Range / Cooktop / Oven Switch
Genuine Ge part
By: Ge
Part Number: WB24T10134
Burner won't turn off or stays on high? This infinite switch controls power to your surface element. Moderate DIY repair restores heat control.
Do-It-Yourself Stories from Customers like You
One burner stopped working due to short circuited control the seal over time started to allow the liquids to go down the control shaft causing the short Igor K. • Fair Lawn , NJ • April 26, 2016
Disconnected ( already tripped) breaker in the panel. Lifted cooked top unscrewed the glass top and set aside. I took the picture of the wires connected to the control on my ipad and replaced broken control. reconnected the wires as per picture. Cleaned the greased glass top and replaced the infinite switch seal for the broken control. Then reinstall glass top back on the cooktop and put the cooktop back in in place. Enable breaker in the panel and now i have good working cooktop again. ( do...
Read more
More
$119.95
- Compare At:
-
$141.54
- You Save:
-
$21.59
Genuine Ge part
By: Ge
Part Number: WB24T10167
Burner won't heat or stays stuck on? This surface element rocker switch restores reliable on/off control. Simple DIY repair—just 4 screws, 30 minutes.
Do-It-Yourself Stories from Customers like You
Switch rocker element (wb24t10167) would not switch from small to large burner size Hendrick J. • Marianna , FL • January 08, 2017
Worst part of job was sliding stove out from wall. Remove 4 small screws from shield on top of stove, disconnect two connectors from switch rocker, push lock tabs inward so you can push switch rocker outward from back toward burners threw frame of stove, insert new unit until click locks, reconnect wires, and reinsert shield back on top stove and secure with 4 screws removed earlier. Easy job, part shipped from AppliancePartsPros.com Fedex ASAP.
Read more
More
$49.62
- Compare At:
-
$59.54
- You Save:
-
$9.92
Genuine Frigidaire part
By: Frigidaire
Part Number: 316238202
The Dual Element Surface Switch is an OEM part for Frigidaire electric ranges and cooktops. It governs power distribution to the dual element.
Causes may be loose electrical terminals within the switch, defects from past power surges, or general wear over extended use.
Symptoms of a bad surface switch include:
- Inability to toggle one or both elements independently
- Elements activating intermittently or staying stuck on
- Overheating, sparks or strange sounds from faulty connections
- Repeated burning or singeing of cookware bottoms
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Both large burners were starting to go to higher heats at lower settings. James T. • Hilo , HI • April 23, 2023
I replaced both the large single element and the large dual element control switches. It appears the resistors were burning out. Problem seems to be fixed. Will know later when I do some simmering.
Read more
More
$85.95
- Compare At:
-
$103.14
- You Save:
-
$17.19
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304493153
The Door Switch is an OEM replacement part for Frigidaire wall ovens. It is a component located on the oven door that detects when the door is opened and closed. The door switch works alongside the control board to regulate oven operations based on door position.
Symptoms of a bad door switch can include:
- Oven failing to automatically go into bake or warm modes after door closure
- Interior lights not turning on when the door is opened
- Control buttons/display remaining constantly lit instead of dimming
- Oven not heating or functioning properly in different modes
Causes relate to normal wear over extended use as the door switch mechanism cycles with frequent door openings and closings. Moisture exposure or impacts could also degrade switch performance.
This OEM Frigidaire switch is compatible with Amana, Jenn-Air, KitchenAid, and some Electrolux wall oven models as well.
Do-It-Yourself Stories from Customers like You
Frigidaire microwave oven lights and timer work but oven doesn't heat Reese F. • Essex Junction , VT • August 16, 2015
I diagnosed this problem via the web and the advice was spot on. The problem was a failure of the bottom door switch. I used a multimeter to verify that the switched never closed properly. It took me a minute to figure out how to remove the old switch (press a release tab under the switch while simultaneously rotating counter-clockwise). That was about the most difficult part of the repair.
Read more
More
$56.95
- Compare At:
-
$68.34
- You Save:
-
$11.39
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304508926
Burner won't turn off or element light stays on? This range burner control switch regulates temperature and power. Moderate DIY repair, 30-60 minutes.
Do-It-Yourself Stories from Customers like You
The control knob was orginal equipment but the switch installed by a sears tech was not and the knob eventually would not work the switch Kevin W. • Yucca Valley , CA • December 19, 2016
I went on your website found the parts needed to make the repairs. I watched the short video on installation. The parts arrived just a few days after I placed the order. I finished the repair in less than an hour and had to wait a few minutes to test the switch since the power was off and on due to a wind storm. Simple easy to do repair and I saved $90.00 on service fee for a tech to do the repair.
