Range / Cooktop / Oven Control Board

The Oven Control Board is an OEM part for Whirlpool ovens. It regulates and controls the various functions and settings of your oven, including the oven's temperature, timers, and cooking modes.   

A bad oven control board can occur due to electrical malfunctions, power surges, or component failure. If you notice symptoms such as an unresponsive control panel, error codes displayed on the screen, or erratic heating and temperature fluctuations, it may be time to replace the oven control board.

Symptoms of a bad oven control board include:

• Unresponsive control panel
• Error codes displayed on the screen
• Erratic heating and temperature fluctuations

Restore your oven by replacing the faulty or malfunctioning oven control board with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This electronic control board is the "brain" of the dishwasher, coordinating cycle timing and powering key components. Replacing a failed board can restore normal operation when the unit won't start, stops mid-cycle, or behaves erratically. What it does:

• Manages cycle timing and sequences based on selected options
• Distributes power to the circulation pump, drain pump, water inlet valve, heater, and dispenser
• Monitors inputs from sensors and the door switch to advance/complete cycles
• Faults can present as unresponsive controls, won't start/finish cycles, random resets, or error codes

• 1 electronic control board

• Disconnect power at the breaker before servicing; shut off water supply if accessing the lower compartment
• Use anti-static precautions; handle by the edges and avoid touching connector pins
• Access location varies by model; photograph wiring and transfer one connector at a time
• After installation, run the dishwasher's diagnostic/service cycle to verify operation

This electronic oven control board governs bake/broil functions and the display for Frigidaire-made ranges. Replace it to restore oven heat, accurate temperature regulation, and responsive controls when the original control fails. What it does

• Controls power to the bake and broil element/igniter and times oven cycles
• Monitors the oven sensor and maintains the set temperature
• Receives keypad inputs and drives the clock/temperature display
• Common symptoms: oven won't heat or overheats, display dead/dim, unresponsive buttons, intermittent shutoff, or error code on the display

• 1 electronic control board

• Disconnect power at the breaker before servicing; verify no voltage at the range
• Access the control through the backguard/control panel; photograph wiring for reference
• Handle the board by the edges to avoid static damage; move connectors one at a time
• Transfer the existing keypad overlay/trim and any mounting hardware from the old board

This oven control board manages the electronic clock/timer and controls bake and broil functions. Replacing a failed board restores accurate temperature control, display, and keypad responsiveness so your range or wall oven heats and operates reliably again.

• Directs power to bake and broil elements based on user settings and oven sensor feedback
• Common symptoms: oven won't start or won't heat; temperatures are erratic or inaccurate
• Display is blank, dim, frozen, or keypad buttons are unresponsive
• Repeated fault/error codes or beeping from the control; intermittent cycling or shutdown

• Disconnect power at the breaker or fuse box before servicing; verify no voltage is present
• Use anti-static precautions and handle the board by the edges
• Photograph/label wiring; move connectors one at a time to the same locations on the new board; reuse original mounting hardware
• Restore power, set the clock, and run a short bake test to confirm proper operation

This clock control board is the electronic brain of your oven. It powers the display, reads keypad inputs, and controls bake/broil functions so you can set temperatures, timers, and cycles reliably. What it does

• Drives the time/temperature display and kitchen timer
• Interprets keypad inputs for bake, broil, and clean
• Sends power to heating circuits via onboard relays
• Manages alarms and fault monitoring

• Blank, dim, or garbled display
• Buttons unresponsive or erratic
• Oven won't start or won't heat despite good elements and power
• Random beeping or fault/error codes

• 1 electronic clock/control board

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use anti-static handling; avoid flexing or touching component pins
• Photograph and label all wire connections before transfer
• If your model uses a separate overlay/keypad membrane, carefully transfer it from the old board

Electronic clock control for the oven/range. This board drives the display and manages bake/broil commands, restoring accurate timekeeping and dependable oven controls when the original control has failed.

• Governs oven operations by processing keypad inputs and signaling the heating circuits for bake and broil
• Displays clock, timer, and status information
• Monitors system feedback and can trigger fault alerts when issues are detected
• Common failure signs: blank or flickering display
• Oven won't start, won't respond to settings, or shows recurring control fault codes

• Disconnect power at the breaker and verify no voltage before servicing
• Use anti-static precautions; handle the board by the edges
• Note wire/connecter locations and transfer them one at a time; reuse any brackets/trim your model requires
• After installation, set the clock and run a test bake/broil; clear stored codes if applicable

This OEM part is a power control board. The power control board provides power to the electronic oven control board. If the oven is no longer turning on, or the digital display is no longer visible, this could mean it's time to replace the power control board. Luckily this is a relatively simple process.To begin, make sure to turn off the power to the oven by unplugging it or shutting off the circuit breaker. Then proceed to remove the upper back panel. Once removed locate the power control board and remove the wire harness and wires attached to it. Be sure to take note of the orientation of the wires to place them into the correct terminals on the new board. Attach the wires to the new board and snap the new board back in place. Resecure the back panel and put the oven back in place.This genuine replacement part is sold individually and is compatible with Bosch, Thermador, and Gaggenau ovens.

