Range / Cooktop / Oven Control Board

This electronic control board is the main oven controller. It manages bake and broil relays based on sensor feedback and drives the clock/display, restoring accurate temperature control and dependable cooking cycle operation when the original board fails. What it does:

• Monitors the oven temperature sensor and switches the bake/broil elements via onboard relays
• Controls and displays settings, time, and status; may store or report fault codes
• Coordinates preheat and timed cooking functions supported by the model
• Also referred to as the EOC (Electronic Oven Control)

• One electronic control board

• Disconnect power at the breaker and verify the appliance is de-energized before servicing
• Access is typically through the control panel; photograph and label wires to ensure correct reconnection
• Handle the circuit board by the edges and use ESD protection if available
• Transfer each connector to the matching terminal; if your model uses a separate overlay, carefully transfer it to the new board
• Restore power and run a test bake to ensure proper operation

This OEM part is a relay control board for ovens. An oven relay control board is a circuit board that receives signals from the main oven control board. The relay control board then relays the signal to regulate the oven's essential functions. Over time, a relay control board can become overworked. If the oven is no longer turning on, heating properly, or regulating its temperature, it might be time for a new relay board. Luckily, replacing this part is not a difficult process. To replace the relay board, make sure the oven is unplugged. Gain access to the upper back panel on the back of the range and remove the screws. Once the panel is removed access the relay board and remove the wire harness as well as any individual wires attached to the old board. Make sure to take note of the orientation of the wires. Replug the wires into their correct terminals on the new board and snap the new board back in place. Resecure the upper back panel.This genuine replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore brand ovens.

This electronic oven control board governs your range or wall oven's heating and display functions. Replacing a failed EOC restores accurate temperature control, reliable bake/broil operation, and responsive clock/timer performance.

• Regulates power to bake and broil elements using oven sensor feedback
• Controls set temperatures, preheat, and cycling to maintain heat
• Drives the clock, timer, and status indicators on the display
• Common symptoms: no heat or won't start, won't reach/set temperature, blank or unresponsive display, recurring fault codes

• Disconnect power at the breaker before servicing
• Handle the board by the edges and protect from static discharge
• Photograph wiring; move each connector to the matching terminal and transfer any mounting hardware from the original board
• After installation, run a test bake and verify temperature calibration per the unit's tech sheet

The board housing assembly mounts and protects the electronic control board inside the appliance's control console. Replacing a cracked or heat-damaged housing restores solid support, correct alignment, and reliable operation of the display and keypad.

• Supports and shields the electronic control board within the console
• Provides proper mounting and alignment for the display and keypad
• Helps manage and secure wire/ribbon connectors to reduce strain and vibration
• Typical indications for replacement: cracked or warped housing, broken tabs, loose or misaligned controls, sticking buttons, or rattling from the console

• Disconnect power at the breaker or unplug the appliance; verify power is off
• Remove the control panel/console to access the housing; note screw locations and photograph wiring
• Transfer the existing control board to the new housing; handle electronics with ESD care and avoid overtightening
• Reseat ribbon cables and harnesses fully before reassembly and restoring power

This is an oven control board and clock for electric ranges. The main purpose of this part is to monitor and control the temperature of the oven and the range. This part also functions as a display for time and temperature settings. This part may need to be replaced if the display is no longer lighting up properly or if any part of the display has burnt out or cracked. The part may also be in need of replacing if it is no longer responding to temperature or time commands. When preparing to replace this part, be sure to first unplug the range or shut off the correct circuit breaker that corresponds to the unit. It is also important to wear work gloves to protect the hands while replacing this part.This oven control board is designed for Jenn-Air, Maytag and Amana appliances. It is an authentic OEM replacement part that is directly sourced from the manufacturer. The control board is sold as a single unit.

