Maytag Hinge Parts

This top door hinge secures the refrigerator door to the cabinet and lets the door pivot smoothly. Replace a worn hinge to restore proper door alignment and even sealing for better cooling performance. What it does

• Supports the top of the refrigerator door and provides the pivot point for opening and closing.
• Helps keep the door aligned so the gasket seals properly and cold air stays inside.
• Worn or damaged hinge can cause door sag, uneven gaps, rubbing, or noisy operation.
• Restoring the hinge can reduce stress on the door and other hinge components.

• One top door hinge.

• Basic hand tools are usually required; support the door while removing or installing hinges to prevent injury or door damage.
• Disconnect power only if working near electrical components; this hinge replacement typically does not require electrical disconnection.
• If the door was removed, recheck alignment and gasket contact after reinstalling; adjustments may be needed.
• Follow OEM instructions and use proper safety equipment.

This door hinge replaces a worn or damaged refrigerator door hinge to restore proper door alignment and smooth opening. It helps the door sit squarely and close reliably to maintain a good seal. What it does:

• Supports and pivots the refrigerator door so it opens and closes smoothly
• Corrects door sag or misalignment that can cause gaps or uneven sealing
• Reduces rubbing or binding between the door and cabinet
• Helps prevent cold air loss from a door that won't fully close

• One door hinge

• Disconnect power to the appliance and remove food from the door shelves before starting
• Support the door while removing hinge fasteners to avoid dropping the door or injuring yourself
• Use appropriate hand tools; avoid over-tightening fasteners when reinstalling

This hinge secures and guides a refrigerator door on its pivot, helping the door open and close smoothly while maintaining proper alignment and seal. It's a direct-fit replacement when the original hinge is worn or damaged. What it does:

• Replaces a worn or broken door pivot to restore proper door movement and alignment
• Prevents sagging or binding that can stop the door from closing fully
• Helps maintain an effective door seal to protect cooling performance
• Works as the mechanical mounting point between the door and cabinet

• Basic hand tools are typically required; support the door while removing and installing the hinge
• Follow manufacturer guidance for torque and alignment; adjust door leveling as needed after installation
• Disconnect power and remove contents from the door if required for safe handling

This door hinge replaces a worn or damaged refrigerator door pivot to restore smooth opening and secure door alignment. It provides a stable mounting point so doors open and close without sagging or binding. What it does:

• Supports the refrigerator door and keeps it aligned on the cabinet
• Enables smooth pivoting action for opening and closing the door
• Commonly used to fix door sag, sticking, rubbing, or uneven gaps
• Works with original mounting hardware locations to maintain correct seal

• Unplug the appliance or disconnect power before starting work
• Remove food and secure the door; have a helper support the door during removal/installation
• Use basic hand tools; avoid over-tightening fasteners to prevent damage
• Check door alignment after installation and adjust as needed for a proper seal

The Door Hinge (RH) is an OEM replacement part for Whirlpool dishwashers. This hinge is installed on the right-hand side of the dishwasher door, allowing it to open and close smoothly while maintaining the proper tension and alignment. The hinge plays a crucial role in ensuring the door seals securely during operation, preventing leaks and enabling efficient cleaning performance.

Common causes include regular use leading to wear and tear, accidental impacts, or exposure to moisture, which can contribute to rust or corrosion.

Symptoms of a bad door hinge include:

• The dishwasher door not closing completely
• Difficulty opening or closing the door
• A sagging or misaligned door
• Unusual noises when moving the door

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replacement door hinge designed to restore proper alignment and smooth opening for compatible refrigerator doors. Replaces worn or damaged hinges to reduce sagging, rubbing, and uneven closing for better seal and operation. What it does:

• Supports and pivots the refrigerator door for smooth opening and closing.
• Restores correct door alignment to improve gasket contact and cold-air seal.
• Stops door sag, uneven gaps, or rubbing against the cabinet.
• Helps eliminate noisy or stiff door movement caused by a worn hinge.

• Disconnect power to the appliance and remove food from the door area before starting.
• Support the door securely while removing and installing the hinge to prevent dropping or damage.
• Reuse original fasteners only if undamaged; replace any stripped or corroded hardware.

Top hinge assy-rh gal

This door hinge supports and pivots the appliance door so it opens smoothly and closes securely. Replacing a worn hinge restores proper alignment and sealing to help the door latch correctly and operate as designed.

• Provides the pivot point and maintains door alignment
• Helps ensure smooth opening/closing and proper latching
• Supports a tight seal to prevent gaps, rattles, or temperature/moisture loss
• Typical failure signs: door sags, binds, squeaks, or won't stay closed/aligned

• Disconnect power before service; wear gloves to protect from sharp edges
• Support the door and control any spring tension; remove mounting hardware and the old hinge
• Install the new hinge in the same orientation; transfer any reusable hardware
• Adjust as needed

This door hinge supports and guides the appliance door so it opens and closes smoothly and stays aligned with the latch and gasket. Replacing a worn hinge restores proper fit and closing action to reduce rubbing and poor sealing.