Read more
More
$64.70
- Compare At:
-
$76.35
- You Save:
-
$11.65
Genuine Frigidaire part
By: Frigidaire
Part Number: 316580614
Burner won't spark or click when you turn the knob? This igniter wiring harness restores the electrical connection between switch and igniter. 30-minute DIY fix.
Do-It-Yourself Stories from Customers like You
The back left burner didn't light and didn't click when turned the knob Oceanna C. • Watsonville , CA • April 07, 2016
My husband and myself didn't agree on which part was the exact problem. He felt it was the valve. I felt it was the ignitor/ orifice. And we both agreed the Harness-Ignitor needed to be replaced. So we ordered all 3, and I'm not sure if in fact all three were needed or not, but now with those parts replaced, the range is working like brand new!! Thanks to all the videos and diagrams on the website we were able to fix it ourselves easily. And the price was cheaper then other websites, also it...
Read more
More
$78.78
- Compare At:
-
$93.75
- You Save:
-
$14.97
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304527841
The Rocker Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for turning the interior oven light on and off. The light switch allows visibility of the oven cavity for viewing food during the cooking process.
Causes can include normal wear and tear over time, exposure to heat inside the oven cavity, or accidental damage.
Symptoms of a bad oven light rocker switch include:
- The oven light failing to illuminate when the door is opened
- The light remaining on even when the door is closed
- An inconsistent or flickering oven light
- The switch itself becoming loose, cracked, or non-responsive
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
1 of the 4 burners would not ignite with its own control Shane W. • Fullerton , CA • November 15, 2022
Removed & replaced igniter switch assembly. The hardest part was figuring out how to remove the range top...look up a YouTube video with your manufacturer and model number to see how to do it.
Read more
More
$15.50
- Compare At:
-
$18.45
- You Save:
-
$2.95
Genuine Ge part
By: Ge
Part Number: WB24T10012
Burner stuck on high or won't adjust temperature? This range infinite switch controls surface element heat levels. Common DIY fix for uneven heating.
Do-It-Yourself Stories from Customers like You
The control switch for GE range had contact problem Yihua T. • Tucson , AZ • August 19, 2018
Replace the switch (part # WB24T10012).
Read more
More
$43.95
- Compare At:
-
$52.30
- You Save:
-
$8.35
Genuine Ge part
By: Ge
Part Number: WB24X449
Oven won't change modes or burner won't heat? The selector switch routes power to cooking functions. Moderate DIY repair with video guidance available.
Do-It-Yourself Stories from Customers like You
GE profile cooktop problems: dirty switch seals in glass top shorted infinite switch broken selector switch missing knob Hugh A. • Weaverville , CA • March 06, 2019
My cooktop repair was a total success from start to finish. I reviewed and later followed the APP repair video, which helped me decide if I wanted to tackle the repairs and guided me right before I started. The APP phone staff member was very helpful verifying the parts I had identified online using the model number of my older GE Profile cooktop to locate and view the correct online exploded view diagram. I told him it was a pleasure working with him. The parts arrived within 3 days of...
Read more
More
$79.95
- Compare At:
-
$94.34
- You Save:
-
$14.39
Genuine Ge part
By: Ge
Part Number: WB23M24
6" element switch
Do-It-Yourself Stories from Customers like You
The burner would not stay at the temperature you wanted. It would go to high eventually. Ronald S. • Columbia , SC • February 05, 2022
Talked to a representative at your company they said it was probably the infinite switch.
I purchased all four switches, replaced all four burner switches. Very easy to do. In less than an hour to replace all four.
Read more
More
$106.95
- Compare At:
-
$128.34
- You Save:
-
$21.39
Genuine Frigidaire part
By: Frigidaire
Part Number: 316239601KIT
Fix a burner that won't turn off or heat properly with this dual infinite switch. Controls both inner and outer element rings. Moderate DIY repair.
Do-It-Yourself Stories from Customers like You
Needed a surface element dual control switch for my frigidaire range as the surface element would remain on èven when the switch was turned off Michael H. • Lauderhill , FL • July 22, 2016
Relatively easy DIY
Read more
More
$63.65
- Compare At:
-
$133.26
- You Save:
-
$69.61
Genuine Frigidaire part
By: Frigidaire
Part Number: 318191000
Burner won't heat, stuck on high, or works intermittently? This cooktop burner control switch restores reliable on/off control. Easy DIY repair.
