Washer Touch Pad

This is a Whirlpool washer main console. The main console is the component at the top of the washer containing the control knobs. Any burning smell from the console or control board could indicate a short panel, and use should be discontinued immediately. If controls are unresponsive, use a voltage tester to check the control board and any connections to verify that the control board is faulty.Remove the old console by unscrewing the top screws on the back panel. There should be two clips that fasten the console in place. Remove these with a flathead screwdriver. The product was sourced directly from the manufacturer as a genuine OEM part. This washer console is sold individually. This part is compatible with Whirlpool, Roper, JennAir, Maytag, and Magic Chef.

This backsplash assembly is the rear console housing for a washer's controls. It supports and protects the user interface components and finishes the top, restoring a secure, aligned control area when the original panel is cracked or loose.

• Houses and supports the washer's control components and mounting hardware
• Shields wiring and controls from splashes at the rear of the top panel
• Restores proper fit and alignment for knobs, buttons, and overlays
• Common symptoms: cracked or broken console, loose or rattling controls, broken mounting tabs, cosmetic damage

• Disconnect power and, turn off water supply before servicing
• Remove control knobs and screws/clips securing the console; carefully lift the assembly
• Label or photograph wiring and transfer controls/mounting hardware to the new panel
• Reinstall, ensuring all tabs and screws are fully seated; watch for sharp edges

This control panel is designed for use with washing machines. It's on the top back area of the appliance and houses a display and several buttons to control various components in the appliance. It's responsible for starting and stopping components, such as the drain pump and drive motor. If the display isn't working or the washer doesn't spin, fill, or drain, the control panel may be causing the issue.If this part is faulty, it should be replaced. Use work gloves for hand protection and pull the washing machine away from the wall to unplug it. Pull the control knob off the front of the console panel and move to the back of the appliance. Take out the screws on the top of the back panel. Push the control panel back while using a putty knife under the right corner to release the mounting clip. Do the same thing on the other side. Document where the wires are connected to the control panel before removing it. Install the new part and reconnect all the wires.This control panel is made for use with Maytag washing machines. It's an authentic OEM replacement part sourced directly from the manufacturer. The part is sold as an individual item.

The User Control and Display Console is an OEM part for Whirlpool washing machines. It houses the digital display and membrane buttons that allow for cycle and setting selection. As the interface constantly subjected to touch during use, this console can show normal wear like faded graphics or non-responsive buttons over time.

Causes may include extended use wear from repeated cycling as well as occasional moisture exposure inside the console.

Symptoms of a faulty console include:

• Cycle or temperature buttons not responding
• Unreadable or blank display screen
• Inability to scroll through options

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This backsplash assembly replaces the rear panel on a freestanding range to restore wall protection and the appliance's finished rear appearance. It covers openings at the back and helps keep wiring and components protected and tidy. What it does:

• Covers the rear opening of the range to protect the wall from heat, grease and spills.
• Conceals wiring and access holes to help keep connections protected and out of view.
• Restores damaged, dented, rusted or missing rear trim caused by impacts, corrosion or wear.
• Provides the correct mounting surface for rear-mounted trim and components.

• Disconnect power to the appliance at the breaker before beginning any service.
• Remove the range from the wall if needed to access mounting screws; have a helper if the range is heavy.
• Hold the new backsplash in place and confirm alignment before tightening fasteners; retain original screws if replacement hardware is not supplied.

The Control Panel is an OEM part for Whirlpool washing machines. It is the interface that users interact with to operate the washer, allowing cycle and setting selections to be made. The control panel coordinates closely with the washer's electronic control board to initiate and monitor cycles.

Causes of a bad control panel may be due to prolonged exposure, resulting in cracking, damage from liquid ingress, or components wearing out over time.

Some symptoms of a faulty control panel are:

• Buttons sticking, faulty, or unresponsive  
• Inability to scroll through cycles or make selections
• Erratic display lights or missing display functions
• The control panel failing to power on or communicate with other components

This OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This control panel assembly replaces the front user interface and button/touch controls so you can restore normal control of oven functions and display information. Fits the original factory mounting and connections for a direct replacement. What it does:

• Replaces damaged or unresponsive front control buttons, touchpad, and status display
• Restores the ability to select cycles, start/stop, and change settings from the console
• Common symptom fix: unresponsive or intermittent control inputs and blank or incorrect display messages
• Works with the existing wiring harness and mounting points for a straightforward swap

• Disconnect power to the appliance before accessing internal components to avoid shock or injury
• Remove any trim or access panels to reach the control assembly
• Handle the display and ribbon cables carefully; flexing or pulling can damage connectors

This replacement console is the outer control panel housing that holds the selector buttons, knobs, and display bezel—restoring the appliance's front control area for correct button access and a finished appearance. What it does

• Provides the outer housing for the control buttons, display, and selector components.
• Protects underlying electronic controls and wiring from everyday use and debris.
• Restores secure button/knob mounting and proper alignment for user input.
• Can eliminate rattling or loose-feeling controls caused by cracked or broken console pieces.

• One console housing

• Disconnect power to the appliance before starting any work.
• Installation typically requires removing screws or clips and carefully releasing tabs to remove the old console.
• Handle plastic tabs and the display bezel gently to avoid cracking; align tabs and fasteners before tightening.
• Reconnect wiring securely and verify function before final reassembly.

This control panel is the exterior console trim that houses the user controls and display, restoring the appliance's interface and appearance. It lets you access and operate settings easily and keeps buttons and indicators protected. What it does:

• Replaces a cracked, faded, or damaged front console so buttons and displays are clearly visible
• Restores a secure mounting surface for control switches and touchpads
• Helps prevent dirt and moisture from reaching internal electronics behind the console
• Improves the appliance's cosmetic appearance and user operability

• One control panel

• Disconnect power to the appliance before beginning any work to avoid electrical shock
• Removal may require removing trim pieces or bezels; keep all fasteners for reassembly
• Handle panel carefully to avoid scratching or damaging the finish during install
• If the panel includes electronic components, avoid touching circuit contacts.

This replacement backsplash assembly restores the finished rear panel on compatible ranges, protecting the wall behind the cooktop and returning the appliance's original appearance. Use it when the original panel is bent, rusted or cosmetically damaged. What it does

• Covers and protects the rear area of the cooktop from heat, grease and splatter
• Restores the appliance's finished look after dents, scratches or corrosion
• Provides the mounting surface for rear-mounted controls and components
• Prevents drafts and gaps behind the range that can collect debris

• Disconnect power to the range before beginning any service to avoid shock
• Typical installation requires removing a few screws and lifting the old panel out; basic hand tools are usually sufficient
• Take care with sharp edges and painted surfaces to avoid cuts or damage

This backsplash assembly replaces a damaged or worn rear backguard on ranges and cooktops, restoring a clean appearance and covering the appliance's rear controls and wiring for safe, reliable operation. What it does:

• Covers and protects the range's rear control area and internal wiring from spills, heat, and debris
• Restores a finished look when the original backguard is dented, scratched, bent, or missing
• Provides mounting surface for controls and trim components when applicable
• Helps maintain proper airflow and safety clearances around rear components

• Disconnect power to the appliance before starting any repair
• Removal of control panel or trim may be required; follow OEM instructions
• Handle carefully to avoid scratching finished surfaces; two people may be helpful for alignment