Lg Auger, Helix, Crusher

The Icemaker Assembly is an OEM part for LG refrigerators. This assembly includes the necessary components to produce and harvest ice within the freezer compartment. It ensures a steady supply of ice cubes for your household.

Causes of a bad icemaker assembly can include wear and tear over time, issues with the water supply line, electrical malfunctions, or mechanical failures within the icemaker unit. These problems can lead to the icemaker not producing ice or producing ice irregularly.

Symptoms of a bad icemaker assembly include:

• No ice production
• Ice cubes being smaller or misshapen
• Ice cubes sticking together
• Unusual noises from the icemaker
• Water leaks around the icemaker area

This OEM LG part is also compatible with Sears/Kenmore models.

This AC motor powers the appliance's fan or blower to move air through the system. Replacing a worn motor restores proper airflow to support cooling/ventilation and protect internal components from overheating. What it does:

• Rotates the fan/blower to circulate air through the appliance
• Helps maintain proper temperatures and component cooling
• Common failure signs: fan won't start, starts then stalls, weak airflow, loud humming/grinding, overheating or safety shutoffs
• Often required when motor bearings seize or windings fail

• 1 AC motor

• Disconnect power and allow hot components to cool before servicing
• Note wire positions; transfer any brackets, grommets, or the fan blade from the original motor if reused
• Clear debris and restore power and verify smooth, quiet airflow

This ice bucket assembly stores and delivers ice to the dispenser. Replacing a damaged bucket restores smooth, reliable dispensing and helps prevent jams when the original container is cracked, worn, or no longer engaging the drive.

• Stores finished ice beneath the icemaker and positions it for dispensing
• Interfaces with the dispenser drive to move ice into the chute when activated
• Helps maintain proper alignment for consistent cube delivery
• Common symptoms: cracked or broken container/tabs, ice won't dispense or jams, grinding/skipping during dispense

• Disconnect power to the refrigerator before servicing
• Remove the old bucket; empty ice and note the drive coupler orientation
• Seat the new assembly fully so the drive engages; transfer any reusable covers from the original if needed
• Restore power and test ice dispensing

This ice maker lever is the mechanical arm that controls ice production by interacting with the ice maker's on/off and level-sensing mechanism. Replacing a broken or missing lever restores proper operation and helps prevent overfilling or no-ice conditions.

• Acts as the ice maker's shut-off arm to regulate ice production
• Lowers to allow ice making; raises to stop when the bin is full
• Common symptoms: ice maker won't stop making ice, no ice when arm is stuck up, broken/missing lever, lever won't stay in position
• Helps ensure consistent, reliable ice production control

• Disconnect power and shut off water before service
• Remove the ice bin to access the ice maker; gently release the lever from its pivots/linkage
• Note lever orientation; transfer and reuse any original springs, clips, or fasteners
• Reinstall components, restore power, and verify free up/down movement of the arm

This ice bucket assembly stores the ice made by your refrigerator and delivers it to the dispenser. Replacing a cracked or worn bin restores dependable storage and smooth dispensing, reducing jams and spills at the door.

• Collects and holds ice from the icemaker
• Guides and feeds ice toward the dispenser when activated
• Aligns with the drive mechanism for smooth dispensing
• Common symptoms: ice not dispensing or dispensing inconsistently, dispenser jams, visible cracks or broken tabs on the bin

• Disconnect power before servicing
• Remove the old bin; empty any remaining ice and press any release latch if present
• Seat the new bucket fully so the rear drive coupler engages; do not force
• Restore power and allow the icemaker to cycle fresh ice before testing dispense

This ice bucket holds and stores ice produced by the refrigerator's icemaker, keeping cubes contained and easy to access. It replaces a cracked, damaged or missing bucket so ice can be collected without spilling into the freezer. What it does:

• Collects and stores ice produced by the icemaker until you remove or dispense it
• Keeps ice contained to prevent loose cubes from scattering in the freezer
• Restores proper seating for the ice delivery area to reduce jams or blockages
• Useful when the original bucket is cracked, warped, or missing

• One ice bucket

• Unplug the refrigerator or switch the icemaker to OFF before replacing the bucket
• Remove all loose ice and the old bucket before installing the new one
• Slide the new bucket into place until it seats securely; do not force
• Rinse the new bucket with clean water before first use

This is the condenser fan motor for select LG-built refrigerators. It drives the outside rear fan that pulls air across the condenser coils and over the compressor to remove heat so the refrigerator can cool efficiently.

• Circulates air through the condenser section to dissipate heat
• Helps prevent overheating of the compressor
• Common failure symptoms: fridge not cooling well, compressor running hot, loud or grinding noise from rear bottom, fan not spinning
• May run intermittently or seize when failing

• Disconnect power before servicing; use cut-resistant gloves
• Access from the rear lower service panel near the compressor
• Note wire orientation and fan blade position before removal
• After replacement, ensure the fan spins freely and no wiring contacts the blade

The Ice Bucket Assembly is an OEM part for LG refrigerators. It is designed to collect and store ice produced by the icemaker, ensuring a convenient and organized storage solution within the freezer.

Causes of a bad ice bucket assembly can include damage from frequent handling, cracks or breaks due to impact, or issues with the internal components such as the auger or motor. Over time, these issues can impair the functionality of the ice bucket, leading to inefficient ice storage or dispensing problems.

Symptoms of a bad ice bucket assembly include:

• Cracks or visible damage to the bucket
• Ice not dispensing properly
• The bucket not fitting securely in place
• Excessive noise during ice dispensing

This OEM LG part is also compatible with Sears/Kenmore.

The Ice Maker Assembly is an OEM component specifically designed for LG refrigerators. It is responsible for automatically producing batches of ice cubes through an electrical freezing process.

Causes of a bad ice maker assembly can include failures in the electrical components, freezing properties deteriorating over time, or physical damage to the assembly housing. 

Symptoms of a bad ice maker assembly include:

• No ice production or very slow icemaking  
• Cubes that are improperly formed or jammed inside the unit
• Error codes displayed related to the icemaker
• Leaking or water issues around the assembly area

This LG part is also compatible with Sears/Kenmore models utilizing the same refrigerator chassis and components.

The Ice Maker Assembly is an OEM replacement part for LG refrigerators. As the main ice production component, it contains all the components needed to automatically mold, harvest, and store ice within the freezer compartment.

Causes of failure can be normal wear and tear of internal gears, wiring issues, or failure of the temperature control sensor. Mineral build-up may also affect performance over time.

Symptoms of a faulty ice maker assembly include:

• Inability to produce ice or fill the ice tray
• Erratic or intermittent ice production
• Broken or dysfunctional ice cube release mechanism
• Water pooling inside the freezer from the icemaker leaking

This OEM LG part is also compatible with some Sears/Kenmore models.

The Icemaker Assembly is an OEM part for LG refrigerators. It is responsible for producing and storing ice within the freezer compartment.

You should replace the icemaker assembly if it becomes faulty. Causes of a bad icemaker assembly can include wear and tear from regular use, mineral buildup from hard water, or failures in the mechanical or electronic components. These issues can lead to inconsistent ice production or complete failure to produce ice.

Symptoms of a bad icemaker assembly include:

• The icemaker not producing ice
• Leaking water around the icemaker
• Ice cubes that are misshapen or smaller than usual
• Unusual noises coming from the icemaker

This OEM LG part is also compatible with Sears/Kenmore.