Maytag Hose Or Tube

The Refrigerator Drain Connector is an OEM part for Whirlpool refrigerators. It is responsible for directing water and condensation from the evaporator fan coil and defrost into the drain pan. 

Causes of a bad drain connector can include cracks, breaks or deformations caused by repeated thermal cycling or impact damage. Mineral or lime buildup inside the connector over many years can also restrict water flow.

Symptoms of a bad drain connector include:

• Water or condensation leaks around the connector area 
• Puddles or watermarks on the floor behind the fridge
• Slow drainage of water from the evaporator fan coil
• Mold or mildew growth near the connector or drain area

This replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Icemaker Fill Tube is an OEM replacement part for Whirlpool refrigerators. It delivers water to the icemaker, allowing it to produce ice cubes. It is responsible for directing water from the water inlet valve to the icemaker tray, where it freezes into ice cubes.

A bad fill tube can occur due to wear and tear, blockages, or damage. If you notice symptoms such as no ice production, leaking water, or ice cubes with an unusual shape or size, it may be time to replace the fill tube.

Symptoms of a bad fill tube include:

• No ice production or limited ice output
• Leaking water around the icemaker area
• Irregularly shaped or oversized ice cubes

Repair your refrigerator by replacing the faulty or damaged fill tube with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This outer drain hose routes wastewater from your washer to the household standpipe or sink. Replacing a cracked, kinked, or clogged hose restores proper draining and helps reduce leaks at the back of the appliance.

• Carries discharge water from the drain pump outlet to the home drain connection
• Damage such as splits, pinholes, or hardening can cause leaks during the drain cycle
• Kinks or blockages can lead to slow or no draining and water left in the tub
• Visible wear, brittleness, or recurring drain errors are common signs the hose needs replacement

• Disconnect power and turn off water supply before servicing
• Pull the washer forward to access; keep towels or a pan ready for residual water
• Detach the old hose from the pump/outlet and household drain; transfer and reuse clamps or brackets as required by your model
• Route the new hose without kinks, secure all connections, follow your model's manual for drain placement, then run a test drain and check for leaks

Supplies water to the spray arm.

The Drain Hose is an OEM part for Whirlpool dishwashers. It serves as the connection that allows dirty water to exit the dishwasher tub and flow into the water drain system after each wash cycle. The hose transports wastewater from inside the dishwasher out through the standpipe.

Causes of a bad drain hose can include mineral or food debris buildup blocking water flow within the hose, cracks or breaks in the plastic material from repeated bending, or a loose or damaged hose clamp connection.

Symptoms of a drain hose failure include:

• Standing water remaining in the bottom of the tub after a cycle
• Puddles or leaks developing near or underneath the dishwasher
• Water failing to properly drain during the designated drain portion of cycles
• Kinks or sagging appearing in the hose affecting water drainage

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Size: 1/4 inch. Nut for plastic water line.

Ice maker water line: 1/4x 8ft.

This water outlet tube routes water within the appliance's water system, maintaining a secure, leak-resistant path to its outlet. Replace a cracked, kinked, or leaking tube to restore proper water flow and prevent leaks. What it does:

• Directs water from internal plumbing to the designated outlet/assembly
• Maintains a sealed connection to help prevent drips and leaks
• Typical failure symptoms: water leaking inside or onto the floor; weak or no water flow; visible cracks, kinks, or a loose fit at connections

• 1 water outlet tube

• Disconnect power and shut off the water supply before servicing
• Note tube routing and connection points; remove any clips/fasteners as needed and pull the old tube free
• Fully seat the new tube into each port; ensure any existing seals or clips are positioned correctly
• Run a short test cycle and check all joints for leaks

This water supply tube connects at the inlet water valve, routing water through your appliance's water system. Replacing a brittle, cracked, or kinked line helps restore reliable, leak-free operation and proper water flow. What it does:

• Carries water from the inlet valve to the designated component (such as dispenser, icemaker, or filter housing, depending on model)
• Helps maintain proper water pressure and uninterrupted flow
• Common symptoms include leaks at the back/bottom, slow or no water at the dispenser, or an icemaker not filling
• Addresses visible cracks, brittleness, or kinks in the existing tubing

• 1 water supply tube

• Disconnect power and shut off the household water supply; relieve line pressure by dispensing water
• Place a towel to catch residual water and note the original routing before removal
• For push-in/quick-connect fittings, insert fully and tug back to verify engagement; if using compression fittings, tighten snugly without overtightening
• Turn water on and check all connections for leaks before restoring power

This water tube routes the household water supply from the inlet valve to the refrigerator's water filter. Replacing a cracked or kinked line restores proper dispenser and ice maker flow and helps prevent leaks around the filter assembly.

