Range / Cooktop / Oven Switch

Burner stuck on high or won't heat? This infinite switch controls surface element temperature from low to high. Straightforward repair restores heat control.

Fixes burner stuck on high, won't heat, or uneven heating. This infinite switch regulates surface element power for precise temperature control.

If your triple burner stays on high or won't adjust temperature, this infinite switch restores precise heat control for small, medium, and large rings.

This control-panel switch restores reliable on/off control of a selected function on your range or wall oven. Replacing a worn or intermittent switch helps ensure the appliance responds consistently when you toggle that function.

• Directs power to the associated circuit when switched on or off
• Common symptoms: function won't turn on/off, intermittent operation, or the switch feels loose/sticks
• Helps restore positive, consistent control from the backguard/control panel

• Disconnect power at the breaker before servicing
• Access the switch from the control panel/backguard; retain screws/clips
• Label/photograph wire positions and transfer leads one at a time to the new switch
• Ensure firm terminal connections, reassemble, restore power, and test operation

If your range burner won't heat, cycles incorrectly, or buzzes when turned on, a faulty infinite switch is likely the cause. Moderately easy DIY repair.

Burner stuck on high or won't regulate temperature? The infinite switch controls heat levels. Common DIY repair, typically 10 minutes to install.

Fix sparking or non-working igniter switches with a new switch harness. Connects control switches to cooktop wiring. Moderate DIY repair, 1-2 hours.

This potentiometer is the rotary sensor behind the control knob. It converts knob rotation into an electrical signal the control board uses to adjust settings, restoring smooth, accurate response when a worn or erratic control causes inconsistent operation.

• Translates knob rotation into a variable-resistance signal for the electronic control
• Enables the control board to regulate power/heat or speed, depending on model
• Common failure symptoms: unresponsive or jumpy settings, dead spots when turning, or settings that drift
• Helps restore precise, repeatable adjustments at the knob

• Disconnect power to the appliance before servicing
• Pull off the knob and open the control panel to access the potentiometer
• Move wires one at a time to the new part; align the shaft/flat to the knob as noted
• Reassemble and test full range of adjustment; follow any model-specific calibration if required

This fan switch restores dependable control of your appliance's ventilation fan. It routes power to the blower motor so you can turn the fan on and off from the control panel when the original switch becomes worn or fails.

• Controls electrical power to the blower motor
• Restores reliable on/off fan operation from the user interface
• Typical symptoms: fan won't start, won't shut off, runs intermittently, or the switch/rocker feels loose or broken
• Contacts can wear or arc over time from repeated use

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the switch from the control panel; note wire positions and take a photo for reference
• Move wires one at a time to the matching terminals on the new switch; replace any heat-damaged connectors
• Reassemble, restore power, and test fan operation

Fixes burner that won't heat or indicator light stuck on. This infinite switch controls surface burner power and heat settings. Moderate DIY repair.

Fix intermittent burner failures or electrical issues with this range wiring harness. Restores power flow when connections are loose, burnt, or broken.

If your burner indicator light stays on constantly or burner runs at full heat on all settings, this infinite switch controls heat levels. 10-minute fix.

Exhaust fan won't turn off or stuck on? This rocker switch restores reliable blower control. Simple 5-minute fix—just disconnect wires and snap in new.

The fan control switch is the panel-mounted switch that sends power to the appliance's fan motor. Replacing a worn switch restores reliable on/off control and proper airflow so the fan starts and stops when it should.

• Provides user-operated on/off power to the fan/blower motor
• Helps regulate airflow for cooling, venting, or convection depending on model
• Typical symptoms: fan won't run, runs continuously, intermittent operation, or a loose/broken switch shaft
• Mounts behind the control panel and is actuated by the exterior knob/lever

• Disconnect power at the breaker before servicing
• Remove the control knob/actuator and panel trim to access the switch
• Note wire positions or take a photo; transfer wires one at a time to the new switch
• Secure with the original hardware, restore power, and test operation

Element won't heat or overheats? This infinite switch kit restores precise temperature control to your cooktop's burners. Fixes erratic heating issues.

Burner stuck on or won't turn off? This infinite switch restores precise heat control to your surface element. Takes about 20 minutes to replace.