. Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

Easily found replacement part at AppliancePartsPro.com. It arrived surprisingly soon after order. Watched the "how to replace" video and followed guidance. Removal and replacement went very smoothly and better than hoped for. Door now seals tight. Read more

• Door sweating

New seal, old one pulled out easy and new one pushed into place. Read more

Myself Read more

Removed the top cover while the machine was operating, located the source of the leak. The top filler tube had worn a hole in a flex point. Found the right part on this site, replaced it with little effort. While in there I saw a similar hose and decided to replace it as its time was probably up too. So far so good, washing clothes and no leaks!! Great prices and best of all the right parts were delivered in a timely manner. Thanks for making this so easy. Only specialty tool used was hose... Read more

• Fridge too warm

Unfortunately, this model has the screws that you need to loosen before you can squeeze the rubber in but the gaskets fit perfectly. It took a lot more time than the video showed but that was because the video was of the pop in type. Be sure when pushing the rubber under the metal strip you make sure it actually goes in. I think the last people installed the gaskets incorrectly and that's why they broke and pulled out of place. Unscrew the bolts first, I used an electric drill. The old gasket... Read more

Replaced it with a new one from appliance which we received in one day Read more

An online search for LG washing machine parts came up with a repair video from Appliance Parts Pros. I watched the video. It was very well done, very detailed, and took you step by step through the entire process to replace the tub bearings and the spider, from start to finish. After watching the video, I realized this repair was well within my abilities. No specialized tools were needed. I ordered the parts from Appliance Parts Pros, and all items were in stock and delivered within a couple... Read more

Replaced clutch assembly, gearcase input shaft seal and motor coupler. When I disassembled the washer I realized the shaft seal on the top of the gearcase was leaking and not the input shaft seal. So had to order more parts before I could finish this job. Altogether I replaced agitator dogs, both seals on the gearcase, the clutch assembly and the motor coupler. Agitator dogs replacement is a very easy job, no tools required, takes less that 5 minutes and made a huge difference with how well... Read more

Removing was easy. Pull out the ends of the seal, the ends aren't locked in. Then, pull up on each retaining clip. Each clip is held in with spring tension. Reinstallation was easy too. Start on one end, Twist frayed end into cone-like shape and insert into one of the holes for the seal. Push in with a skewer/screwdriver. Insert first clip into the first hole. Go around in a linear fashion, inserting each clip into each hole. After the last clip is pushed in, twist the end of the frayed end... Read more