Maytag Cap Or Cover

This acoustic fiber is the sound-absorbing insulation used in a refrigerator's machine compartment. Replacing a missing or damaged pad reduces operating noise from the compressor area and helps maintain the unit's intended sound levels.

• Absorbs and dampens compressor and condenser fan noise from the rear machine compartment
• Helps reduce vibration resonance transmitted through the cabinet
• Restores sound control when original insulation is torn, saturated, or missing
• Common symptoms: increased humming, buzzing, or rattling from the back or bottom of the refrigerator

• Disconnect power and pull the refrigerator forward for rear access
• Remove the lower rear access panel and note the insulation's placement/orientation
• Position the new pad in the same location; keep clear of coils, wiring, airflow paths, and moving parts
• Reinstall the access panel and restore power; verify no contact or obstruction

White decorative bezel that covers the lid lock mechanism on top of your washer. Replace if cracked, scratched, discolored, or missing from wear.

Replacement flip-up door that covers the lint screen opening in your dryer's front bulkhead. Needed when original door is cracked, broken, or missing.

White screw cover cap for refrigerator door handles. Replaces missing, cracked, or yellowed covers. Installs on handle mounting screws for a clean finish.

Grey decorative cap that covers the water filter housing on side-by-side refrigerators. Replace if cracked, broken, or missing for a finished look.

Trim piece that conceals the door hinge and mounting screws. Replace your cracked, broken, or missing hinge cover to restore a clean finished look.

Secures the agitator to the drive shaft in top-load washers. Replace this collar if it's cracked, worn, or missing to restore proper agitator alignment.

Missing or cracked cap letting water into the agitator? This protective cover seals openings and fasteners, preventing leaks and debris buildup. Easy DIY fix.

White plastic cap that secures the water filter in place. Replace if cracked, broken, or missing to properly hold your refrigerator's filter cartridge.

This cap is a small protective cover used in select appliances. It helps secure and seal its mating component, preventing leaks, debris intrusion, or loosening during normal operation.

• Maintains a secure seal/cover over the designated fitting or opening
• Helps prevent leaks and contamination in the covered area
• Can resolve issues like minor leaks, loose or missing cap, or rattling noises
• Restores proper fit and finish after the original cap is lost or damaged

• Disconnect power and shut off water or gas supply before servicing
• Note the orientation of the original cap for correct placement
• Hand-tighten only unless the OEM specifies otherwise; do not overtighten
• Inspect the mating surface or threads for damage before reinstalling

Secures the water filter in its housing and maintains a watertight seal. Replace when the original cap is cracked, stripped, or missing.

This replacement cover shields and finishes a designated area of your appliance, protecting internal components from dust, moisture, and accidental contact. Replace a cracked or missing cover to maintain proper operation and a clean, finished look.

• Protects internal parts from debris and moisture intrusion
• Restores intended airflow/containment and component protection
• Helps reduce rattles or vibration from loose or broken trim
• Common signs it's needed: cracks, broken tabs, loose fit, or exposed components

• Disconnect power; also shut off water supply
• Retain and reuse original screws/clips unless your model specifies otherwise
• Align tabs and mounting holes carefully to avoid stress on plastic
• Do not overtighten fasteners; snug by hand to prevent cracking

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement door restores a secure close and proper sealing for your appliance. Replacing a damaged or misaligned door helps ensure safe operation and correct latch/switch engagement for reliable everyday use. What it does:

• Provides the closing barrier for the appliance cabinet to maintain proper containment (heat, air, steam, or moisture as designed)
• Aligns with hinges and latch/door switches for correct interlock and operation
• Helps prevent leaks and drafts and protects the interior from damage
• Can address issues such as difficulty closing, visible cracks/dents, poor sealing, or the unit not starting/stopping when the door is moved

• Includes 1 door

• Disconnect power before servicing; also shut off gas or water if applicable
• Support the door during removal/installation; a second person may be needed for larger/heavier doors
• Transfer any reusable hardware (hinge pins, screws, nameplate/trim) from the original as needed
• After installation, verify alignment, latch engagement, and seal/gasket contact; test operation

• Finish, handle style, and configuration are model-specific—ensure the correct match

Replaces cracked, broken, or missing refrigerator component cover. Protects internal parts from dust and spills. Restores proper fit and enclosure.

This replacement cover restores the appliance's finished appearance and protects internal components from dust and debris. It's a direct-fit exterior trim piece designed to replace a cracked, broken, or missing cover. What it does:

• Protects internal components and wiring from debris and accidental contact
• Restores the appliance's cosmetic appearance and helps maintain sealing
• Helps reduce dust buildup in the covered area
• Replaces damaged or missing trim that can expose sharp edges or hardware

• Disconnect power (unplug or switch off circuit breaker) before beginning work
• Basic hand tools may be required; follow for panel removal/replacement
• Handle carefully to avoid scratching the finish and watch for sharp edges
• Replace with manufacturer-recommended fasteners