Maytag Washer Parts

• Lid or door won't close

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more

We ordered parts from appliance parts pros and I fixed it. Read more

After the part arrives, I was double check to make sure I got the right part. Importantly, unplug the electrical power first before do anything, also turn off the water hose for safety. Then removed 4 screw out side panel and 2 screw in side to get lose. After all, replaced a new part and put all panel and screw back together. Finally, plug in electrical power then a water hose and test a new part just installed. So far so good, seem like everything was function OK. Again, thanks for your web... Read more

I replaced the switch, the plunger, plunger guide and the lid cam, but the cam still didn't turn on the switch. Turned out someone had stood on the washer and bent the lid slightly, not enough to notice, but since I had ruled out just about everything else I started looking at the lid itself. I ended up bending it back close to it's original shape and now it works fine. I guess I learned a few things about washing machines though. One lesson is when you pull off the controls, the hose leading... Read more

I replaced the drain pump and hose which had a flapper valve that wasn’t sealing properly. Easy repair. Took about 15 minutes total and my washing machine is Soooo much quieter!!! Read more

Symptoms: Machine was spinning and spitting a dark colored oil in a circular pattern on the floor under the machine. No strange noises, just messy. Researched issue, Gear-case bad, seal deteriorated and not preventing water from entering gear-case. The additional cam, belt etc I had replaced due to the amount of oil and transmission residue attached to them. Ordered parts, EVERYTHING parts-wise that is needed is included in gear-case package. **NOTE: You WILL need to get a whirlpool spanner... Read more

With the basket out of the dishwasher, the plastic parts basically snap on and off... popped the broken parts off and the new parts on. The 2 wheel and mount assemblies were a little more complicated. The video on the website advises to disconnect the supply line and drain line... I didn't have to do this. I just pulled the dishwasher out of its cabinet a little over a foot and removed the 2 screws holding each assembly in place and removed them. The previous gaskets (2 PER ASSEMBLY)... Read more

REPLACED Read more

Took less than half an hour to complete repair. Saved $100 service call!! Read more

Ordered a new one and put it in. Read more

I replaced the switch, the plunger, plunger guide and the lid cam, but the cam still didn't turn on the switch. Turned out someone had stood on the washer and bent the lid slightly, not enough to notice, but since I had ruled out just about everything else I started looking at the lid itself. I ended up bending it back close to it's original shape and now it works fine. I guess I learned a few things about washing machines though. One lesson is when you pull off the controls, the hose leading... Read more

Ordered a new timer from Appliance Pros.com Read more

First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in... Read more

Bought a new one and screwed one on. Read more

• No hot or cold water

I order the part from appliance parts recieed it in one day and it was repaired the next day so simple watched video thanks to you all is well i highly recommend you to anyone barbara mcallister Read more