This oven control board is manufactured by Whirlpool. It is an electronic component and is responsible for monitoring and controlling the oven's functions, such as bake, broil, and warm, as well as maintaining the appropriate temperature set by the user. This control board does not include the physical controls for the oven.High heat and exposure to moisture can degrade the control board. This may result in intermittent problems or outright failure of the oven. In both cases, the control board will need to be replaced. Before working on the oven, make sure to unplug it or shut off the circuit breaker. Wear gloves at all times and exercise care when disconnecting/connecting the writing to the board.A genuine OEM part, this control board is sold individually. It fits Whirlpool and KitchenAid branded ovens.

This relay board assembly switches line power to the range/oven's heating circuits under the direction of the electronic control, helping restore reliable bake/broil operation when relays or board components fail. What it does

• Controls power to the bake and broil elements via onboard relays
• Executes low-voltage commands from the control to switch high voltage to the heating circuits
• Failure symptoms can include no heat in bake or broil, one element not working, or intermittent heating
• Burn marks or a stuck/clicking relay on the board may be visible indicators of failure

• 1 relay board assembly

• Disconnect power at the breaker before servicing; this board carries live voltage
• Access location varies by model; photograph and label all wires for correct reassembly
• Handle the board by its edges and observe ESD precautions
• Ensure all connectors are fully seated and the board is securely mounted before restoring power

Due to manufacturer changes please contact our customer service to verify this part is compatible with your appliance.

This electronic oven control board (clock/timer) is the brain of your range/oven, regulating temperature, powering the bake/broil circuits, and managing the display and keypad. Replacing it restores proper heating and responsive controls.

• Governs bake and broil circuits and maintains set temperature using oven sensor feedback
• Displays time/temperature and responds to keypad inputs
• Common failure signs: oven won't heat or start, erratic/inaccurate temps, dead or unresponsive display, repeated beeps or error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the board by the edges and use anti-static precautions
• Photograph/label connectors and transfer wires one at a time to the new board
• Transfer the existing keypad overlay and any brackets as needed, reinstall panel, restore power, and test bake/broil

The Range Main Control Board Assembly is essential for the proper functioning of your range. This genuine OEM part ensures seamless control over all range operations, including temperature settings, burner functions, and indicator lights. Designed specifically for Samsung ranges, it provides a reliable and secure fit, making installation straightforward and hassle-free. The main PCB assembly is built with high-quality components to enhance the performance and longevity of your appliance, allowing you to cook with confidence and precision. If youGÇÖre experiencing unresponsive controls, inconsistent heating, or malfunctioning displays, the Range Main Control Board Assembly offers a dependable solution to restore your rangeGÇÖs functionality. By choosing this genuine OEM part, you are ensuring that your Samsung range operates smoothly and efficiently, maintaining the optimal performance you expect. Trust in this main control board to deliver a user-friendly and efficient cooking experience, keeping your kitchen running flawlessly.

This electronic oven control board manages the oven's heating functions, temperature regulation, and display/clock. Replacing a failed board restores accurate temperature control and responsive controls so your oven can heat and keep time reliably.

• Controls power to bake and broil elements based on user input and sensor feedback
• Regulates oven temperature and cycle timing
• Drives the display and processes keypad/selector inputs
• Common failure symptoms: no heat, won't start, blank/unresponsive display, beeping/error codes, inaccurate oven temperature

• Disconnect power at the breaker before servicing
• Handle the board with ESD care; avoid touching component contacts
• Note/photograph wire positions; transfer connectors one at a time and reuse existing brackets as needed
• After reassembly, restore power, set the clock, and test bake/broil per the service sheet

This electronic oven control board manages bake/broil power, temperature regulation, and the clock/display for the range. Replacing a failed control restores accurate heating, reliable cycle timing, and responsive keypad/display operation.

• Regulates bake and broil element power using feedback from the oven temperature sensor
• Controls oven temperature, cooking cycles, and timing functions
• Operates the clock, display, and keypad interface
• Typical failure symptoms can include no heat or won't start, won't reach/hold set temperature, blank/unresponsive display, or error codes/beeping

• Disconnect power at the breaker before servicing
• Handle the new board by the edges and use anti-static precautions
• Photograph wiring and move connectors one at a time; transfer any mounting brackets and the user interface overlay from the original
• After installation, set the clock and test bake/broil operation

The Control is an OEM part for Frigidaire ranges. It serves as the central control unit for the oven, allowing you to set and adjust cooking temperatures, timers, and other essential functions.

A bad oven control board can be caused by electrical issues, component failure, or damage due to power surges or other factors. When the control board becomes faulty, it can result in issues such as inaccurate temperature readings, unresponsive controls, or failure of the oven to heat up properly.

Symptoms of a bad control board include:

• Inaccurate temperature readings or inconsistent heating
• Unresponsive or malfunctioning control panel
• Failure of the oven to heat up or maintain desired temperature

Replace your faulty oven control board with this genuine OEM part to restore your range.
This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This relay board works with the main control to switch power to high-load oven components. Replacing a failing board can restore consistent heating and reliable performance across bake, broil, and convection functions. What it does:

• Switches high-voltage power to oven elements and fans as directed by the control
• Loss of heat in one or more modes (bake/broil/convection) is a common failure symptom
• Intermittent or erratic heating, long preheat, or heat stopping mid-cycle
• Visible burn marks or heat damage on the board

• Disconnect power at the breaker or fuse box before servicing
• Access location varies by model (rear panel or control compartment)
• Photograph wiring and move connectors one at a time to the new board
• Handle by the edges and use anti-static precautions; reuse existing hardware