Range Hood Parts

Size: 3/4 inch od x 1/4 inch id.

This is a slide switch that controls the light or fan functions on a range hood. It mounts on the front control panel and slides to select different speed or on/off settings. Replace this part if the switch is broken, stuck, or no longer properly activates the hood's light or fan.

Range hood light bulb assembly illuminates your cooking area. Replace when lights flicker, fail to turn on, or provide dim lighting. Verify fit by model.

Range hood not venting smoke or odors? This blower assembly includes the motor and fan to restore proper ventilation. Moderate DIY repair for most users.

Fix a range hood that won't turn on, responds intermittently, or has a loose slider. This slide switch restores reliable control of fan and light settings.

Hood lights not working? This ceramic insulation base secures the lamp receptacle for reliable bulb connection. Easy DIY repair, typically under 30 minutes.

Protective cap that mounts over control switches on your range hood control panel. Replace if cracked, broken, or missing to keep switches properly aligned.

Keep your appliance's controls working reliably with this switch cover. It mounts over a switch to hold it in place and shield it from damage, helping ensure consistent actuation and long service life.

• Retains and protects a control/interlock switch within its housing
• Helps keep the switch aligned for reliable on/off detection
• Shields the switch from dust and incidental contact
• Cracked, loose, or missing cover can cause intermittent operation or no response when the control is pressed

• Disconnect power to the appliance before servicing
• Remove the necessary panel to access the switch; note wire positions/orientation
• Transfer any clips/screws from the old cover and seat the switch fully
• Secure wiring away from pinch points before reassembly

Grease filter for range hoods and over-the-range microwaves. Dimensions: 10-1/2" x 10-1/2" x 3/32" (10.5 x 10.5 x 0.09375). Dome shape. Captures grease from cooking air. Replace when clogged, discolored, or every 6-12 months.

Captures grease and debris to protect your range hood's internal components. Replace when discolored or clogged to maintain ventilation performance. Verify fit with your model number.

Fix a range hood control knob that stops responding or only works in one position. This rotary switch restores precise fan and light selection.

Range hood fan won't change speeds or stuck on one setting? This speed control switch lets you adjust ventilation levels for proper smoke and odor removal.

This is a set of two charcoal filters designed for a range hood operating in recirculating (non-vented) mode. The charcoal absorbs odors and smoke from cooking before the air is recirculated back into the kitchen. Replace these filters if you notice lingering cooking odors, reduced air freshening performance, or if they have been in use for six months or longer.

The Range Hood Halogen Lamp is an OEM part for Bosch range hoods. It provides illumination for the cooking area beneath the range hood, enhancing visibility while cooking. This halogen lamp is designed to fit seamlessly into the range hood, ensuring a bright and focused light.

You should replace this halogen lamp if it burns out or becomes faulty. Causes of a bad halogen lamp can include filament burnout from prolonged use, electrical surges, or damage from handling during cleaning or maintenance.

Symptoms of a bad halogen lamp include:

• Dim or flickering light
• No light when the range hood is turned on
• Discoloration or dark spots on the lamp
• Frequent bulb replacements needed

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This replacement control push button restores a clean, responsive press on the control panel when the original is cracked, missing, or sticking, so you can reliably actuate the switch beneath it.

• Interfaces with the underlying switch/rocker on the control panel to select functions
• Provides the tactile surface for choosing settings, depending on model
• Helps maintain proper alignment and travel for consistent operation
• Typical symptoms: cracked or missing cap, sticking/binding, wobbly feel, won't stay seated

• Disconnect power at the breaker before servicing any controls
• Access the control panel and note the button's orientation before removal
• Release bezel/retaining tabs and remove the old button; transfer any clips if present
• Seat the new button on the switch stem, reassemble, and test operation

Includes 12 washers.