Maytag Axle, Roller, Pulley Parts

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more

• Will not tumble
• Noisy

I've had this dryer apart a few times over the years, always got my parts here. Squeaks and igniter if memory serves. I ordered the two drum rollers that have a bearing in the center..they sit on metal shafts and freeroll. I ordered two..only one was bad but I needed the dryer up in one day, no time to disassemble and decide what to order then wait for parts. Tip: if you order the rollers, there are little washers (nylon?) between the roller and the c clips..don't lose them..they are hard to... Read more

Use the videos on this website here and you can repair most brands. Many are duplicate in design. 1. Unplug the machine. 2. Move it away from a confined area to get more room. 3. Remove lint filter and the two screws that hold the exhaust filter port to the top of the cabinet. 4. Use a putty knife or actually a butter knife and release the top of the cabinet from the main drum housing. You will slide the knife between the top and the main cabinet at the plastic catches. Look for them and you... Read more

Our dryer was making such a load noise that we deemed it unusable. We weren't sure if something would burn up if it continued like it was. So I checked a few articles on the internet and everything pointed to most likely the drum belt. Ours looked a little worn but not really that bad so I got the part. I then followed the repair video that AppliancePros had posted for my model (which was great) and installed the belt. Still squeaking. So I went on to #2 on the list of possible problems, the... Read more

Replaced Read more

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more

Watche videos on their website - very good! Read more

Snaped off and snaped on. Read more

I was repairing my daughter's WDT730pahz0 Whirlpool dishwasher. The bottom dish rack set of wheels was very easy to install. The replacements for the upper set of wheels is different than the originals. In my opinion, the replacements are far superior to the original parts. The problem, as many have pointed out, is that there are no instructions on how to install the new parts. I worked for 15 minutes, attempting to put the pieces together and then install them on the dishrack. That was a... Read more

I ordered 1 assembly first and then another broke. so I ordered 2 more and replaced 2 more. The 4th was replaced last summer. I should have ordered 4 and replaced all when the 1st one failed. Read more

Slide diswasher out to reach the two screws that hold rollers. Reverse prcess, all done. Read more

I removed the front panel of the dryer by removing 2 screws and lifting it up and out. Then I removed 4 screws from the bracket holding the tub in place. I had previously removed the 4 screws from the rear inspection cover so I reached in and released the spring loaded belt that turns the tub and then removed the idler pulley wheel. The tub just lifts out at that point, exposing the 2 Drum support rollers in the rear. I removed the 2 rear drum support rollers and decided to order 2 of... Read more

• Will not agitate
• Burning smell

The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more

Parts snapped into place very easily. Appliance Parts Pros have always delivered on the right part, timely delivery and videos to help. I wouldn't go anywhere else. Read more

I replaced drum rollers, axle shafts and front bearing kit. Still had noise. Ordered Idler Arm, Belt Tension Pulley & Washers. I ordered parts at 3:30 pm on a Wednesday, received new parts at 11:30 am Thursday. The instructions & videos were very simple to follow and provided excellent tips. Back up and running with silence in an 1/2 hour. My 13 year old dryer is running like new again. Way cheaper than calling a repairman. Read more

Tipped the dishwasher on to its front, loosened the drain hose clamp and pulled the hose off. Then unscrew the fill hose which looks like a garden hose adapter. Cut the zip tie on the drain hose and take note of how both hoses are routed, then pull both hoses out the back of the dishwasher. Insert new hoses and route them correctly and hook everything back up. Couple of notes, I didn't have to take off the outer cabinet to do this repair. Get plenty of towels because a lot of water can get... Read more