Kenmore / Sears Heating Element

• Element will not heat

I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help. Read more

• Little to no heat when baking

I just took them off and replaced them. Read more

Ordered new bake element on 01/03/2021 and received on 01/05/2021. Thanks for the expedited service. My husband removed the old bake element and replaced with the new bake element. Took less than 15 minutes to remove and replace. Read more

Replaced the heating element and we have heat to dry our cloths THANKS Read more

The instructions that came with the replacement smaller surface heating element provided no help about how to open the top of the range, so I checked the internet. I found several videos on replacement of surface elements in flat top ranges, but none for our particular range, so I Google-searched a simple question, “How to open the top of a 6898VVD Magic Chef range”. The AI Overview answer had several points, most of them not useful, except for the last one: “Hidden Clips: There might be... Read more

Watched videos online and with that knowledge it was a very simple process. Read more

With the help of Wendee and Karen, we finally figured out my model numbers and which parts where correct. I ordered the parts and all arrived the next day except for the Broiler element which arrived in 2 days. I installed the new Baking Element myself. Took longer to figure out which curcuit braker to turn off. In about 30 minutes I had a brand new Baking Element in my oven working perfectly. On the following day, I installed the Broiler Element. That took a bit longer as it sits in a metal... Read more

• Little to no heat when broiling
• Element will not heat

Turned off breaker to oven, took pictures of existing broil, supporting bracket and shield attached to oven, removed screws holding element, support piece and shield, removed bracket and shield, pulled out the element, took another close-up picture of the wires connected to element, removed wires, connected new element, turned breaker on to see if connection is correct, turned it off, installed element, shield and support bracket (in this order). Turned breaker on. Hardest part was loosening... Read more

• Element will not heat

Purchased a new Element surface and installed same... All Okay now... Read more

• Little to no heat when broiling

I wanted to get the upper oven baking element replaced; it hasn't been working for a few months. This double oven has had two other issues, there is a fan that comes on to cool the electronics panel, That fan has made excessive noise and it operates for 2-3 hours after the oven turns off. The other problem with the oven is the Self-Cleaning feature runs for about 15-30 minutes and then turns off with an error code. I've had a local appliance repair person in to address the error code and... Read more

Pulled out the old one, popped in the new one 20 minutes. Fixed. Read more

• Little to no heat when broiling

Come to find out after replacing the element, it is the control card Read more

Turned off power to oven. Removed the oven door. Unscrewed and removed the metal plate. Pulled element off wires and attached them to the new element. (This took needle nose pliers and many attempts. Needed dexterous fingers and good eyesight.) Put everything back. Read more

Little procrastination paid off. With only 50% capability I knew it is time to call the appliancepartspros. They shipped me parts within 3 days. It was practical to fix both at the time. All I needed was to disconnect power at range breaker box, grab a screwdriver to lift top open, a 16 inch or so piece of old 2×4 wood to keep the top top of stove lifted, so I could access heating elements from underneath. Then I took my black sharpie And marked location of mounting screws and... Read more

Ordered new heating coils for stove Read more

• Little to no heat when broiling

Cut off power ,inside I remove the two back screws, remove the two front screws with hangers. Pull element out, clip wires so they don't fall back in holes with clothes pins. worked good. But wire connection to the broiler was to large, had to replace connectors, wire fell in hole, had to pull wall oven out and remove back panel. I then mounted the new element to oven. Replaced connectors ,connected connectors, closed back panel, put oven in place ,connected power lines. Turned power on. Works... Read more