Kenmore / Sears Refrigerator Ice Maker & Related

Removed old seal and installed new seal. I laid down the new seal in the sun for about 20 minutes and it went in the grove extremely easy. Read more

I found that the Ice Maker in my GE side by side made ice but would not kick out the ice when it had formed, the heating element or the switch that controls it didn't work. I ordered a new ice maker switched it out took less than 3 minutes. The cord was very stiff and just long enough but I got it to connect and in 35-40 minutes I had fresh ICE!! Read more

Replaced the ice dispenser motor( very easy only 4 screws and a power plug. I also replaced the auger drive shaft and rubber grommet Read more

All the corners of the Ice Bucket were cracked and was causing the screw inside the bucket to jam. Read more

Replaced it completely in less than an hour. Part was exact OEM replacement and worked perfectly. Read more

Take off freezer door and tried to take off top shelf. Never got shelf off. Made it more difficult but got it replaced. Read more

Well, I took it out (it slides out) to get a good look at it,so i could ref pictures on your site..naturally I had serial/model of refrig,and thats mandatory to get the right part. It came in 2 days,,and being just the bucket, it took only a few minutes to transfer the auger assembly/cube/crusher.... into the new one, 6 screws total..Your site has excellent vids on DIY.......I HIGHLY reccomend. Whole process was'nt over 15 minutes, piece of cake....And NOW i can go back to my nightly 'scotch... Read more

Replaced icemaker and shutoff arm. Easy project. Read more

Replaced entire ice maker. A couple of important points. (1) The ice maker module does not include all parts. The door flap for example is not included. So save all plastic parts from the old unit including screws. The biggest installation problem was the power cable. There was little room on the side of the ice maker for the cable and connectors to fit. Make sure the connector that mates with the refrigerator cable is seated onto the plastic housing and does not stick out or dangle out.... Read more

• Ice maker dispenses too much ice
• Leaking
• Ice maker not making ice

Watched online video and worked along - it was easy and quick - I was amazed! Read more

Although the solenoid I purchased did not fix the problem, nor the "mother electronic board", or the motor, my experience with Appliance Parts Pros has been excellent. Extremely easy to look-up parts for my model refrigerator. Best part is their video instruction that gives you step-by-step hands-on how to remove and install. I would highly recommend these folks. If a lady such as myself can do repairs based on their instruction, anyone can. Thank you for providing such an informative... Read more

• Ice maker won't dispense ice

I first thought it was the auger in the ice container so I changed it and it was not the problem. I then talked to ApplianceParts customer service that it might be the yoke on the motor that turned the auger or even the motor itself even though it worked. I ordered the parts, the yoke was supposed to be able to be changed by itself but mind would not come off the motor shaft so I had to cut it off just to remove it from the unit so I had to change the motor anyway because of this. So I advise... Read more

My fridge was too cold - everything was freezing solid, even in the produce bins. The air from the diffuser vent was constantly running. After unplugging the fridge and plugging it back in, the diagnostic code on the control panel indicated that the air diffuser was not working. I purchased a new air diffuser, watched the very helpful video that showed how to install it, and replaced the part in about 10 minutes. The next day, I can tell that everything in my fridge has finally begun to thaw... Read more

Purchased the kit, followed instructions, within 30 minutes had the new ice maker installed. Works wonderfully. We were quoted over $350 to fix it from a repair agent, but it only cost $150 including shipping from you guys. Very happy. Read more

I replaced the 2 metal parts that were rusted out. Read more

Had to replace the auger. The auger on my ice maker was made of plastic and had broken pieces off it. The new one is made of metal and seems to work much better. Was a fairly simple repair. However pay close attention when disassembling, I recommend using your cell phone and snap a pic of the different stages as I became a little confused when putting it back together. Ordered the part and it was here the next day. I'm very happy to have my ice coming down the chute again. By the way, I'm a 70... Read more