• Provides the pivot point and supports the door's weight during operation
• Maintains alignment for an even gap and consistent seal
• Helps correct sagging, scraping, or a door that won't close flush
• Common signs of wear: bent/cracked hinge, squeaking or popping, misalignment

• Disconnect power before servicing and support the door to prevent strain or damage
• Remove mounting fasteners; transfer any reusable screws, spacers, or covers from the old hinge
• Install and snug fasteners, then check door alignment and closure; adjust as needed
• Open and close the door several times to verify smooth operation and recheck fasteners

This oven door hinge restores smooth, controlled door movement and a proper seal. Worn hinges can cause a sagging door, poor closure, or binding—replacing the hinge helps maintain safe operation and consistent cooking performance.

• Supports the oven door with a spring mechanism for controlled opening and closing
• Helps pull the door tight against the gasket for an effective seal when closed
• Works with the opposite hinge to keep the door aligned and stable
• Common symptoms include door not closing fully, sagging or dropping, hard-to-open/close action, or heat escaping around the door

• Disconnect power and allow the oven to cool completely before servicing
• Remove the door following your model's instructions; engage hinge locks or use retaining pins if provided
• Replace the hinge in the same orientation; ensure hinge arms are fully seated in the receivers
• Reinstall the door and verify smooth motion and a complete seal

This oven door hinge restores smooth, controlled movement so the door opens easily and closes fully for a reliable seal. Replacing a worn hinge helps reduce heat loss and supports consistent cooking performance and safe operation.

• Provides the pivot and spring-assisted action for opening and closing the oven door
• Helps pull the door closed and hold it at intended stop positions
• Maintains even gasket contact to keep heat inside the cavity
• Common symptoms of a failing hinge: door won't close fully or sit flush, drops or slams open, binds or pops when moving, or shows an uneven gap

• Disconnect power and allow the oven to cool completely before servicing
• Support the door; open to the removal position and release hinge locks, then lift the door off
• Use caution—hinge springs are under tension; wear hand and eye protection
• Install in the same orientation and verify door alignment and smooth operation after reassembly

This door stop bracket limits how far the appliance door opens. Replacing a worn or bent stop restores proper door swing and helps protect hinges and nearby surfaces from damage. What it does:

• Controls the door's opening range to prevent overextension
• Helps protect hinges and cabinet/adjacent surfaces from impact
• Supports consistent door alignment and smoother operation
• Common symptoms: door swings too far, hits a wall/cabinet, visible wear or broken stop, loud clunk at full open

• 1 door stop bracket

• Disconnect power to the appliance before servicing
• Support the door to avoid hinge strain when removing fasteners
• Note the bracket's orientation; transfer/reuse existing hardware as directed by your IPL
• After installation, verify door alignment and sealing, and test full open/close travel

This door hinge secures and guides the appliance door so it opens and closes smoothly and stays aligned. It replaces a worn or damaged hinge to restore proper door operation and prevent sagging or gaps. What it does:

• Provides pivot support so the door swings smoothly and stays in position
• Keeps the door aligned to form a proper seal when closed
• Prevents sagging, dragging, or uneven closing caused by a broken hinge
• Works as the mechanical connection between the door and cabinet/frame

• One door hinge

• Disconnect power (or unplug the appliance) before starting any repair
• Support the door while removing hinge fasteners to avoid injury or damage
• Use proper tools and tighten fasteners securely; avoid over-tightening

The Door Hinge is an OEM component specifically designed for Whirlpool refrigerators. As an integral part of the refrigerator door, it provides a rotating mechanism that allows for smooth opening and closing access to the fresh food and freezer compartments. 

The hinge contains precisely engineered components including springs, brass pins, and roller bearings that ensure quiet, balanced movement. It helps the door hang securely while accommodating a wide range of opening angles.

Symptoms of a bad hinge include: 

• Noisy squeaking or grinding noises coming from hinges
• Difficulty in opening or closing refrigerator doors  
• Doors that do not stay in desired positions 
• Visual cracks, chips, or other exterior damage to hinges

This Whirlpool OEM hinge replacement will restore reliable door operation. It is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore refrigerator models.
 

The Lid Hinge is an OEM part for Whirlpool washers. It is specifically designed to be the left-side hinge for the washer lid, allowing for smooth opening and closing of the lid. The lid hinge ensures proper alignment and stability of the lid, providing easy access to the washer drum.  

A bad lid hinge can occur due to regular wear and tear, accidental damage, or mishandling. If you notice symptoms such as the lid not closing properly, difficulty in opening or closing the lid, or excessive movement or wobbling of the lid, it may be time to replace this part.

Symptoms of a bad lid hinge include:

• Lid not closing properly
• Difficulty in opening or closing the lid
• Damaged spring

Restore your Whirlpool washer's lid by replacing the worn or damaged lid hinge with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.