Range Hood Parts

This replacement knob restores a clean look and reliable control of your unit's settings. It fits onto the control shaft to give you a secure, easy-to-grip dial when the original knob is cracked, loose, or missing.

• Press-fits onto a control shaft to operate the switch or speed control
• Provides a secure grip for selecting settings as intended
• Replaces damaged, cracked, or missing knobs
• Helps address slipping, free-spinning, or hard-to-turn controls

• Disconnect power to the appliance before servicing
• Pull the old knob straight off; avoid prying against the panel to prevent damage
• Align the flat/D-shaped insert with the shaft and press on until fully seated
• Restore power and test operation

This is a genuine OEM replacement o-ring sourced directly from the manufacturer for use on range vent hood switches. The o-ring provides a tight seal for the switch and keeps smoke from escaping through the switch connection. If the o-ring becomes worn or damaged, the vent will not remove smoke during cooking and should be replaced. Heat and debris pulled through the vent may cause the o-ring to warp. O-rings are not designed to last forever and may need to be replaced during the life of the appliance to keep it functioning correctly.To start, disconnect the power to the vent hood and dismantle the vent in order to reach the switch. To start, disconnect the switch and locate the o-ring. Remove the old one and dispose of it. Place the new o-ring in the groove and press firmly to seal the part. Lubrication is not necessary for installing the new o-ring. Reassemble the switch and put the vent hood back in place. Connect the power and try the switch to make sure it works. This o-ring is made of heavy-duty black rubber is and sold individually. It is designed for use in range hoods manufactured by Thermidor.

This replacement fan motor drives the blower that moves air through your ventilation system. Replace a failing motor to help restore proper airflow and reduce noise during operation. What it does:

• Spins the blower wheel/impeller to move air through the venting system
• Helps clear steam, smoke, and odors by maintaining consistent airflow
• Can address symptoms like a fan that won't start, just hums, runs slowly, or is unusually noisy
• Resolve overheating or a burning smell coming from the motor area

• 1 motor

• Disconnect power at the breaker before servicing
• Note wire locations and motor orientation for correct reassembly
• Ensure the blower wheel is secure and spins freely after installation
• Test run before final reassembly and check for vibration or rubbing

This bezel is a small trim piece that finishes an opening on the appliance's control area. It restores a clean, factory look and helps protect the underlying panel when the original is cracked, loose, or missing.

• Frames the control opening for a finished appearance
• Helps shield panel edges from wear and debris
• Typical symptoms: cracked plastic, broken tabs, discoloration, loose or missing trim

• Disconnect power and allow the appliance to cool before servicing
• Remove any adjacent knob or trim as needed for access
• Release the old bezel's tabs or screws and note its orientation
• Install the new bezel in the same position, then reinstall removed parts and test

This replacement control push button restores a clean, responsive press on the control panel when the original is cracked, missing, or sticking, so you can reliably actuate the switch beneath it.

• Interfaces with the underlying switch/rocker on the control panel to select functions
• Provides the tactile surface for choosing settings, depending on model
• Helps maintain proper alignment and travel for consistent operation
• Typical symptoms: cracked or missing cap, sticking/binding, wobbly feel, won't stay seated

• Disconnect power at the breaker before servicing any controls
• Access the control panel and note the button's orientation before removal
• Release bezel/retaining tabs and remove the old button; transfer any clips if present
• Seat the new button on the switch stem, reassemble, and test operation

This replacement motor powers the fan/blower in your ventilation unit to move air efficiently. Use it to restore airflow when the original motor becomes noisy, slow to start, or stops running altogether.

• Spins the blower/fan wheel to pull air through the unit and out through ducting or filters
• Maintains proper ventilation performance and airflow
• Common symptoms: fan won't start or only hums; runs slowly or stalls; excessive noise or vibration; intermittent shut-off/overheating
• Suitable replacement when the existing motor windings, bearings, or thermal protector have failed

• Disconnect power at the breaker before servicing; allow components to cool
• Access the motor by removing the grille/filters and blower housing as applicable
• Transfer the blower wheel and any reusable brackets/wiring from the old motor; align the shaft flat and secure the set screw
• Spin the wheel by hand to confirm free movement; test run before final reassembly

This control knob replaces a worn or missing knob on your range or cooktop. It attaches to the control stem so you can reliably select heat or temperature settings and restore smooth operation with a clean, finished look.

• Mounts on the control stem to turn the burner or oven control
• Restores positive engagement when the original knob is cracked, stripped, loose, or missing
• Helps ensure smooth turning and proper indexing of settings
• Common symptoms: knob slips or falls off, hard to turn, damaged or missing knob

• Disconnect power and, if applicable, shut off gas before servicing
• Pull the old knob straight off the control stem; avoid prying on the panel
• Align the new knob with the stem and press it on fully until seated
• Verify smooth operation and that the indicator aligns with settings

This small door-activated microswitch signals the control that the microwave door is fully closed so cooking can start, and it opens the circuit when the door is opened. Replacing a worn switch restores reliable, safe start/stop operation. What it does:

• Detects door position and permits operation only when the door is closed
• Interrupts power when the door opens during a cycle
• Helps resolve won't-start unless pressing on the door, starts then immediately stops, or intermittent operation when opening/closing the door
• In some cases, prevent fuse or breaker trips caused by a failing interlock switch

• 1 switch

• Disconnect power; if servicing a microwave, the high-voltage capacitor can retain a dangerous charge—discharge it safely before working
• Access the interlock switch bracket near the door latch; note wire positions and switch orientation
• Move one wire at a time to the new switch and ensure the actuator aligns with the door latch
• Inspect the latch and mounting bracket; replace if worn or damaged

Color: metallic. Measures about 13-1/2 inches wide by 5 inches high.