Do-It-Yourself Stories from Customers like You
Switch was bad on cooktop Carl S. • Farmville , VA • October 28, 2016
Replaced the switch
Read more
More
$77.23
- Compare At:
-
$103.97
- You Save:
-
$26.74
Genuine Whirlpool part
By: Whirlpool
Part Number: WP74003122
Fix a burner stuck on high or won't adjust temperature with this infinite switch. Controls cooktop burner heat levels. DIY repair in under 30 minutes.
Do-It-Yourself Stories from Customers like You
Element would stay on high even at lower settings why it would fail in the "high" mode is not a good design David M. • Suffield , CT • February 04, 2015
Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element
Read more
More
$61.56
- Compare At:
-
$73.26
- You Save:
-
$11.70
Genuine Frigidaire part
By: Frigidaire
Part Number: 318394803
Has three terminals.
Do-It-Yourself Stories from Customers like You
Oven light stayed on when door was closed Robert S. • Jacksonville , IL • June 14, 2015
When trouble shooting the problem I found that the light switch housing outer lip was broken allowing the switch to push through mounting surface behind the oven door. This is a slide in range so, I proceeded to pull the range away from the counter where I could unplug the power cord. Once the power was off like located the panel on the right upper side of the unit and removed the screws to allow access to the switch. I then unplugged the switch from the wiring harness and removed the damaged...
Read more
More
$52.68
- Compare At:
-
$63.22
- You Save:
-
$10.54
Genuine Lg part
By: Lg
Part Number: EBF60662911
This switch assembly is the door lock mechanism for select front-load washers. It detects when the door is closed and locks it during operation, allowing the washer to start and run safely without interruptions.
- Monitors door position and signals the control; failure can prevent the cycle from starting or trigger door/lock errors
- Engages the latch to secure the door during wash and spin; a bad lock may stop the cycle mid-wash
- Coordinates door unlock at cycle end; faults can delay or prevent unlocking
- Intermittent operation may cause sporadic starts or pauses
What's included: One switch assembly. Install notes:
- Disconnect power and turn off water supply before servicing
- Access the lock behind the front panel at the door opening; remove the door boot clamp to reach the mounting screws
- Move wire connectors to the new assembly one at a time to maintain placement
- Reassemble and verify proper locking and unlocking before running a full cycle
This part fixes the following symptoms
-
Doesn't shut off
-
Gas igniter glows, but will not light
See more...
Do-It-Yourself Stories from Customers like You
All the igniters spontaneously began to fire Michael S. • Adams , NY • October 12, 2019
Found a YouTube video online that provided instruction on how to change out the part.
Read more
More
$74.95
- Compare At:
-
$89.19
- You Save:
-
$14.24
Genuine Ge part
By: Ge
Part Number: WB24T10147
This high-amp SPDT switch routes power between circuits in cooking appliances to control items such as locks, element relays, or fans. Replacing a worn switch restores dependable operation and helps eliminate intermittent on/off issues. What it does:
- Single-pole, double-throw action directs power between NO/NC circuits based on actuator position
- Used to signal or control a component per the model's design (e.g., latch/lock, relay, fan)
- Failure symptoms can include no activation, stuck-on/off behavior, intermittent operation, or heat-damaged terminals
- Electrical tests may show incorrect continuity between COM–NO/NC when pressed or released
What's included:
- Includes: 1 SPDT high-amp switch
Install notes:
- Disconnect power at the breaker or unplug the appliance before servicing
- Label or photograph wiring; move leads to matching COM/NO/NC terminals on the new switch
- Mount with the correct actuator orientation and secure any bracket or screws
- Inspect connectors for heat damage; ensure tight spade fits, restore power, and test operation
Do-It-Yourself Stories from Customers like You
Faulty self cleaning latch Gregory K. • Bel Air , MD • December 28, 2016
Replaced faulty latch with new latch. New latch was different configuration, but the fit was okay. The only issue was that the wires to the electric motor were just barely long enough.
Overall easy repair if you have a T15 Torx bit, phillips screwdriver, and 1/4" nut driver. Hardest part is removing the gas cooktop to gain access to the cleaning latch. 0. Turn off electric to stove; remove the cast iron grates, center caps/orifices, and catch pans from the stovetop. 1. Disconnect the...
Read more
More
$21.95
- Compare At:
-
$26.12
- You Save:
-
$4.17