Washer Heating Element

This heater assembly warms the wash water inside the tub so the control can reach and maintain the selected temperature. Replacing a failed element restores proper heating performance and helps return cycle times to normal. What it does:

• Heats the water in the washer's tub during applicable cycles
• Helps the control reach and hold target temperatures for better cleaning
• Failure symptoms can include cold wash water, extended cycle times, and reduced cleaning performance
• Visual damage or an open circuit on the element indicates replacement is needed

• 1 heater assembly

• Disconnect power and turn off water before servicing
• The heater mounts at the bottom of the outer tub; remove front or rear panels as required by your model to access it
• Note wire locations; loosen the center nut, press the stud to release the old seal, and carefully withdraw the element
• Seat the new gasket evenly, tighten the nut to compress the seal, then run a test cycle to check for leaks and proper heating

The Washer Heater Assembly is an OEM component specifically designed for LG washing machines. It provides heated water to wash cycles, helping activate detergents and release tough soils for deeper cleaning. 

Causes of a faulty heater assembly typically include cracks in the heater element from chemical exposure or thermal expansion/contraction cycles over time. Electrical connections can corrode from mineral deposits.

Symptoms of a bad heater assembly include: 

• Inability to select hot water cycles  
• Slow or incomplete activation of detergents
• Reduced cleaning performance on heavily soiled loads
• Error codes indicating temperature sensor problems

This OEM LG part is also compatible with select Sears/Kenmore washers.

This electric heating element assembly restores proper heat in your electric dryer so clothes dry evenly and on time. It replaces a failed heater that causes long dry times or no heat.

• Generates and regulates the electric heat used during drying cycles
• Common failure signs include no heat, very long dry times, and clothes remaining damp after a full cycle
• Can help resolve tripping of thermal cut-off caused by a shorted element
• Restores consistent drying performance when the original heater burns out

• Unplug dryer and disconnect power before service
• Access is typically from the rear or front panel depending on model
• Transfer any reusable hardware and wiring in the same positions
• After installation, run a test cycle to ensure proper heating and airflow

10-inch heating element that restores proper heat production in affected appliances. Replaces a worn or failed element to help resolve issues like no heat or unusually long cycle times. What it does:

• Generates heat so your appliance can reach normal operating temperatures.
• Common symptoms it addresses: little or no heat, longer-than-normal cycles, or intermittent heating.
• Replaces a single failed element to return consistent heating performance.

What's included: One heating element. Install notes:

• Disconnect the appliance from power before attempting any repair.
• Allow the element to cool and handle carefully to avoid bending or damaging the coil.
• Ensure the terminal connections are secure and free of corrosion; tighten or replace fasteners as needed.

NOTE: IF THERMISTOR HAS TERMINALS WIRE HARNESS HAS TO BE CHANGED PART# 137288900 PER FRIGIDAIRE

The HEATER is an OEM component specifically designed for Whirlpool washing machines. It raises water temperature during heated cycles for effective cleaning. 

This wash heater element features carefully engineered heating coils and wiring to heat incoming tap water. Elevated temperature boosts the performance of detergent formulations to cut through tough stains on clothes and bedding.

Causes of a bad washer heater can include cracked or broken heating coils, loose connections to internal wiring, or accumulated limescale buildup inhibiting heat transfer.

Symptoms of a bad Heater include:

• Inability to reach or maintain desired water temperature 
• Fluctuations in water heat during cycles
• Reduced cleaning effectiveness on heavily soiled items
• Error messages related to abnormal temperature readings

This part is also compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, and Kenmore washing machines.

This heater assembly restores consistent, controlled heat inside your appliance so cycles reach the correct temperature. Replacing a failed heating element assembly helps resolve no-heat complaints and performance issues that leave loads cold or extend run times.

• Generates the heat required during the appliance's heating phases so temperatures rise as intended
• Works with thermostats/sensors to achieve and maintain target temperature
• Typical symptoms: no heat, lukewarm operation, unusually long cycles, or heating-related error codes
• Often confirmed by an open element or out-of-range resistance in continuity tests

• Disconnect power and allow the appliance to cool completely before servicing
• Access the heater per the service documentation; photograph wiring and routing to aid reassembly
• Handle the element carefully to avoid bending or damaging coils; transfer any brackets/sensors from the original if they are not supplied with the new part
• After installation, inspect and clear airflow or circulation paths and verify correct voltage before test operation

This heating element replaces the dishwasher tub heater to warm wash water and support drying performance. Restores proper water temperature so detergents and rinse agents work effectively during cycles. What it does:

• Heats wash and rinse water to help remove soils and dissolve detergent
• Supports the dry cycle by raising tub temperature for improved moisture removal
• Helps maintain correct cycle temperatures for sanitation and cleaning performance
• A failed element can cause no-heat conditions, poor drying, or extended cycle times

• Disconnect power to the appliance before starting any work to avoid electric shock
• Inspect and replace only the element shown in the service diagram; handle with care to avoid damage
• Verify electrical connections and test the element for continuity with a multimeter before and after installation

This heater is the electric heating element that warms air or water so your appliance reaches the proper operating temperature. Replacing a failed heater restores normal heating performance and helps cycles finish correctly. What it does:

• Generates heat needed for normal drying or wash cycles
• Allows the appliance to reach and maintain operating temperature
• Common symptom: appliance runs but does not heat or takes much longer to finish
• Common symptom: cycles complete without expected temperature or sanitizing action

• One replacement heater element

• Turn power to the appliance off at the breaker before starting any repair
• Handle the element carefully to avoid bending or damaging terminals
• Follow the appliance service manual for panel removal and wiring re-connection

The Washing Machine Heater Assembly is designed to maintain optimal water temperature during wash cycles, ensuring your washer operates efficiently. This genuine OEM part features AC120V and 1200W specifications, providing reliable and consistent heating for your appliance. Made from durable Incoloy800, the heater offers long-lasting performance and resistance to wear and tear. Its precise design ensures a perfect fit with compatible Samsung washing machine models, making installation straightforward. Replacing a faulty heater wash component with this genuine OEM part restores your washerGÇÖs efficiency, helping to save energy and enhance the quality of your laundry. Trust in this high-quality, original part to keep your washing machine functioning at its best, providing you with dependable performance for years to come.

This heater assembly replaces the dryer's heating element and housing to restore warm airflow for drying cycles. It's a direct-replacement assembly that re-establishes the appliance's heat source when the dryer won't heat properly. What it does:

• Houses the electric heating element that produces heat for drying cycles
• Replaces a burned-out element, open circuit, or damaged housing that can stop the dryer from heating
• Helps resolve symptoms such as no heat, only air tumbling, or weak/partial heating
• Works with the dryer's blower and thermostat to deliver consistent drying temperatures

• One heater assembly (heating element installed in housing)

• Disconnect power to the dryer (unplug or shut off breaker) before servicing
• Allow components to cool and wear gloves to protect hands from sharp edges
• Verify the part number matches the dryer's parts list before installation