The Grease Filter is an OEM part for Bosch ranges and cooktops. It is responsible for capturing and containing grease, oils, and other vapors produced from cooking to help keep indoor air fresh and prevent buildup. Regular cleaning is important to maintain optimal performance.

Causes of a bad grease filter can include excess buildup that blocks airflow from frequent high-heat cooking. Exposure to flames or excessive heat may cause damage over time as well.

Symptoms of a bad grease filter include:

• Reduced suction power and airflow from the range hood
• Grease accumulation on surrounding surfaces below the hood
• Unpleasant cooking odors escaping into the kitchen rather than being vented outside

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This replacement motor powers the blower in your ventilation unit, spinning the fan blade or wheel to move air through the housing and ductwork. Replace it when the original motor becomes noisy, stalls, or fails to start.

• Drives the fan blade/blower wheel to move air through the unit
• Restores proper airflow and ventilation performance
• Common symptoms: loud humming or grinding, won't start, slow/weak airflow, intermittent operation, overheating/shutting off
• Often needed when the shaft is seized or bearings are worn

• Disconnect power at the breaker before servicing
• Access the blower assembly; remove the grille or filters to reach the motor
• Note wire locations; transfer wiring, mounting hardware, and the fan blade/blower wheel from the old motor if applicable
• Ensure the blade/wheel spins freely before reassembly, then restore power to test

This light lens covers and diffuses the fixture's bulb, protecting it from dust, moisture, and accidental contact while softening light output for better visibility. A cracked or missing lens can leave the bulb exposed and create harsh glare.

• Diffuses light for a softer, more even glow
• Shields the bulb from dust, moisture, and debris
• Restores a clean, finished look to the light area
• Common symptoms: cracked, yellowed, warped, loose, or missing lens; glare from an uncovered bulb

• Disconnect power and allow the bulb to cool before servicing
• Remove the old lens by releasing tabs or screws; note orientation
• Handle the new lens carefully; avoid flexing or overtightening fasteners
• Ensure the lens seats fully, restore power, and test the light

Size: 10-32 GXTT FLP.595 S

Knob, blk (cvs)

The Control Knob is an OEM part for Bosch ranges and cooktops. As the interface regulating gas flow, control knobs activate precise burner levels through internal calibration.

Causes of failure include loosened set screws beneath allowing knob slippage. Prolonged heat and moisture exposure may also degrade contact surfaces over time.

Symptoms of faulty knobs include:

• Burners failing to engage or not matching dial settings
• Inability to decrease output levels from full flame
• Knobs wobbling insecurely or detaching entirely

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This charcoal filter is used in recirculating range hoods to reduce cooking odors and smoke. Replacing a saturated filter restores ventilation performance and helps keep kitchen air fresher when venting air back into the room. What it does:

• Adsorbs cooking odors and vapors when the hood is set to recirculate indoors
• Helps maintain proper airflow and capture smoke/steam during cooking
• Replace if saturated, damaged, or shedding carbon
• Common signs: lingering odors, reduced airflow, discoloration, or loose carbon granules

• 1 charcoal filter

• Disconnect power to the hood before servicing
• Remove/open the filter cover or grille; release the old filter from its clips or frame
• Insert the new filter with proper orientation; secure it and reinstall the cover
• Charcoal filters are not washable or reusable; replace periodically as needed

This replacement switch restores reliable control to your Broan ventilation unit. The fan or light doesn't respond, only works intermittently, or the control feels loose; replacing a worn internal switch is a simple, effective fix.

• Provides on/off control for a circuit in the appliance
• Replaces a worn, intermittent, or stuck switch to restore consistent operation
• Common symptoms: no response, works only when held, inconsistent operation, loose or damaged actuator
• Helps maintain safe, dependable operation of the control panel

• Disconnect power at the breaker and verify no voltage before servicing
• Access the control panel; note wire positions or take a photo for reference
• Transfer wires one at a time to the new switch and secure it in the original mounting
• Test operation before reassembling covers and panels

This replacement filter screens out debris to help protect internal components and maintain your appliance's performance. A clean, intact filter supports proper flow or airflow and helps prevent premature wear on related parts.

• Captures particles before they reach pumps, fans, or ducts to help prevent clogs and buildup
• Helps maintain consistent water or air movement for reliable operation
• Supports overall efficiency and reduces strain on the system
• Typical signs it needs replacement: visible damage or warping, heavy residue that won't clean off, restricted flow/air movement, recurring clogs

• Disconnect power and allow any hot surfaces to cool; shut off water if applicable
• Access the filter per your model's instructions; note its orientation and any locking tabs
• Seat the new filter fully and secure without forcing
• Restore power/water and verify proper operation and flow/air movement