• Carries water from the inlet valve to the filter housing
• Helps maintain proper, unrestricted flow to the dispenser and ice maker
• Typical failure symptoms: leaks, visible cracks or kinks, reduced dispenser flow, no water at the dispenser, slow or no ice production

• Disconnect power and shut off the water supply before servicing
• Dispense water to relieve pressure and place a towel to catch residual water
• Note the routing; release the tube from retainers and fittings carefully
• Fully seat the tube in push-to-connect fittings, avoid sharp bends, restore water, and check for leaks

This coupler and hose assembly connects your portable dishwasher to the sink faucet during operation. It supplies fresh water and returns drain water to the sink, helping stop leaks and restore reliable filling and draining.

• Provides a quick-connect link to a compatible faucet adapter for temporary hookup
• Carries incoming water to the dishwasher and routes drain water back to the sink
• Maintains a secure, leak-resistant seal during wash and drain cycles
• Replace if the coupler won't attach or stay on the faucet, hoses are cracked/kinked, or you see leaks and poor fill/drain performance

• Unplug the appliance and turn off water before service
• Verify the faucet adapter and O-rings are in good condition; hand-tighten only—do not overtighten with tools
• Route hoses to avoid kinks and sharp bends
• Open the faucet slowly and run a short test cycle; check all connections for leaks

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

This replacement hose routes liquid or air between internal components, maintaining a secure, leak-resistant path. Replace a brittle, cracked, or clogged hose to prevent leaks and restore proper flow and sensing performance.

• Provides a sealed pathway between components such as the pump, tub, valve, drain path, or pressure system
• Helps maintain correct water flow or pressure/level sensing
• Common symptoms: leaks, kinks/cracks, standing water, slow/failed drain or fill, related error codes
• Restores reliable connections when used with properly seated clamps

• Disconnect power and shut off water supply before servicing; allow hot parts to cool
• Place towels or a shallow pan to catch residual water
• Note routing and clamp locations; transfer or replace clamps as needed and seat the hose fully on fittings
• Test for leaks with a short cycle and re-check all connections

Size: 90 inches long. To order hose extension use 12001585. To order siphon break use 76660.

This spigot routes water from the internal supply to the dispenser outlet, delivering a controlled stream. Replacing a cracked or worn spigot helps restore proper dispensing and reduces drips or leaks at the dispenser area.

• Directs water from the internal tubing/reservoir to the dispenser outlet
• Maintains a defined flow path to help prevent splashing and after-drip
• Common symptoms of failure: dripping at the dispenser, slow/erratic flow, leaks inside the door, or visible cracks at the outlet
• Replace if damaged, leaking, or obstructed by mineral buildup

• Unplug the appliance and shut off the household water supply
• Dispense water to relieve line pressure before replacement
• Access the dispenser; note tubing orientation and fully seat/secure connections
• Restore water and power; flush the system and check all joints for leaks

This flume hose kit replaces the flexible hose that routes water from the dispenser/fill flume into the washer tub. Restoring a tight, unobstructed hose helps prevent leaks and ensures detergents, bleach, and softener are carried into the wash.

• Directs fill/dispenser water from the flume to the tub during wash and rinse
• Restores proper flow so dispenser compartments empty correctly
• Helps prevent leaks caused by splits, brittleness, or loose connections
• Typical symptoms: water on the floor, dispenser not draining, weak flow into tub, musty odor near dispenser

• Disconnect power and shut off water supply before servicing
• Access the dispenser/flume area by removing the top or control panel per your model
• Note hose routing; transfer and secure clamps; avoid kinks and rub points
• Run a quick fill/rinse to check for leaks at both connections after installation