This electronic oven control board manages the bake/broil circuits and the clock/timer display. Replacing a failed board restores accurate temperature control and responsive keypad/display operation so your range can heat and time reliably again. What it does:

• Regulates power to the bake and broil elements based on temperature sensor feedback
• Interprets keypad inputs and drives the digital clock/timer display and alerts
• Controls oven relays for preheat, maintain-temp, and timed-cook functions
• Common failure symptoms include: no heat or intermittent heating, blank or unresponsive display, beeping/error indications, or oven that won't shut off

• 1 electronic control board

• Disconnect power at the breaker before servicing; verify no voltage is present
• Handle the board by the edges and use ESD protection to avoid static damage
• Note/photograph wire locations; transfer any mounting hardware or overlay from the original as applicable
• After installation, restore power, set the clock, and test all oven modes

This OEM replacement part is an oven control board. The control board serves as the main computer to the oven and controls all its essential functions such as baking, maintaining temperature, as well as turning it on and off. If the oven is no longer turning on, or there is an error code on the digital display, this could mean that the control board is no longer operable. If this is the case, the control board will need to be replaced.To replace this part, start by unplugging the oven. After the power has been shut off, proceed to remove the upper back panel of the range. Once removed gain access to the old control board and snap it out of the locking tabs holding it in place. Take note of the orientation of the wires by taking a photo with a phone camera. Remove the wire harness and individual wires from the old board and place them into the correct terminals of the new board. Snap the new board back in place and re-install the upper back panel.This genuine replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand ovens.

This replacement clock is the electronic control that manages the time display and timer functions on compatible units—and on many models, it also coordinates oven operation. Restore a readable display and dependable controls for everyday cooking.

• Displays time-of-day and runs the kitchen timer
• Interfaces with the keypad; may switch bake/broil relays on applicable models
• Common symptoms: blank, dim, or flickering display; persistent beeping/error codes
• Common symptoms: unresponsive buttons, timer issues, or oven won't start/heat

• Disconnect power at the breaker before servicing; do not work on live circuits
• Handle the control by the edges and use ESD precautions to avoid static damage
• Photograph wiring and move connectors one at a time to the new control
• Reassemble the control panel, restore power, and set the clock

This electronic control board manages the oven's heating functions and the clock/timer display. Replacing a failed controller restores accurate temperature control, reliable cooking modes, and a working display on your range or wall oven. What it does:

• Controls heating element relays based on user input and temperature sensor feedback
• Operates the digital display, clock, and kitchen timer
• Coordinates oven modes such as preheat, timed bake, and self-clean
• Common symptoms of a failing board: no heat or erratic temperatures, blank/unresponsive display, beeping or error codes, inability to start or cancel bake/broil

• 1 electronic control board (controller) assembly

• Disconnect power at the breaker before servicing; this board carries live voltage
• Access through the control panel; remove panels/screws as needed to reach the board
• Move wire connectors one at a time from the old board to the new; take photos for reference
• Use ESD protection and avoid touching circuitry; set the clock and test all oven functions after installation

This OEM replacement part is an oven control board. The oven control board is the primary computer circuit board that controls the main functions of the oven. These functions include turning the oven on as well as adjusting and maintaining the temperature of the oven. Luckily, replacing a control board is a simple process.To replace the board, first, make sure the oven is unplugged. Gain access to the back of the oven and remove the upper back panel. Once the panel is removed, locate the old control board. Take note of the orientation of the wires by taking a photo with a phone camera. Disconnect the wire harness and any individual wires that are attached to the old board. Re-secure the wires into their correct positions. Snap the new board back in place and reinstall the upper back panel.This genuine replacement control board is compatible with Frigidaire Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.

This electronic control board manages your oven's display, keypad inputs, and heating functions. Replacing a failed board can restore responsive controls, proper bake/broil operation, and reliable timing so your range or wall oven works as designed. What it does:

• Interprets keypad inputs and updates the clock/temperature display
• Controls bake and broil circuits via onboard relays
• Monitors the oven temperature sensor to regulate heat
• Runs cooking modes and timers

• 1 electronic control board assembly

• Disconnect power at the breaker before servicing; verify no power is present
• Handle the board by the edges and use ESD precautions
• Note/photograph wire locations; transfer any brackets or supports from the original board
• After installation, restore power and test bake/broil functions to confirm operation

This electronic oven control board governs the oven's cooking functions and the clock/timer. It restores accurate temperature control and a working display so you can set modes and cook times reliably again.

