Maytag Washer Gasket & Seal

Replaced clutch assembly, gearcase input shaft seal and motor coupler. When I disassembled the washer I realized the shaft seal on the top of the gearcase was leaking and not the input shaft seal. So had to order more parts before I could finish this job. Altogether I replaced agitator dogs, both seals on the gearcase, the clutch assembly and the motor coupler. Agitator dogs replacement is a very easy job, no tools required, takes less that 5 minutes and made a huge difference with how well... Read more

• Noisy

I just wanted to put my experience here for all to see. I have a Maytag Neptune, MAH5500BWW, one of the original ones. I bought it back in 2002 and it has done many many loads of wash faithfully. So when the bearings started to get loud I thought it best to replace them, the seal kit and the belt. I did my research as best I could and decided to order the OEM parts from an appliance supplier. If you are replacing the bearings, watch on line videos prior to performing the job. It will... Read more

First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available.... Read more

Used the parts and youtube video from your company. Read more

I ordered the dispenser and the distribution nozzle since the old one was in bad shape. I also replaced the boot since I had to take the entire machine apart and it is 20 years old. I watched your videos on you tune to learn what to do. I recently lost my job and really could not afford to hire someone to fix my washer. I have to say it wasn't that hard to do and my wife was so happy that I was able to fix it myself! I probably saved $200 or $300 in service calls and labor on top of what they... Read more

Replaced mounting stem and tub bearings Read more

With the basket out of the dishwasher, the plastic parts basically snap on and off... popped the broken parts off and the new parts on. The 2 wheel and mount assemblies were a little more complicated. The video on the website advises to disconnect the supply line and drain line... I didn't have to do this. I just pulled the dishwasher out of its cabinet a little over a foot and removed the 2 screws holding each assembly in place and removed them. The previous gaskets (2 PER ASSEMBLY)... Read more

Replaced the bellow without having to remove any of the panels. Was able to make the repair from the front of the machine by just removing the 2 clamps that hold the bellow seal in place. Read more

This was some repair! My SG1000 stackable is over 30 years old and was purchased second hand. I've replaced many parts in the dryer section, but besides a water inlet, this was my first repair to the washer. All of a sudden it started making a terrible noise and was not agitating the clothes. The spin cycle worked fine. I first replaced the two belts on the bottom, but when I removed the old ones I realized they did not look terribly worn and weren't the cause. Many stories on here indicated... Read more

Read articles and watched How-To video on AppliancePartsPros.com. Videos were very informational and parts arrived very quickly! Read more

Removed agitator, inner washer barrel, and agitator shaft then drained all the water and emulsified oil out of the transmission. Filled the transmission with new oil and then replaced the worn agitator shaft, shaft collar, shaft o-ring and stem sealing system. Read more

Found the wonderful parts diagrams you most generously share online and a couple of YouTube videos . I determined it should be repairable. In my cast the agitator shaft was frozen (rusted) in place. I was very fortunate to have been able to eventually remove it with the use of a lot of BP penetrating oil and heat. Long and short the replacement parts fit perfectly and the washer is running like new. Special thanks to the online support make my repair possible. Read more

Replaced the coupler gasket. No leaks now. Read more

• Leaking

Replaced with new part ordered from store Read more