• Regulates the bake and broil circuits to reach and maintain the set temperature
• Drives the display for time, temperature, and status; manages timer and alerts
• Interprets keypad inputs to start/stop cooking modes
• Typical symptoms: no heat or won't start, erratic temperatures, dead or flickering display, unresponsive buttons, repeated error alerts

• Disconnect power at the breaker before servicing to prevent electrical shock
• Access the control panel, label/photograph all connectors, and move them one at a time
• Handle the board by the edges and use ESD precautions; seat connectors fully without forcing
• Transfer the existing overlay and any mounting hardware/brackets if applicable; test a bake cycle after reassembly

This part is a relay control board that is manufactured by Frigidaire. This part is intended to replace a broken or faulty relay control board in various wall oven models.This part is critical for proper appliance functionality as it helps to regulate the oven elements via signals received from the main board. If this part is broken, the user may have trouble operating the oven, or the oven may not power on at all. The appliance should always be entirely disconnected from the power source before making a repair. It's recommended that work gloves are worn when attempting a repair or part replacement. As an authentic OEM replacement part, this relay control board is suitable for use with wall ovens that have been manufactured by Frigidaire, Electrolux, Gibson, and Kelvinator. This part is sold individually and is a genuine part made of high-quality, durable, non-corrosive materials.

This electronic oven control board manages your range's heating and display functions. Replacing a failed control restores accurate temperature regulation, bake/broil operation, and a working clock/timer so the oven heats and responds as it should. What it does:

• Directs power to the bake and broil elements through internal relays
• Monitors the oven temperature sensor and regulates heat to maintain the set temperature
• Provides the clock/timer and status display; interfaces with the keypad
• Typical symptoms: won't heat or stops heating mid-cycle, inconsistent temperatures, blank/unresponsive display, error codes or beeping

• 1 electronic control board

• Disconnect power at the breaker before servicing; this is a line-voltage component
• Use ESD precautions; handle the board by the edges and avoid touching contacts
• Note/photograph wire locations; move connectors one at a time and fully seat any ribbon cable
• Transfer any mounting brackets and the faceplate/overlay from the original control if your model uses them

This is a Whirlpool range control board. It manages and monitors temperatures for the range and features a digital display and user interface buttons. The control board can short out due to power surge or exposure to excessive heat. For example, if the oven's self clean function is run too long or too frequently, parts of the control board could melt or otherwise malfunction.Before installing this part, be sure to cut power to the appliance and allow it to cool completely. The stove may need to be pulled away from the wall to access the screws holding the control panel in place. Remove the screws from each side of the control panel to gain access to the old control board. Disconnect any wire harnesses connected to it and remove any screws mounting it in place before installing the new part.This is a genuine OEM part compatible with ranges manufactured by Whirlpool brands, including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and others. This product is just the panel and contains no additional parts or hardware.

This electronic oven control board regulates and coordinates oven functions on gas ranges—driving the display, processing keypad inputs, and switching relays—so you can set temperatures and cycles reliably. Replacing a failing board restores responsive controls and consistent heating. What it does:

• Controls bake and broil ignition and temperature regulation in gas ovens
• Interprets keypad inputs and updates the display
• Switches power through onboard relays to igniters/valves as directed by sensors
• Common failure symptoms: blank or erratic display, unresponsive controls, oven won't start or heat, or recurring control error codes

• 1 electronic control board assembly

• Disconnect power at the breaker and shut off gas before servicing
• Use ESD precautions; handle the board by its edges
• Access the board behind the control panel; photograph wiring and move connectors one at a time
• Reuse existing mounting hardware; restore power and test oven functions after reassembly

• A faulty oven temperature sensor or keypad/touch interface can mimic control-board issues; test related components before replacement.